BS EN 61196-10-1-2014 Coaxial communication cables Blank detail specification for semi-rigid cables with polytetrafluoroethylene (PTFE) dielectric《同轴通信电缆 带有聚四氟乙烯 (PTFE) 介质的半刚性电缆的详细.pdf

《BS EN 61196-10-1-2014 Coaxial communication cables Blank detail specification for semi-rigid cables with polytetrafluoroethylene (PTFE) dielectric《同轴通信电缆 带有聚四氟乙烯 (PTFE) 介质的半刚性电缆的详细.pdf》由会员分享，可在线阅读，更多相关《BS EN 61196-10-1-2014 Coaxial communication cables Blank detail specification for semi-rigid cables with polytetrafluoroethylene (PTFE) dielectric《同轴通信电缆 带有聚四氟乙烯 (PTFE) 介质的半刚性电缆的详细.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationCoaxial communication cablesPart 10-1: Blank detail specificationfor semi-rigid cables with polytetrafluoroethylene (PTFE) dielectricBS EN 61196-10-1:2014National forewordThis British Standard is the UK implementation of EN 61196-10-1:2014. It isidentical to IEC 61196-10-1:2

2、014. The UK participation in its preparation was entrusted to TechnicalCommittee EPL/46, Cables, wires and waveguides, radio frequency connectors and accessories for communication and signalling.A list of organizations represented on this committee can be obtained onrequest to its secretary.This pub

3、lication does not purport to include all the necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2014.Published by BSI Standards Limited 2014ISBN 978 0 580 80685 8ICS 33.120.10Compliance with a British Standard cannot confer immunit

4、y fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 November 2014.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 61196-10-1:2014EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN

5、61196-10-1 November 2014 ICS 33.120.10 English Version Coaxial communication cables - Part 10-1: Blank detail specification for semi-rigid cables with polytetrafluoroethylene (PTFE) dielectric (IEC 61196-10-1:2014) Cbles coaxiaux de communication - Partie 10-1: Spcification particulire-cadre relativ

6、e aux cbles semi-rigides comportant un dilectrique polyttrafluorothylne (PTFE) (CEI 61196-10-1:2014) Koaxiale Kommunikationskabel - Teil 10-1: Vordruck fr Bauartspezifikation fr halb-starre Kabel mit Polytetrafluorethylen- (PTFE-)Isolation (IEC 61196-10-1:2014) This European Standard was approved by

7、 CENELEC on 2014-10-30. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national st

8、andards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own lang

9、uage and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, Fran

10、ce, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Nor

11、malisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN 61196-10-1:2014 E BS EN 61196-10-1:20

12、14EN 61196-10-1:2014 - 2 - Foreword The text of document 46A/1214/FDIS, future edition 1 of IEC 61196-10-1, prepared by SC 46A “Coaxial cables“ of IEC/TC 46 “Cables, wires, waveguides, R.F. connectors, R.F. and microwave passive components and accessories“ was submitted to the IEC-CENELEC parallel v

13、ote and approved by CENELEC as EN 61196-10-1:2014. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2015-07-30 latest date by which the national standards conflicting with

14、 the document have to be withdrawn (dow) 2017-10-30 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the

15、 International Standard IEC 61196-10-1:2014 was approved by CENELEC as a European Standard without any modification. BS EN 61196-10-1:2014- 3 - EN 61196-10-1:2014 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following docu

16、ments, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 When an Internatio

17、nal Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu Publication Year Title EN/HD Year IEC 61196-1 2005 Coaxial

18、communication cables - Part 1: Generic specification - General, definitions and requirements - - IEC 61196-10 2014 Coaxial communication cables - Part 10: Sectional specification for semi-rigid cables with polytetrafluoroethylene (PTFE) dielectric - - BS EN 61196-10-1:2014 2 IEC 61196-10-1:2014 IEC

19、2014 CONTENTS 1 Scope 5 2 Normative references 5 3 Guidance for the preparation of detail specifications 5 4 Blank detail specification . 6 Annex A (normative) Maximum attenuation 9 BS EN 61196-10-1:2014IEC 61196-10-1:2014 IEC 2014 5 COAXIAL COMMUNICATION CABLES Part 10-1: Blank detail specification

20、 for semi-rigid cables with polytetrafluoroethylene (PTFE) dielectric 1 Scope This part of IEC 61196 applies to coaxial communication cables described in IEC 61196-10. It specifies the requirements for semi-rigid radio frequency and coaxial cables with solid dielectric and semi-airspace dielectric.

21、These cables are intended for use in microwave and wireless equipment or other signal transmission equipment or units at frequencies above 500 MHz. This part of IEC 61196 is to be read in conjunction with IEC 61196-1 and IEC 61196-10. The blank detail specification determines the layout and style fo

22、r detail. Detail specifications, based on the blank detail specification, may be prepared by a national organization, a manufacturer or a user. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application.

23、For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 61196-1:2005, Coaxial communication cables Part 1: Generic specification General, definitions and requirements IEC 61196-10:2014, Coaxia

24、l communication cables Part 10: Sectional specification for semi-rigid cables with polytetrafluoroethylene (PTFE) dielectric NOTE Documents which are needed to achieve the tests according to Clause 4, item 9 or item 10, respectively, are listed in IEC 61196-10. 3 Guidance for the preparation of deta

25、il specifications The detail specification shall be written in accordance with the layout of the blank detail specification, which forms part of this standard. NOTE 1 When a characteristic does not apply, then NA (for not applicable) is entered in the appropriate space. NOTE 2 When a characteristic

26、applies but a specific value is not considered necessary, then NS (for not specified) is entered. The numbers shown in brackets in this and the following pages correspond to the following items of required information, which should be entered in the space provided. 1 Name and address of the organiza

27、tion that has prepared the document 2 IEC document number and date of issue 3 Address of the organization from which the document is available 4 Related documents 5 Any other references to the cable, national reference, trade name, etc. 6 Complete description of the cable BS EN 61196-10-1:2014 6 IEC

28、 61196-10-1:2014 IEC 2014 7 Cable construction 8 Engineering information 9 Parameter to be verified 10 Reference to the relevant subclause of the sectional specification 11 Minimum requirements, the values entered shall meet as a minimum the requirements of sectional specification IEC 61196-10 12 Re

29、marks 4 Blank detail specification Title 1 Prepared by: 2 Document No.: Issue: Date: 3 Available from: 4 Generic specification IEC 61196-1 Sectional specification IEC 61196-10 5 Additional references: 6 Cable description: a) Cable variant b) Material of inner conductor c) Material of dielectric d) O

30、uter conductor e) Material of sheath (if any) 7 Cable construction: a) Inner conductor Material Diameter (mm) nominal Tolerance (mm): b) Dielectric Material Diameter (mm) nominal Tolerance (mm): c) Outer conductor Material Diameter (mm) nominal Tolerance (mm): . d) Sheath (if any) Material Minimum t

31、hickness (mm) Diameter (mm) Tolerance (mm): BS EN 61196-10-1:2014IEC 61196-10-1:2014 IEC 2014 7 8 Engineering information (reference only): a) Operating temperature range b) Installation temperature range c) Storage temperature range d) Maximum operating frequency e) Nominal characteristic impedance

32、 f) Maximum continue working voltage g) Minimum bending radius (static state) h) Minimum bending radius (dynamic state) i) Nominal weight j) Power rating 9 Parameter 10 Subclause of IEC 61196-10:2014 11 Value 12 Remarks Electrical characteristics 7.2 Continuity 7.2.1 pass Conductor direct current re

33、sistance 7.2.2 /km Withstand voltage of dielectric 7.2.3 kV r.m.s. 40 Hz to 60 Hz Withstand voltage of sheath 7.2.4 kV r.m.s. 40 Hz to 60 Hz Insulation resistance 7.2.5 M km 5 000 Mkm according to IEC 61196-10 Capacitance 7.2.6 Frequency: pF/m Mean characteristic impedance 7.2.7 ( ) 200 MHz Regulari

34、ty of impedance 7.2.8 Test procedure: Regularity 40 dB resp. 1 % aRelative propagation velocity (velocity ratio) 7.2.9 Frequency: ( ) % Return loss 7.2.10 at MHz dB If necessary, refer to a table or graph at the end of the detail specification Attenuation 7.2.11 at MHz dB/100 m If necessary, refer t

35、o a table or graph at the end of the detail specification Attenuation stability 7.2.12 Intermodulation (IM3) 7.2.13 dBm f1= MHz af2= MHz aInput power: W Only applicable to 50 cable variants Environmental characteristics 7.3 Dimensional stability 7.3.1 ns See IEC 61196-10 Heat behaviour 7.3.2 ns See

36、IEC 61196-10 BS EN 61196-10-1:2014 8 IEC 61196-10-1:2014 IEC 2014 Ageing 7.3.3 NS See IEC 61196-10 Solderability 7.3.4 NS See IEC 61196-10 Resistance to soldering 7.3.5 NS See IEC 61196-10 Mechanical characteristics 7.4 Visual examination 7.4.1 NS See IEC 61196-10 Dimensional examination 7.4.2 Ovali

37、ty of dielectric 7.4.3 % 7 % according to IEC 61196-10 Eccentricity of dielectric 7.4.4 % 10 % according to IEC 61196-10 Ovality of sheath 7.4.5 % 7 % according to IEC 61196-10 Adhesion testing 7.4.6 N Bendability (single bend) b7.4.7 1 cycle No cracks or longitudinal splits in outer conductor Trans

38、mission characteristics shall remain within specified tolerances Thermal cycling 7.4.8 Low temperature C min. High temperature C max. Rate of temperature change s Number of cycles Duration of cycle Details of sample placement Quality assessment Annex A NS See IEC 61196-10 NS: not specified, i.e. the

39、 appropriate requirement in the sectional specification shall apply. aMark NA, if not applicable bFrequencies are not always fixed frequencies and can be a swept over a range. BS EN 61196-10-1:2014IEC 61196-10-1:2014 IEC 2014 9 Annex A (normative) Maximum attenuation Frequency specified MHz Maximum

40、attenuation: dB/100 m at 20 C 200 800 1 000 _ BS EN 61196-10-1:2014This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Ch

41、arter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their

42、 combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve th

43、eir goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI

44、 publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services te

45、am.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from y

46、our desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an

47、updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you

48、 are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British