BS ISO 3438-2013 Subland twist drills for holes prior to tapping screw threads《螺纹攻丝前钻孔用阶梯麻花钻》.pdf

《BS ISO 3438-2013 Subland twist drills for holes prior to tapping screw threads《螺纹攻丝前钻孔用阶梯麻花钻》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 3438-2013 Subland twist drills for holes prior to tapping screw threads《螺纹攻丝前钻孔用阶梯麻花钻》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 3438:2013Subland twist drills for holesprior to tapping screw threadsBS ISO 3438:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of IS

2、O 3438:2013. Itsupersedes BS ISO 3438:2003 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee MTE/18, Tools tips and inserts for cutting applications.A list of organizations represented on this committee can beobtained on request to its secretary.This publ

3、ication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 77002 9ICS 25.100.30Compliance with a British Standard cannot confer immunity

4、fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 June 2013.Amendments issued since publicationDate Text affectedBS ISO 3438:2013 ISO 2013Subland twist drills for holes prior to tapping screw threadsForets tags pour avan

5、t-trous de taraudageINTERNATIONAL STANDARDISO3438Third edition2013-05-01Reference numberISO 3438:2013(E)BS ISO 3438:2013ISO 3438:2013(E)ii ISO 2013 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2013All rights reserved. Unless otherwise specified, no part of this publication may be reproduced o

6、r utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO co

7、pyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 3438:2013ISO 3438:2013(E) ISO 2013 All rights reserved iiiContents PageForeword iv1 Scope . 12 Normative references 13 Dimensions . 13.1 Gene

8、ral . 13.2 Subland twist drills with Morse taper shank 13.3 Subland twist drill with cylindrical shank 2Annex A (informative) Relationship between the symbols of this International Standard and the ISO 13399 series . 4Bibliography 5BS ISO 3438:2013ISO 3438:2013(E)ForewordISO (the International Organ

9、ization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been establish

10、ed has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.

11、International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publ

12、ication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent r

13、ights.ISO 3438 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 2, High speed steel cutting tools and their attachments.This third edition cancels and replaces the second edition (ISO 3438:2003), of which it constitutes a minor revision with the following changes: merging

14、of ISO 3438:2003 and ISO 3439:2003 into a single standard; adding of an informative annex giving the relationship between the symbols of this document and the symbols according to the ISO 13399 series.iv ISO 2013 All rights reservedBS ISO 3438:2013INTERNATIONAL STANDARD ISO 3438:2013(E)Subland twist

15、 drills for holes prior to tapping screw threads1 ScopeThis International Standard specifies the dimensions of subland twist drills with Morse taper shanks and cylindrical shanks for holes prior to tapping screw threads.The drills are designed to produce holes prior to tapping metric threads (coarse

16、 pitch series) over a selected range of: M8 to M30 for subland twist drills with Morse taper shanks; M3 to M14 for subland twist drills with cylindrical shanks.This International Standard complements ISO 2306.The relationship between the symbols of this International Standard and those according to

17、the ISO 13399 series is given for information in Annex A.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest

18、 edition of the referenced document (including any amendments) applies.ISO 296, Machine tools Self-holding tapers for tool shanksISO 2768-1, General tolerances Part 1: Tolerances for linear and angular dimensions without individual tolerance indicationsISO 10899:1996, High-speed steel two-flute twis

19、t drills Technical specifications3 Dimensions3.1 GeneralAll dimensions and tolerances are given in millimetres. Tolerances not specified shall be of tolerance class “c” in accordance with ISO 2768-1.3.2 Subland twist drills with Morse taper shankThe dimensions for subland twist drills with Morse tap

20、er shanks shall be in accordance with the dimensions shown in Figure 1 and given in Table 1. ISO 2013 All rights reserved 1BS ISO 3438:2013ISO 3438:2013(E)aOptional recess.bMorse taper in accordance with ISO 296, but with a cone tolerance as defined in ISO 10899:1996, 5.3, and Annex A.Figure 1 Subla

21、nd twist drill with Morse taper shankTable 1 Dimensions of subland twist drill with Morse taper shank prior to tapping metric screw threadsd1h8d2h8l1l2l3Morse taper No.Thread6,8 9 162 81 211M8 1,258,5 11 175 94 25,5 M10 1,510,2 13,5 189 108 30 M12 1,7512 15,5 218 120 34,52M14 214 17,5 228 130 38,5 M

22、16 215,5 20 238 140 43,5 M18 2,517,5 22 248 150 47,5 M20 2,519,5 24 281 160 51,53M22 2,521 26 286 165 56,5 M24 324 30 296 175 62,5 M27 326,5 33 334 185 70 4 M30 3,53.3 Subland twist drill with cylindrical shankThe dimensions for subland twist drills with cylindrical shanks shall be in accordance wit

23、h the dimensions shown in Figure 2 and given in Table 2.aOptional recess.Figure 2 Subland twist drill with cylindrical shank2 ISO 2013 All rights reservedBS ISO 3438:2013ISO 3438:2013(E)Table 2 Dimensions of subland twist drill with cylindrical shank prior to tapping metric screw threadsd1h8d2h8l1l2

24、l3Thread2,5 3,4 70 39 8,8 M3 0,53,3 4,5 80 47 11,4 M4 0,74,2 5,5 93 57 13,6 M5 0,85 6,6 101 63 16,5 M6 16,8 9 125 81 21 M8 1,258,5 11 142 94 25,5 M10 1,510,2 13,5 160 108 30 M12 1,7512 15,5 178 120 34,5 M14 2 ISO 2013 All rights reserved 3BS ISO 3438:2013ISO 3438:2013(E)Annex A (informative) Relatio

25、nship between the symbols of this International Standard and the ISO 13399 seriesA.1 Relationship between symbolsFor the relationship between the symbols of this International Standard and symbols according to the ISO 13399 series, see Table A.1.Table A.1 Relationship between symbols in this Interna

26、tional Standard and the ISO 13399 seriesSymbol in ISO 3438 (this International Standard)Reference in ISO 3438 (this International Standard)Property name in the ISO 13399 seriesSymbol in the ISO 13399 seriesISO 13399 series BSU coded1Figures 1 and 2Cutting diam-eterDCONISO/TS 13399-3 71CF29862B277d2F

27、igures 1 and 2Cutting diam-eterDCONISO/TS 13399-3 71CF29862B277l1Figures 1 and 2 Overall length OALISO/TS 13399-3 71D078EB7C086l2Figures 1 and 2Length chip fluteLCFISO/TS 13399-3 71DCD39338974l3Figures 1 and 2Step diameter lengthSDLISO/TS 13399-3 71D078F5BEDBE4 ISO 2013 All rights reservedBS ISO 343

28、8:2013ISO 3438:2013(E)Bibliography1 ISO 13399-1, Cutting tool data representation and exchange Part 1: Overview, fundamental principles and general information model2 ISO/TS 13399-2, Cutting tool data representation and exchange Part 2: Reference dictionary for the cutting items3 ISO/TS 13399-3, Cut

29、ting tool data representation and exchange Part 3: Reference dictionary for tool items4 ISO/TS 13399-4, Cutting tool data representation and exchange Part 4: Reference dictionary for adaptive items5 ISO/TS 13399-5, Cutting tool data representation and exchange Part 5: Reference dictionary for assemb

30、ly items6 ISO 13399-50, Cutting tool data representation and exchange Part 50: Reference dictionary for reference systems and common concepts7 ISO 13399-60, Cutting tool data representation and exchange Part 60: Reference dictionary for connection systems8 ISO 13399-100, Cutting tool data representa

31、tion and exchange Part 100: Definitions, principles and methods for reference dictionaries9 ISO 13399-150, Cutting tool data representation and exchange Part 150: Usage guidelines ISO 2013 All rights reserved 5BS ISO 3438:2013ISO 3438:2013(E) ISO 2013 All rights reservedICS 25.100.30Price based on 5

32、 pagesThis page deliberately left blankBSI is the independent national body responsible for preparing British Standards and other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. BSI is incorporated by Royal Char

33、ter. British Standards and other standardisation products are published by BSI Standards Limited.British Standards Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards and PASs are periodically updated by amendment

34、 or revision. Users of British Standards and PASs should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using British Standards wo

35、uld inform the Secretary of the technical committee responsible, the identity of which can be found on the inside frontcover. Similary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers BSI Subscribing Members an individual updating service call

36、ed PLUS which ensures that subscribers automatically receive the latest editions of British Standards and PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website add

37、ition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, BSI will supply the British Standard implementation of the relevant internati

38、onal standard, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: BSI Subscribing Members are kept up to date with standards

39、developments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards and PASs via British Standar

40、ds Online can be found at information about British Standards is available on the BSI website at www.bsi- the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that own copyright in the i

41、nformation used (such as the international standardisation bodies) has formally licensed such information to BSI for commerical publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any

42、form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Department.Tel: +44 (0)20 8996 7070Email: