DIN 13-19-1999 ISO general purpose metric screw threads - Part 19 Nominal profiles《ISO一般用途米制螺纹 第19部分 标准牙形》.pdf

《DIN 13-19-1999 ISO general purpose metric screw threads - Part 19 Nominal profiles《ISO一般用途米制螺纹 第19部分 标准牙形》.pdf》由会员分享，可在线阅读，更多相关《DIN 13-19-1999 ISO general purpose metric screw threads - Part 19 Nominal profiles《ISO一般用途米制螺纹 第19部分 标准牙形》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、DEUTSCHE NORM November 1999 I General purpose IS0 metric screw threads I DIN - Part 19: Nominal profiles I 13-19 ICs 21.040.10 Metrisches ISO-Gewinde allgemeiner Anwendung - Teil 19: Nennprofile This standard, together November 1999 edition, supersedes December 1986 edition. with DIN IS0 68-1, In ke

2、eping with current practice in standards published by the International Organization for Standardization (ISO), a comma has been used throughout as the decimal marker. Foreword This standard has been prepared by Technical Committee Gewinde of the Normenausschu Technische Grundlagen (Fundamentals in

3、Technology Standards Committee), taking into account the specifications of The adoption of a number of IS0 Standards (e.g. IS0 724, IS0 965 series) as national standards led the responsible committee to revise the DIN 13 series of standards. See the table in the Explanatory notes of DIN 13-1 for an

4、overview of DIN and DIN IS0 Standards for screw threads. DIN IS0 68-1. Amendments As compared to the December 1986 edition, the standard now only covers nominal profiles. The basic profile has been included in DIN IS0 68-1. Previo us edit ions DIN 13-30: 1960-08, 1964-06; DIN 13-1 9: 1972-05, 1986-1

5、 2. All dimensions are in mm. 1 Scope This standard applies to general purpose IS0 metric screw threads having the basic profile specified in DIN IS0 68-1. It specifies the nominal profiles for mating external and internal threads with or without clearance on the flank, on which tap dimensions are b

6、ased. 2 Normative references This standard incorporates, by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text, and the titles of the publications are listed below. For dated references, subsequent amendments to

7、or revisions of any of these publications apply to this standard only when incorporated in it by amendment or revision. For undated references, the latest edition of the publication referred to applies. Continued on pages 2 and 3. Translation by DI N-Sprachendienst. In case of doubt, the German-lang

8、uage original should be consulted as the authoritative text No pari of this translation may be reproduced without the prior permission of Ref. No. DIN 13-19 : 1999-1 - . . V Deutsches Institut fur Normung e VI Berlin Luth Verlag GmbH, D-10772 Berlin, hac the exclusive right of sale for German Standa

9、rds (DIN-Normen) English price group 05 Sales No 0105 04 O0 Page 2 DIN 13-19 : 1999-11 DIN 2244 DIN IS0 68-1 General purpose IS0 screw threads - Basic profile - Part 1: Metric screw threads DIN IS0 724 DIN IS0 965-1 Screw threads - Terminology (IS0 68-1 : 1998) General purpose IS0 metric screw threa

10、ds - Basic dimensions (IS0 724 : 1993) General purpose IS0 metric screw threads - Tolerances - Part 1 : Principles and basic data (IS0 965-1 : 1998) 3 Concepts See DIN 2244. 4 Nominal profiles The thread root contour at the basic major diameter of the internal thread is optional, the flank, however,

11、 shall be straight up to diameters D and D + El. The nominal sizes for general purpose IS0 metric screw threads specified in the DIN 13 series of standards are based on the nominal profile without clearance on the flank shown in figure 1. Profiles with clearance on the flank as shown in figures 2 an

12、d 3 are based on the fundamental deviations es and El specified in DIN IS0 965-1. Internal thread External thread Diameters of internal thread thread Diameters of external Figure 1: Nominal profile for mating thread without clearance on the flank (zero profile) Internal thread External thread Thread

13、 diameters as in figure 1. Figure 2: Nominal profile for mating thread with clearance on the flank based on fundamental deviations for external thread Internal thread External thread Thread diameters as in figure 1. Figure 3: Nominal profile for mating thread with clearance on the flank based on fun

14、damental deviations for external and internal thread Page 3 DIN 13-19 : 1999-11 Key to figures 1 to 3: D = d = basic major diameter (nominal diameter) =d-2Hl=d-1,082532P 3 4 D, = d, = d - -H = d - 0,649519 P d, = d, - 2 - - - = d - 1,226869 P (; B) H d, = d, - 6 J3 H = -P = 0,866025 P 2 D-Dl 5 HI = = - H = 0,541 266 P 2 8 d-d3 17 24 = -H = 0,613435 P h,= H 6 2 R = = 0,144338P