BS EN ISO 14922-4-1999 Thermal spraying - Quality requirements of thermally sprayed structures - Elementary quality requirements《热喷涂 热喷涂结构件的质量要求 基本质量要求》.pdf

《BS EN ISO 14922-4-1999 Thermal spraying - Quality requirements of thermally sprayed structures - Elementary quality requirements《热喷涂 热喷涂结构件的质量要求 基本质量要求》.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 14922-4-1999 Thermal spraying - Quality requirements of thermally sprayed structures - Elementary quality requirements《热喷涂 热喷涂结构件的质量要求 基本质量要求》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN ISO 14922-4:1999 Thermal spraying Quality requirements of thermally sprayed structures Part 4: Elementary quality requirements The European Standard EN ISO 14922-4:1999 has the status of a British Standard ICS 25.220.20BSENISO14922-4:1999 This British Standard, having been pre

2、pared under the directionof the Sector Committeefor Materials and Chemicals, waspublished underthe authorityof the Standards Committee and comesinto effecton 15August1999 BSI 03-2000 ISBN 0 580 32445 1 National foreword This British Standard is the English language version of EN ISO 14922-4:1999. It

3、 is identical with ISO 14922-4:1999. The UK participation in its preparation was entrusted to Technical Committee STI/40, Thermally sprayed inorganic finishes, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enqui

4、ries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. The UK voted against EN I

5、SO 14922-4 on the grounds that the subject of that standard is already covered by the EN ISO 9000 series on quality management and quality assurance. However, as EN ISO 14922-4 achieved the requisite approval from amongst the other European members of CEN, the UK is under an obligation to implement

6、it as a British Standard. Cross-references Attention is drawn to the fact that CEN and CENELEC Standards normally include an annex which lists normative references to international publications with their corresponding European publications. The British Standards which implement international or Eur

7、opean publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the nec

8、essary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theE

9、N ISO title page, pages 2 to 6 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date CommentsBSENISO14922-4:1999 BSI 03

10、-2000 i Contents Page National foreword Inside front cover Foreword 2 Text of EN ISO 14922-4 3ii blankEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 14922-4 June 1999 ICS 25.220 Englishversion Thermal spraying Quality requirements of thermally sprayed structures Part 4: Elementary quality

11、requirements (ISO 14922-4:1999) Projection thermique Exigences qualit des constructions obtenues par projection thermique Partie 4: Exigences qualit lmentaires (ISO 14922-4:1999) Thermisches Spritzen Qualittsanforderungen an thermisch gespritzte Bauteile Teil 4: Elementar Qualittsanforderungen (ISO

12、14922-4:1999) This European Standard was approved by CEN on 19 February 1999. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibl

13、iographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility o

14、f a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, CzechRepublic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, No

15、rway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1999 CEN All rights of exploitation in any form and by any means reserved w

16、orldwide for CEN national Members. Ref. No. EN ISO 14922-4:1999 EENISO14922-4:1999 BSI 03-2000 2 Foreword The text of EN ISO 14922-4:1999 has been prepared by Technical Committee CEN/TC 240 “Thermal spraying and thermally sprayed coatings”, the secretariat of which is held by DIN, in collaboration w

17、ith Technical Committee ISO/TC 107 “Metallic and other inorganic coatings”. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 1999, and conflicting national standards shall be withdrawn at

18、the latest by December 1999. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, CzechRepublic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembou

19、rg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Contents Page Foreword 2 1 Scope 3 2 Normative references 3 3 Definitions 3 4 Contract and design review 3 4.1 General 3 4.2 Application Contract review 3 4.3 Application Design review 4 5 Sub-contracting 4 6 Perso

20、nnel for thermal spraying 4 6.1 General 4 6.2 Qualified thermal sprayer 4 6.3 Thermal spraying coordinator 4 7 Personnel for quality testing 4 7.1 General 4 7.2 Non-destructive testing 4 8 Equipment 4 8.1 Equipment for manufacturing 4 8.2 Health and safety and environmental aspects 4 9 Thermal spray

21、ing activities 4 10 Consumables for thermal spraying 4 11 Storage and handling of substrate materials 4 12 Thermal spraying related inspection and testing 5 12.1 Inspection and testing before thermal spraying 5 12.2 Inspection and testing after thermal spraying 5 13 Non-conformance and corrective ac

22、tions 5 14 Calibration 5 15 Identification and traceability 5 16 Quality records 5 Annex ZA (informative) Bibliography 6 Table ZA.1 List of ISO standards conforming tothe EN standards quoted in clause 2 6ENISO14922-4:1999 BSI 03-2000 3 1 Scope This standard specifies requirements so that: It is inde

23、pendent of the type of the thermally sprayed structure. It defines quality requirements for thermal spraying both in workshops and on site. It provides guidance for describing a manufacturers capability to produce thermally sprayed constructions to meet specified requirements. It may also be used as

24、 a basis for assessing the manufacturer in respect to his thermal spraying capability. This standard is appropriate when demonstration of a manufacturers capability to produce thermally sprayed construction, fulfilling specified quality requirements, are specified in one or more of the following: a

25、contract between involved parties; an application standard; a regulatory requirement. The requirements contained within this standard may be adopted in full or may be selectively deleted by the manufacturer if not applicable to the construction concerned. They provide a flexible framework for the co

26、ntrol of thermal spraying in the following cases: Case 1 To provide specific requirements for thermal spraying in contracts which require the manufacturer to have a quality system other than EN ISO 9001 or EN ISO 9002. Case 2 To provide specific requirements for thermal spraying in contracts which r

27、equire the manufacturer developing a quality system. Case 3 To provide specific requirements for thermal spraying in application standards which uses thermal spraying as part of its requirements or in a contract between relevant parties. 2 Normative references This European standard incorporates by

28、dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standa

29、rd only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 473, Non-destructive testing Qualification and certification of personnel. EN 582, Thermal spraying Determination of the adhesive tensile strength. EN 657, T

30、hermal spraying terminology Classification. EN 1274, Thermal spraying Powders Composition Technical supply conditions. EN ISO 9001, Quality systems Model for quality assurance in design/development, production, installation and servicing. (ISO 9001:1994) EN ISO 9002, Quality systems Model for qualit

31、y assurance in production, installation and servicing. (ISO 9002:1994) prEN ISO 14919, Thermal spraying Wires, rods and cords for flame and arc spraying Classification Technical supply conditions. EN ISO 14922-1, Quality requirements of thermally sprayed structures Part 1: Guidelines for selection a

32、nd use. ISO 8402:1994, Quality management and quality assurance Vocabularity. 3 Definitions For the purposes of this standard definitions given in EN 657 and listed in part 1 of this standard apply. 4 Contract and design review 4.1 General The manufacturer shall review the contractual requirements a

33、nd the design data provided by the purchaser or in-house data for construction designed by the manufacturer. This is to ensure that all information necessary to carry out the fabrication operations is available prior to the commencement of the work. The manufacturer shall affirm his capability to me

34、et all thermal spraying contract requirements and ensure adequate planning of all quality related activities. 4.2 Application Contract review Contractual requirements to be considered should include: a) the application standard to be used, together with any supplementary requirements; b) inspection

35、and testing; c) final testing; d) environmental conditions relevant to thermal spraying on site; e) sub-contracting, f) handling of non-conformance.ENISO14922-4:1999 4 BSI 03-2000 4.3 Application Design review Design requirements to be considered should include: a) location, accessibility and sequen

36、ce of all coatings; b) surface finish of the coating; c) substrate material specification and coating properties; d) dimensions and details of prepared substrate surfaces and sprayed coatings; e) quality and acceptance requirements for coatings. 5 Sub-contracting Any sub-contractor shall work under

37、the order and responsibility of the manufacturer and shall fully comply with the relevant requirements of this standard. 6 Personnel for thermal spraying 6.1 General The manufacturer shall have at his disposal sufficient and competent personnel for the planning, performing, supervising and examining

38、 of the thermal spraying production according to specified requirements. 6.2 Qualified thermal sprayer The entire personnel for thermal spraying must be introduced/instructed. 6.3 Thermal spraying coordinator The manufacturer shall have at his disposal personnel who controls the correct performing o

39、f the thermal spraying work. 7 Personnel for quality testing 7.1 General The manufacturer shall have at his disposal sufficient and competent personnel for performing the quality testing. 7.2 Non-destructive testing The non-destructive testing personnel should be approved according to EN 473. 8 Equi

40、pment 8.1 Equipment for manufacturing The following equipment shall be available when necessary: workshops, generally as roofed working sites; stores for correct storage of substrate materials (to be coated components), consumables and other additives for thermal spraying; equipment for drying spray

41、 powders; equipment and machines to prepare and machine the components for thermal spraying (e.g. degreasing equipment, sand blasting cabins); spraying equipment, including equipment for supply, setting and control; handling systems (e.g. turntables, turning machines, robot systems); exaust systems,

42、 dust filters, protective means against noise and radiation; equipment for thermal treatment of the components before and after spraying; cooling equipment; machines, tools and equipment for post treatment of thermal sprayed coatings (e.g.grinding, turning). 8.2 Health and safety and environmental a

43、spects Equipment necessary for health and safety and environmental protection must be available. All necessary activities to assure standards of health and safety and of emission have to be conducted. 9 Thermal spraying activities Thermal spraying shall be performed in accordance with an appropriate

44、 spraying procedure. 10 Consumables for thermal spraying Responsibilities and procedures involved in the control of thermal spraying consumables shall be specified by the manufacturer. 11 Storage and handling of substrate materials Storage shall be such that the material will not be adversely affect

45、ed. Identification shall be maintained during storage.ENISO14922-4:1999 BSI 03-2000 5 12 Thermal-spraying related inspection and testing 12.1 Inspection and testing before thermal spraying Before the start of thermal spraying, the following shall be checked, when necessary: suitability and validity

46、of the thermal sprayers certificate; suitability of thermal spraying procedure specification; identify of the substrate material; identify of the consumables, e.g. according to EN 1274; surface preparation, also shape and dimension; fit-up, jigging and tacking; any special requirements in thermal sp

47、raying procedure specification, e.g. prevention of distortion; arrangement of any production test; suitability of working conditions for thermal spraying, including environment. 12.2 Inspection and testing after thermal spraying After thermal spraying, the compliance with relevant acceptance criteri

48、a shall be checked, when necessary. 13 Non-conformance and corrective actions Measures shall be implemented to control items which do not conform to specified requirements in order to prevent their inadvertent use. When repair and/or thermal re-spraying is undertaken by the manufacturer, appropriate

49、 procedures shall be available at all workstations where these activities are performed. When repair or thermal respraying is performed, the items shall be re-inspected, tested and examined in accordance with the original requirements. Measures shall also be implemented to ensure that conditions adverse to quality of the thermally sprayed construction are promptly identified and corrected. 14 Calibration The manufacturer shall be responsible for t