BS ISO 1268-8-2004 Fibre-reinforced plastics - Methods of producing test plates - Compression moulding of SMC and BMC《纤维增强塑料 试验板的生产方法 SMC和BMC压模》.pdf

《BS ISO 1268-8-2004 Fibre-reinforced plastics - Methods of producing test plates - Compression moulding of SMC and BMC《纤维增强塑料 试验板的生产方法 SMC和BMC压模》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 1268-8-2004 Fibre-reinforced plastics - Methods of producing test plates - Compression moulding of SMC and BMC《纤维增强塑料 试验板的生产方法 SMC和BMC压模》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS ISO 1268-8:2004 Fibre-reinforced plastics Methods of producing test plates Part 8: Compression moulding of SMC and BMC ICS 83.120 BS ISO 1268-8:2004 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 2 June 2004 BSI 2 June 20

2、04 ISBN 0 580 43836 8 National foreword This British Standard reproduces verbatim ISO 1268-8:2004 and implements it as the UK national standard. The UK participation in its preparation was entrusted to Technical Committee PRI/42, Fibre reinforced thermosetting plastics and prepregs, which has the re

3、sponsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international publications referred to in this document may be found in the BSI Catalogue under the section entitled “Internation

4、al Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British

5、Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and Eu

6、ropean developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the ISO title page, pages ii to v, a blank page, pages 1 to 8, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when t

7、he document was last issued. Amendments issued since publication Amd. No. Date Comments Reference number ISO 1268-8:2004(E)INTERNATIONAL STANDARD ISO 1268-8 First edition 2004-05-15 Fibre-reinforced plastics Methods of producing test plates Part 8: Compression moulding of SMC and BMC Plastiques renf

8、orcs de fibres Mthodes de fabrication de plaques dessai Partie 8: Moulage par compression des SMC et BMC BSISO12688:2004IS-8621 O8:(4002E) DPlcsid Fremia ihTs PDF file may ctnoian emdebt dedyfepcaes. In ccaocnadrw eith Aebods licensilop gnic,y this file mairp eb ynted iv roweb detu slahl ton ide ebt

9、lnu deess the typefaces whice era hml era deddebicsnede to i dnanstlaled t noeh computfrep reormign tide ehtin.g In wodlnidaot gnhis file, trapise atpecc tiereht nser ehnopsiiblity fo not infriigngn Aebods licensilop gnic.y ehT ISO tneClar Secrteiraat caceptl on siibality in this .aera Ai ebods a tr

10、edamafo kr Aebod SystemI sncotaropr.de teDails fo teh softwacudorp erts sut deo crtaee this PDF file cna f ebi dnuon tlareneG eh Info leratit evo the file; tP ehDc-Frtaeion marapterew setpo erimizde for irpnti.gn Evyre caer neeb sah taken to sneeru that the file is suitlbae fosu re yb ISO memdob reb

11、eis. In tlnu ehikletneve y ttah lborp aem leratit gno it is f,dnuo plsaee inform ttneC ehlar Secrteiraat ta the serddaig sleb nevwo. ii BSISO12688:2004 iiiContents Page Foreword iv Introduction v 1 Scope 1 2 Normative references . 1 3 Terms and definitions. 1 4 Health and safety 1 5 Plate dimensions

12、. 2 6 Apparatus. 2 7 Sampling and conditioning 2 8 Procedure. 3 9 Stabilization . 4 10 Test plate preparation report . 5 Annex A (informative) Applicable test methods 6 Bibliography . 8 BSISO12688:2004iv Foreword ISO (the International Organization for Standardization) is a worldwide federation of n

13、ational standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Inter

14、national organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the

15、 rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by

16、 at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 1268-8 was prepared by Technical Committee IS

17、O/TC 61, Plastics, Subcommittee SC 13, Composites and reinforcement fibres. Together with the other parts (see below), this part of ISO 1268 cancels and replaces ISO 1268:1974, which has been technically revised. ISO 1268 consists of the following parts, under the general title Fibre-reinforced plas

18、tics Methods of producing test plates: Part 1: General conditions Part 2: Contact and spray-up moulding Part 3: Wet compression moulding Part 4: Moulding of prepegs Part 5: Filament winding Part 6: Pultrusion moulding Part 7: Resin transfer moulding Part 8: Compression moulding of SMC and BMC Part 9

19、: Moulding of GMT/STC Part 10: Injection moulding of BMC and other long-fibre moulding compounds General principles and moulding of multipurpose test specimens Part 11: Injection moulding of BMC and other long-fibre moulding compounds Small plates BSISO12688:2004 vIntroduction Compression moulding o

20、f SMC and BMC differs from that of all other compression-mouldable reinforced thermosetting materials. Because of the maturation process which typically takes place before moulding and the ability of the compound to flow during moulding, special procedures need to be used for the production of test

21、plates from these compounds. Two different methods are given for preparing the mould charge: method A for moulding without the material flowing in the mould and method B for moulding so that the material flows in the mould. For engineers designing new moulds, knowledge of the anisotropy imparted to

22、the moulding under defined moulding conditions is essential. It is therefore necessary for the test plates from which test specimens will be cut to be manufactured under comparable conditions. BSISO12688:2004blankINTENRATIONAL TSANDADR IS-8621 O8:(4002E)1Fibre-reinforced plastics Methods of producin

23、g test plates Part 8: Compression moulding of SMC and BMC 1 Scope This part of ISO 1268 specifies the general principles and procedures for the compression moulding of test plates from two types of fibre-reinforced thermosetting moulding compound: sheet moulding compound (SMC) and bulk moulding comp

24、ound (BMC). The aim of this part of ISO 1268 is to ensure the preparation of flat test plates from which test specimens can be cut (for the relevant test methods, see Annex A). The plates are produced in such a way that specimens cut from them give representative results when used in these test meth

25、ods. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 472, Plastics Voc

26、abulary ISO 8604, Plastics Prepregs Definitions of terms and symbols for designations ISO 12115:1997, Fibre-reinforced plastics Thermosetting moulding compounds and prepregs Determination of flowability, maturation and shelf life EN 1842, Plastics Thermoset moulding compounds (SMC - BMC) Determinati

27、on of compression moulding shrinkage 3 Terms and definitions For the purposes of this part of ISO 1268, the terms and definitions given in ISO 472 and ISO 8604, together with the the following, apply. 3.1 compression time time during which the required pressure is applied to the mould 4 Health and s

28、afety This part of ISO 1268 is limited to describing test plate preparation methods. The conditions under which the materials used are handled shall comply with the national regulations in force in each country and the staff shall be informed of the hazards involved and appropriate precautions taken

29、. BSISO12688:20042 5 Plate dimensions The recommended moulded-plate size is 200 mm 590 mm (necessary for method II in ISO 12115:1997). If no suitable mould is available, use a mould with a minimum area of 300 cm 2to make plates by method A only, the dimensions of the mould being such that at least f

30、ive test specimens measuring 20 mm 250 mm can be cut from the plates. Most of the methods of test for SMC and BMC require a test specimen thickness of about 4 mm. In special cases, test plates of other thicknesses will have to be moulded. For particular test methods, the moulded plate specified in E

31、N 1842 could be used. 6 Apparatus 6.1 Press Test plates may be moulded on any hydraulic moulding press which complies with the following requirements: it is capable of closing the mould and applying the specified moulding pressure within a maximum of 15 s; it is capable of maintaining the specified

32、pressure to within 5 % during the compression time. 6.2 Mould The mould used shall be able to withstand the specified temperature and pressure. The mould design shall ensure that the entire force is applied to the moulding material. The mould cavity shall be flat and have an area of at least 300 cm

33、2for method A or 200 mm 590 mm for method B. 6.3 Cooling rack A device or fixture shall be used to hold the test plates while they cool. A non-metallic cooling rack with slots to hold the plates in a vertical position spaced at least 20 mm apart is recommended. The ends of the plates should preferab

34、ly be protected from damage. To ensure symmetrical cooling of all test plates, the outer plates shall be protected by additional protective plates. 7 Sampling and conditioning 7.1 With SMC, take the sample from the full width of the roll. Trim 5 cm off both sides of the sample to eliminate edge effe

35、cts resulting from the manufacturing process. 7.2 With BMC, take a sample representative of the material from a production batch. 7.3 Immediately after sampling, protect the material by placing it in a suitable bag to avoid loss of volatile constituents and absorption of moisture. Condition samples

36、to establish temperature equilibrium before moulding by placing them in a room at a temperature of (23 2) C. BSISO12688:2004 38 Procedure 8.1 Preparation of charge 8.1.1 Method A: For moulding without the material flowing in the mould With SMC, 100 % mould-surface coverage is recommended, but it sha

37、ll not be less than 90 % of the total cavity area unless otherwise specified or agreed between the interested parties. Prepare the SMC required to charge the mould by stacking the necessary number of layers. Note the sequence and orientation of the layers. If a mould coverage of less than 100 % is u

38、sed, reduce both the length and the width of the layers proportionately in order to prevent flow during moulding altering the orientation of the fibres. With BMC, pre-shape the moulding material manually on a flat tray to give a flat layer with as even a thickness as possible and of the same size as

39、 the mould cavity. 8.1.2 Method B: For moulding so that the material flows in the mould Prepare the charge as specified in method II of ISO 12115:1997 to give an initial mould-surface coverage of between 25 % and 30 % (see Figure 1). Dimensions in millimetres Key 1 charge Figure 1 Charge covering 25

40、 % to 30 % of total area of mould cavity 8.2 Moulding conditions The mould temperature shall be 140 C 2 C, unless otherwise specified or agreed. The moulding pressure and the compression time shall be as given in the relevant material specification. BSISO12688:20044 8.3 Moulding procedure 8.3.1 Set

41、the moulding conditions to those to be used. 8.3.2 Prepare the charge as described in 8.1.1 or 8.1.2 to obtain the specified test plate thickness. 8.3.3 Weigh the charge. 8.3.4 Load the charge into the mould cavity taking care that it is in the centre of the mould cavity, if applicable and close the

42、 press immediately. As soon as the specified pressure is reached, start measuring the compression time. 8.3.5 When the compression time is complete, open the press, remove the moulded plate and place it in the cooling rack to cool to room temperature. 8.3.6 Discard any defective plates. 8.3.7 Measur

43、e the thickness of each plate. 9 Stabilization It is recommended that, unless otherwise specified or agreed, the test plates are kept for 48 h at the ambient conditions in the laboratory before cutting the test specimens from them. When cutting test specimens from plates produced using charges prepa

44、red by method B, cut them as shown in Figure 2. Key 1 direction of flow 2 specimens perpendicular to direction of flow 3 specimens parallel to direction of flow 4 discard NOTE There is an end effect perpendicular to the direction of flow, so the left-hand end strip (4) has to be discarded. Any edge

45、effect in the corresponding area at the right-hand end of the plate is confined to the tab area of the test specimens and thus does not affect the value of the property measured. The edges parallel to the direction of flow do not exhibit significant edge effects, so do not need to be discarded. Figu

46、re 2 Areas of flow and directions in which specimens are cut from the moulded plate BSISO12688:2004 510 Test plate preparation report The test plate preparation report shall include the following information: a) a reference to this part of ISO 1268; b) a full description of the moulding material use

47、d, including at least the type, the source of supply, the manufacturers name and the designation of the material; c) the date of manufacture of the material; d) the type and size of mould used; e) a description of the charge (length, width, mass and number of layers for SMC, mass of charge for BMC);

48、 f) the moulding conditions (temperature, pressure, compression time); g) identification of the plates, using a suitable numbering or code system; h) the thickness of the plates; i) details of any incidents or modifications to the procedure which might influence the properties of test specimens take

49、n from the test plates. BSISO12688:20046 Annex A (informative) Applicable test methods Test specimens cut from of test plates prepared in accordance with this part of ISO 1268 can be used for the following test methods. This list is purely informative and will not be updated every time a test method is amended, revised or withdrawn. A.1 Mechanical properties ISO 179-1, Plastics Determination of C