BS EN 61076-3-100-2000 Connectors for use in d c low-frequency analogue and digital high speed data applications - Part 3-100 Rectangular connectors with assessed quality - Details.pdf

《BS EN 61076-3-100-2000 Connectors for use in d c low-frequency analogue and digital high speed data applications - Part 3-100 Rectangular connectors with assessed quality - Details.pdf》由会员分享，可在线阅读，更多相关《BS EN 61076-3-100-2000 Connectors for use in d c low-frequency analogue and digital high speed data applications - Part 3-100 Rectangular connectors with assessed quality - Details.pdf（47页珍藏版）》请在麦多课文档分享上搜索。

1、Licensed Copy: Wang Bin, ISO/Exchange China Standards Information Centre, 28 December 2004, Uncontrolled Copy, (c) BSIBRITISH STANDARD BS EN 61076-3-100: 2000 Connectors for use in d.c., low-frequency analogue and digital high speed data applications Part 3-100: Rectangular connectors with assessed

2、quality Detail specification for a range of shielded connectors with trapezoidal-shaped shells and non-removable ribbon contacts on a 1,27 mm double row The European Standard EN 61076-3-100:2004 has the status of a British Standard ICS 31.220.10 Licensed Copy: Wang Bin, ISO/Exchange China Standards

3、Information Centre, 28 December 2004, Uncontrolled Copy, (c) BSIBS EN 61076-3-100:2000 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 20 October 2004 BSI 20 October 2004 ISBN 0 580 44621 2 National foreword This British Standard is the offic

4、ial English language version of EN 61076-3-100:2000. It is identical with IEC 61076-3-100:1999. The UK participation in its preparation was entrusted by Technical Committee EPL/48, Electromechanical components and mechanical structures for electronic equipment, to Subcommittee EPL/48/2, Connectors f

5、or electronic equipment, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international publications referred to in this document may be found in the BSI Catal

6、ogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its cor

7、rect application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests in

8、formed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 42, an inside back cover and a back cover. The BSI copyright notice displayed in this document i

9、ndicates when the document was last issued. Amendments issued since publication Amd. No. Date Comments Licensed Copy: Wang Bin, ISO/Exchange China Standards Information Centre, 28 December 2004, Uncontrolled Copy, (c) BSILicensed Copy: Wang Bin, ISO/Exchange China Standards Information Centre, 28 De

10、cember 2004, Uncontrolled Copy, (c) BSIPage2 EN610763100:2000Licensed Copy: Wang Bin, ISO/Exchange China Standards Information Centre, 28 December 2004, Uncontrolled Copy, (c) BSI-67016-3001 9991:CEI 3 CONTENTS Page FOWERODR. 7 Clause 1 General data.5 1.1 Recommended method of mounting.5 1.1.1 Minim

11、um and maximum number of contacts.5 1.2 Rating and characteristics5 1.3 Normative references 6 1.4 Marking .7 1.5 IEC type designation7 1.6 Ordering information9 2 Technical data 9 2.1 General .9 2.2 Survey of styles and variants .9 2.3 Information on application9 3 Dimensional information .9 3.1 Ge

12、neral .9 3.2 Isometric view and common features (with locking devices) .10 3.3 Mating information.10 3.3.1 Contact arrangements10 3.3.2 Mating face dimensions .12 3.3.3 Contact mating dimensions 14 3.4 Fixed connectors .14 3.4.1 Dimensions15 3.4.2 Terminations20 3.5 Free connectors 21 3.5.1 Dimensio

13、ns21 3.5.2 Termination .24 3.6 Accessories.24 3.7 Mounting information .24 3.7.1 Hole pattern on printed boards.24 3.7.2 Panel cutout dimensions 28 4 Characteristics29 4.1 Climatic category.29 4.2 Electrical .29 4.2.1 Creepage and clearance distance 29 4.2.2 Voltage proof .29 4.2.3 Current-carrying

14、capacity.29 4.2.4 Initial contact resistance 29 4.2.5 Initial insulation resistance.30 4.3 Mechanical30 4.3.1 Mechanical operation.30 4.3.2 Insertion and withdrawal forces30 Pa1eg E4002:001367016N Page3 EN610763100:2000 Licensed Copy: Wang Bin, ISO/Exchange China Standards Information Centre, 28 Dec

15、ember 2004, Uncontrolled Copy, (c) BSI-67016-3001 9991:CEI 5 Clause Page 5 Test schedule.31 5.1 General .31 5.2 Test schedules 32 5.2.1 Basic (minimum) test schedule.32 5.2.2 Full test schedule.32 6 Quality assessment procedures 38 6.1 Qualification approval testing.38 6.1.1 Method 1 .38 6.1.2 Metho

16、d 2 .39 6.2 Quality conformance inspection .39 6.2.1 Lot-by-lot tests.39 6.2.2 Periodic tests.39 6.3 Delayed delivery, re-inspection 40 Pa2eg E4002:001367016N Page4 EN610763100:2000 AnnexZ A( nroma)evitroN mevitar efercnese ot tniertannoia lbupcilatoisn wit hthrie corresdnopiE gnuroepap nublicatsnoi

17、 . 41 61076-3-100 IEC:1999 5 Clsua e Pa eg T 5es t scludehe.13 1.5Geenrla .13 T 2.5est scseludeh 23 B 1.2.5asic (minimum) tes tsceludeh.23 lluF 2.2.5 test scludehe.23 Q 6uytila assessmp tnerocuderse 83 Q 1.6ufilaci noita ppart lavoesnitg.83 dohteM 1.1.6 1 .83 dohteM 2.1.6 2 .93 Q 2.6uytila conformna

18、ci ensepcnoit .93 toL 1.2.6-by- toltests.93 P 2.2.6ericido tests.93 yaleD 3.6 de iledvery, re-insepcnoit 04 Pae2g N610763100:2004E P4ega E0002:001367016N nAnexZ A (norma)evitroN mevitar efercnese ot itnertannoia lbuplciatoisn wit htrieh corresdnopiuE gnroepap nublicatsnoi . 14 Annex ZA (normative) N

19、ormative references to international publications with their corresponding European publications . 41 Licensed Copy: Wang Bin, ISO/Exchange China Standards Information Centre, 28 December 2004, Uncontrolled Copy, (c) BSI-67016-3001 9991:CEI 11 CONNECTORS FOR USE IN DC, LOW-FREQUENCY ANALOGUE AND DIG

20、ITAL HIGH SPEED DATA APPLICATIONS Part 3-100: Rectangular connectors with assessed quality Detail specification for a range of shielded connectors with trapezoidal-shaped shells and non-removable ribbon contacts on a 1,27 mm double row 1 General data 1.1 Recommended method of mounting A complete con

21、nector consists of a fixed connector mounted vertically or at a right angle to the printed circuit board or panel mounted. The free connector is terminated to a cable consisting of 14 to 110 conductors. 1.1.1 Minimum and maximum number of contacts The fixed and free connectors have a range of 14 to

22、110 contacts. The shape of the shell prevents mismating. Examples of contact arrangements are shown in figure 2. 1.2 Rating and characteristics Working voltage: 250 V a.c. Current rating: 0,5 A (0,005 mm), 1 A (0,09 mm) Insulation resistance: 500 M minimum (initial) Climatic category: PL1: 55/085/21

23、 PL2:55/085/0 Printed board thickness: 0,8 mm 1,0 mm 1,2 mm 1,6 mm 2,4 mm Contact spacing: Mating side: 1,27 mm pitch (double rows) Printed board side: 2,54 mm pitch 1,905 mm (four rows) Page3 4002:001367016NEPage5 EN610763100:2000Licensed Copy: Wang Bin, ISO/Exchange China Standards Information Cen

24、tre, 28 December 2004, Uncontrolled Copy, (c) BSI-67016-3001 9991:CEI 31 1.3 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this International Standard. For dated references, subsequent amendments to, or revis

25、ions of, any of these publications do not apply. However, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normat

26、ive document referred to applies. Members of IEC and ISO maintain registers of currently valid International Standards. IEC 60050(581):1978, International Electrotechnical Vocabulary (IEV) Chapter 581: Electro- mechanical components for electronic equipment IEC 60068-1:1988, Environmental testing Pa

27、rt 1: General and guidance Amendment 1 (1992) IEC 60352-4:1994, Solderless connections Part 4: Solderless non-accessible insulation displacement connections General requirements, test methods and practical guidance IEC 60410:1973, Sampling plans and procedures for inspection by attributes IEC 60512-

28、1:1994, Electromechanical components for electronic equipment Basic testing procedures and measuring methods Part 1: General IEC 60512-2:1985, Electromechanical components for electronic equipment Basic testing procedures and measuring methods Part 2: General examination, electrical continuity and c

29、ontact resistance tests, insulation tests and voltage stress tests Amendment 1 (1994) IEC 60512-3:1976, Electromechanical components for electronic equipment Basic testing procedures and measuring methods Part 3: Current-carrying capacity tests IEC 60512-4:1976, Electromechanical components for elec

30、tronic equipment Basic testing procedures and measuring methods Part 4: Dynamic stress tests IEC 60512-5:1992, Electromechanical components for electronic equipment Basic testing procedures and measuring methods Part 5: Impact tests (free components), static load tests (fixed components), endurance

31、tests and overload tests IEC 60512-6:1984, Electromechanical components for electronic equipment Basic testing procedures and measuring methods Part 6: Climatic tests and soldering tests IEC 60512-7:1993, Electromechanical components for electronic equipment Basic testing procedures and measuring me

32、thods Part 7: Mechanical operating tests and sealing tests IEC 60512-8:1993, Electromechanical components for electronic equipment Basic testing procedures and measuring methods Part 8: Connector tests (mechanical) and mechanical tests on contacts and terminations Pa4eg E4002:001367016NPage6 EN61076

33、3100:2000Licensed Copy: Wang Bin, ISO/Exchange China Standards Information Centre, 28 December 2004, Uncontrolled Copy, (c) BSI-67016-3001 9991:CEI 51 IEC 60512-9:1992, Electromechanical components for electronic equipment Basic testing procedures and measuring methods Part 9: Miscellaneous tests IE

34、C 60512-11-1:1995, Electromechanical components for electronic equipment Basic testing procedures and measuring methods Part 11: Climatic tests Section 1: Test 11a Climatic sequence IEC 61076-1:1995, Connectors with assessed quality, for use in d.c., low frequency analogue applications and in digita

35、l high speed data applications Part 1: Generic specification IEC 61076-3, Connectors with assessed quality, for use in d.c., low frequency analogue and digital high speed data applications Part 3: Rectangular connectors 1)1.4 Marking The marking of the connector and the package shall be in accordanc

36、e with the requirements of the sectional specification IEC 61076-3. 1.5 IEC type designation Each connector and its associated package shall be marked in accordance with the requirements specified in 2.5 of IEC 61076-1. _ 1)To be published. Pa5eg E4002:001367016NPage7 EN610763100:2000Licensed Copy:

37、Wang Bin, ISO/Exchange China Standards Information Centre, 28 December 2004, Uncontrolled Copy, (c) BSI-67016-3001 9991:CEI 71 L L L NNN IEC 61076-3-100 Reference to standard L L L N G Assessment level Assessment level 1 1 Performance level Performance level 1 2 Board retention A B C D Screw Retenti

38、on leg Clip Other Board thickness A B C D E 0,8 mm 1,0 mm 1,2 mm 1,6 mm 2,4 mm Type of termination S I Insulation displacement Solder Style of connector Fixed connectors Shielded right-angle with locking latch A Shielded right-angle with screw lock B Shielded vertical with screw latch C D Shielded w

39、ith locking latch, cable type E Free connectors Shielded with locking latch K Shielded with screw lock L Number of contacts 014, 020, 026, 036, 040, 050, 068, 080, 096, 100, 110 Type of contact Ribbon R “L“ stands for letter “N“ stands for number Performance level 2 Shielded vertical with screw lock

40、Example IEC 61076-3 -100 A020RSDB-1G: Fixed connector, shielded right angle with locking latch, 20 contacts, ribbon contact, solder termination, board thickness 1,6 mm, board retention is retention leg, meeting performance level 1, assessment level G. Pa6eg E4002:001367016NPage8 EN610763100:2000Lice

41、nsed Copy: Wang Bin, ISO/Exchange China Standards Information Centre, 28 December 2004, Uncontrolled Copy, (c) BSI-67016-3001 9991:CEI 91 1.6 Ordering information For ordering connectors according to this detail specification, the type designation described in 1.5 shall be used. 2 Technical data 2.1

42、 General This International Standard applies to a range of shielded two-part connectors with trapezoidal- shaped shells and non-removable ribbon contacts on 1,27 mm double rows. The fixed connectors are provided with a post either for dip solder (type A, B, C, D) or non- accessible insulation displa

43、cement terminations (type E). The free connectors are provided with non-accessible insulation displacement terminations. Insulation displacement terminations are applicable to insulation displacement connection made with ribbon cable (type E) or single wires (type K, L) having: solid conductors: 0,2

44、5 mm diameter (0,05 mm 2 ) (AWG 30); stranded conductors: 0,09 mm 2 (AWG 28) 7 strands. 2.2 Survey of styles and variants Table 1 Style survey Type of connector Style of connectors Reference letter of the style Shielded right-angle with locking latch A Shielded right-angle with screw lock B Fixed Sh

45、ielded vertical with locking latch C Shielded vertical with screw lock D Shielded with locking latch, cable type E Free Shielded with locking latch K Shielded with screw lock L 2.3 Information on application See clause 3. 3 Dimensional information 3.1 General Original dimensions are in millimetres.

46、Drawings are shown in third-angle projection. The shape of the connectors may deviate from those given in the following figures as long as the specified dimensions are not influenced. Pa7eg E4002:001367016NPage9 EN610763100:2000Licensed Copy: Wang Bin, ISO/Exchange China Standards Information Centre

47、, 28 December 2004, Uncontrolled Copy, (c) BSI-67016-3001 9991:CEI 12 In cases where the tolerance is unspecified, 0,3 mm is the tolerance required for millimetre dimensions stated to one decimal place, 0,13 mm is the tolerance required for millimetre dimensions stated to two decimal places and 0,10

48、 mm is the tolerance required for millimetre dimensions stated to three decimal places. Dimensions in parentheses are only for reference on design, but not for inspection. 3.2 Isometric view and common features (with locking devices) Figure 1a Shielded right-angle fixed connector with latch locking

49、device (style A) and free connector with latch locking device (style K) and cover case Figure 1b Shielded vertical fixed connector with latch locking (style C) Figure 1 Connectors with latch locking devices 3.3 Mating information 3.3.1 Contact arrangements Contact arrangements, mating face view of fi