BS ISO 6020-3-2015 Hydraulic fluid power Mounting dimensions for single rod cylinders 16 MPa (160 bar) series Compact series with bores from 250 mm to 500 mm《液压流体动力 16MPa(160bar)系列.pdf

《BS ISO 6020-3-2015 Hydraulic fluid power Mounting dimensions for single rod cylinders 16 MPa (160 bar) series Compact series with bores from 250 mm to 500 mm《液压流体动力 16MPa(160bar)系列.pdf》由会员分享，可在线阅读，更多相关《BS ISO 6020-3-2015 Hydraulic fluid power Mounting dimensions for single rod cylinders 16 MPa (160 bar) series Compact series with bores from 250 mm to 500 mm《液压流体动力 16MPa(160bar)系列.pdf（24页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS ISO 6020-3:2015Hydraulic fluid power Mounting dimensions for single rod cylinders, 16 MPa (160 bar) seriesPart 3: Compact series with bores from 250 mm to 500 mmBS ISO 6020-3:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 6020-

2、3:2015. It supersedes BS ISO 6020-3:1994 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee MCE/18/-/3, Cylinders.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to includ

3、e all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2015. Published by BSI Standards Limited 2015ISBN 978 0 580 81177 7 ICS 23.100.20 Compliance with a British Standard cannot confer immunity from legal obligations.This B

4、ritish Standard was published under the authority of the Standards Policy and Strategy Committee on 30 September 2015.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS ISO 6020-3:2015 ISO 2015Hydraulic fluid power Mounting dimensions for single rod cylinders, 16 MPa (160 b

5、ar) series Part 3: Compact series with bores from 250 mm to 500 mmTransmissions hydrauliques Dimensions dinterchangeabilit des vrins 16 MPa (160 bar) simple tige Partie 3: Srie compacte, alsages de 250 mm 500 mmINTERNATIONAL STANDARDISO6020-3Second edition2015-08-01Reference numberISO 6020-3:2015(E)

6、BS ISO 6020-3:2015ISO 6020-3:2015(E)ii ISO 2015 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2015, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical

7、, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, Switzerla

8、ndTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 6020-3:2015ISO 6020-3:2015(E)Foreword ivIntroduction v1 Scope . 12 Normative references 13 Terms and definitions . 14 Dimensions . 15 Bore sizes .26 Piston stroke tolerances .27 Mounting styles 28 Piston rod characteristics

9、 .29 Identification statement (reference to this part of ISO 6020) .2Bibliography .13 ISO 2015 All rights reserved iiiContents PageBS ISO 6020-3:2015ISO 6020-3:2015(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member b

10、odies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental a

11、nd non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are d

12、escribed in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is draw

13、n to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on t

14、he ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment

15、, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this document is ISO/TC 131, Fluid power systems, Subcommittee SC 3, Cylinders.This second edition can

16、cels and replaces the first edition (ISO 6020-3:1994), which has been technically revised.ISO 6020 consists of the following parts, under the general title Hydraulic fluid power Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series: Part 1: Medium series Part 2: Compact series Part 3

17、: Compact series with bores from 250 mm to 500 mmiv ISO 2015 All rights reservedBS ISO 6020-3:2015ISO 6020-3:2015(E)IntroductionIn hydraulic fluid power systems, power is transmitted and controlled through a liquid under pressure within an enclosed circuit.One component of such systems is the fluid

18、power cylinder. This is a device that converts power into linear mechanical force and motion. It consists of a movable element, e.g. a piston and piston rod, operating within a cylindrical bore. ISO 2015 All rights reserved vBS ISO 6020-3:2015BS ISO 6020-3:2015Hydraulic fluid power Mounting dimensio

19、ns for single rod cylinders, 16 MPa (160 bar) series Part 3: Compact series with bores from 250 mm to 500 mm1 ScopeThis part of ISO 6020 establishes metric mounting dimensions for single rod compact series hydraulic cylinders with bores from 250 mm to 500 mm for use at 16 MPa (160 bar1), as required

20、 for interchangeability of commonly used hydraulic cylinders.NOTE 1 This part of ISO 6020 allows manufacturers of hydraulic equipment flexibility in the design of metric cylinders and does not restrict technical development, but does provide basic guidelines.NOTE 2 The compact series dimensions are

21、most applicable to square-head cylinders.This part of ISO 6020 applies only to the dimensions of manufactured products. It does not apply to their functional characteristics.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indisp

22、ensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 273, Fasteners Clearance holes for bolts and screwsISO 3320, Fluid power systems and components Cylinder bor

23、es and piston rod diameters and area ratios Metric seriesISO 4395, Fluid power systems and components Cylinder piston rod end types and dimensionsISO 5598, Fluid power systems and components VocabularyISO 6099, Fluid power systems and components Cylinders Identification code for mounting dimensions

24、and mounting typesISO 6162-1, Hydraulic fluid power Flange connectors with split or one-piece flange clamps and metric or inch screws Part 1: Flange connectors, ports and mounting surfaces for use at pressures of 3,5 MPa (35 bar) to 35 MPa (350 bar), DN 13 to DN 1273 Terms and definitionsFor the pur

25、poses of this document, the terms and definitions given in ISO 5598 apply.4 Dimensions4.1 Mounting dimensions for cylinders manufactured in accordance with this part of ISO 6020 shall be selected from Tables 1 to 9. Figures 1 to 9 show the mounting styles and relevant dimensions.1) 1 bar = 0,1 MPa =

26、 105 Pa; 1 MPa = 1 N/mm2.INTERNATIONAL STANDARD ISO 6020-3:2015(E) ISO 2015 All rights reserved 1BS ISO 6020-3:2015ISO 6020-3:2015(E)4.2 Tolerances for mounting dimensions shall be in accordance with Table 10.5 Bore sizesThe following bore sizes, in millimetres, are included in this compact series:2

27、50 320 3602) 400 5006 Piston stroke tolerancesThe tolerance on piston strokes shall be as follows: piston strokes 1 250 mm: +2/-0 mm; piston strokes 1 250 mm and 3 150 mm: +5/0 mm; piston strokes 3 150 mm and 8 000 mm: +8/0 mm.7 Mounting stylesThis part of ISO 6020 includes the following mounting st

28、yles, in accordance with ISO 6099: ME 11 Head, square flange (see Figure 2 and Table 2); ME 12 Cap, square flange (see Figure 3 and Table 3); MP 1 Cap, fixed clevis (see Figure 4 and Table 4); MP 3 Cap, fixed eye (see Figure 5 and Table 5); MP 5 Cap, fixed eye with spherical plain bearing (see Figur

29、e 6 and Table 6); MT 1 Head, integral trunnion (male) (see Figure 7 and Table 7); MT 2 Cap, integral trunnion (male) (see Figure 8 and Table 8); MT 4 Intermediate trunnion (male) with selectable position (see Figure 9 and Table 9).8 Piston rod characteristics8.1 This part of ISO 6020 covers piston r

30、ods that have a shouldered male thread end (see Figure 1 and Table 1 for basic dimensions).8.2 For rod end types, see ISO 4395.9 Identification statement (reference to this part of ISO 6020)It is strongly recommended for fabricators who elect to conform to this part of ISO 6020 to use the following

31、statement in test reports, catalogues, and sales literature:“Interchangeable hydraulic cylinder mounting dimensions selected in accordance with ISO 6020-3:2015, Hydraulic fluid power Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series Part 3: Compact series with bores from 250 mm t

32、o 500 mm”.2) Non-preferred size.2 ISO 2015 All rights reservedBS ISO 6020-3:2015ISO 6020-3:2015(E)EE AMMKKFFFigure 1 General dimensionsTable 1 General dimensions and part sizesDimensions in millimetresBoreRodaMMKK A E FFb6g max. max. 250140 M100 3 112320 DN 51180 M125 4 125320180 M125 4 125400 DN 64

33、220 M160 4 160360c180 M125 4 125450 DN 64250 M180 4 180400220 M160 4 160500 DN 64280 M200 4 200500280 M200 4 200630 DN 64360 M250 6 250aOther piston rod sizes that appear in ISO 3320 may be used.bSee ISO 61621 for flange port dimensions.c360 mm bore is a non-preferred size. ISO 2015 All rights reser

34、ved 3BS ISO 6020-3:2015ISO 6020-3:2015(E)R TF UG R TF UG RD RD - 0,5FVL WF ZB +FB Figure 2 ME 11 Head mounting, square flangeTable 2 Dimensions of head mountings, square flangeDimensions in millimetresBoreRodaMMRD TF FBdR WF F VL UG ZBbf8 js13 H13 js13 2 max. min. max. 250140280 380 30 235 110 75 5

35、445 460180320180325 472 36 283 110 75 5 549 520220360c180350 528 39 305 110 75 5 611 575250400220380 588 45 340 110 75 5 683 625280500280490 740 56 425 110 75 5 858 775360aOther piston rod sizes that appear in ISO 3320 may be used.bTolerance on dimension, ZB, is dependent on stroke (see Table 10).c3

36、60 mm bore is a non-preferred size.dHole in accordance with ISO 273, medium.4 ISO 2015 All rights reservedBS ISO 6020-3:2015ISO 6020-3:2015(E)RTFUGRTFUGFB ZJ +Figure 3 ME 12 Cap mounting, square flangeTable 3 Dimensions of cap mountings, square flangeDimensions in millimetresBoreRodaMMTF FBdR ZJbUGj

37、s13 H13 js13 max.250140380 30 235 420 445180320180472 36 283 475 549220360c180528 39 305 530 611250400220588 45 340 580 683280500280740 56 425 710 858360aOther piston rod sizes that appear in ISO 3320 may be used.bTolerance on dimension, ZJ, is dependent on stroke (see Table 10).c360 mm bore is a no

38、n-preferred size.dHole in accordance with ISO 273, medium. ISO 2015 All rights reserved 5BS ISO 6020-3:2015ISO 6020-3:2015(E)CBUBCDLXC +MRFigure 4 MP 1 Cap mounting, fixed clevisTable 4 Dimensions of cap mountings, fixed clevisDimensions in millimetresBoreRodaMMCB CD MR L XCbUBA16 H9 max. min. max.2

39、5014090 90 100 125 545 180180320180110 110 120 152 627 220220360c180125 125 140 175 705 250250400220140 140 160 195 775 280280500280180 180 200 250 960 360360aOther piston rod sizes that appear in ISO 3320 may be used.bTolerance on dimension, XC, is dependent on stroke (see Table 10).c360 mm bore is

40、 a non-preferred size.6 ISO 2015 All rights reservedBS ISO 6020-3:2015ISO 6020-3:2015(E)CDLXC +MREWFigure 5 MP 3 Cap mounting, fixed eyeTable 5 Dimensions of cap mountings, fixed eyeDimensions in millimetresBoreRodaMMEW CD MR L XCbh14 H9 max. min. 25014090 90 100 125 545180320180110 110 120 152 6272

41、20360c180125 125 140 175 705250400220140 140 160 195 775280500280180 180 200 250 960360aOther piston rod sizes that appear in ISO 3320 may be used.bTolerance on dimension, XC, is dependent on stroke (see Table 10).c360 mm bore is a non-preferred size. ISO 2015 All rights reserved 7BS ISO 6020-3:2015

42、ISO 6020-3:2015(E)CXLTXO +MSZZEPEXFigure 6 MP 5 Cap mounting, fixed eye with spherical plain bearingTable 6 Dimensions of cap mountings, fixed eye with spherical plain bearingDimensions in millimetresBoreRodaMMEP EX CX MS LT XObTilting angle Zmax.0 0,25max. min. min.250140102 125 1250 0,025160 160 5

43、804180320180130 160 1600 0,025200 200 675220360c180130 160 1600 0,025200 200 730250400220162 200 2000 0,030250 250 830280500280192 250 2500 0,035320 320 1 030360aOther piston rod sizes that appear in ISO 3320 may be used.bTolerance on dimension, XO, is dependent on stroke (see Table 10).c360 mm bore

44、 is a non-preferred size.8 ISO 2015 All rights reservedBS ISO 6020-3:2015ISO 6020-3:2015(E)TDTL TC TL(UT)XGZB +Figure 7 MT 1 Head mounting, integral trunnion (male)Table 7 Dimensions of head mountings, integral trunnion (male)Dimensions in millimetresBoreRodaMMTC UT TD XG TL ZBbh14 ref. f8 2 js13 25

45、0140320 520 125 178 100 505180320180400 650 160 195 125 580220360c180450 740 180 205 145 640250400220500 820 200 215 160 685280500280630 1030 250 240 200 825360aOther piston rod sizes that appear in ISO 3320 may be used.bTolerance on dimension, ZB, is dependent on stroke (see Table 10).c360 mm bore

46、is a non-preferred size. ISO 2015 All rights reserved 9BS ISO 6020-3:2015ISO 6020-3:2015(E)TDTL TC TL(UT)XJ +ZB +Figure 8 MT 2 Cap mounting, integral trunnion (male)Table 8 Dimensions of cap mountings, integral trunnion (male) Dimensions in millimetresBoreRodaMMTC UT TD XJbTL ZBbh14 ref. f8 js13 250

47、140320 520 125 393 100 505180320180400 650 160 450 125 580220360c180450 740 180 500 145 640250400220500 820 200 525 160 685280500280630 1030 250 615 200 825360aOther piston rod sizes that appear in ISO 3320 may be used.bTolerances on dimensions, XJ and ZB, are dependent on stroke (see Table 10).c360

48、 mm bore is a non-preferred size.10 ISO 2015 All rights reservedBS ISO 6020-3:2015ISO 6020-3:2015(E)XVZB +(UM)TM TLTLUWTDFigure 9 MT 4 Mounting with intermediate trunnion (male) with selectable positionTable 9 Dimensions of mountings with intermediate trunnion (male) with selectable positionDimensio

49、ns in millimetresBoreRodaMMUW TM UM TD XV ZBbTLmax. h14 ref. f8 js13250140480 380 580 125variabled460 100180320180600 485 735 160 520 125220360c180675 545 835 180 575 145250400220750 605 925 200 625 160280500280945 745 1145 250 775 200360aOther piston rod sizes that appear in ISO 3320 may be used.bTolerance on dimension, ZB, is dependent on stroke (see Table 10