BS EN 60384-19-2015 Fixed capacitors for use in electronic equipment Sectional specification Fixed metallized polyethylene-terephthalate film dielectric surface mount d c capacitor.pdf

《BS EN 60384-19-2015 Fixed capacitors for use in electronic equipment Sectional specification Fixed metallized polyethylene-terephthalate film dielectric surface mount d c capacitor.pdf》由会员分享，可在线阅读，更多相关《BS EN 60384-19-2015 Fixed capacitors for use in electronic equipment Sectional specification Fixed metallized polyethylene-terephthalate film dielectric surface mount d c capacitor.pdf（36页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationFixed capacitors for use in electronic equipmentPart 19: Sectional specification: Fixed metallized polyethylene-terephthalate film dielectric surface mount d.c. capacitorsBS EN 60384-19:2015National forewordThis British Standard is the UK implementation of EN 60384-19:2015.

2、It isidentical to IEC 60384-19:2015. It supersedes BS EN 60384-19:2006 which iswithdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee EPL/40X, Capacitors and resistors for electronic equipment.A list of organizations represented on this committee can be obtained onrequ

3、est to its secretary.This publication does not purport to include all the necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 83166 9ICS 31.060.30Compliance with a British S

4、tandard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 December 2015.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 60384-19:2015EUROPEAN STANDARD NORME EU

5、ROPENNE EUROPISCHE NORM EN 60384-19 December 2015 ICS 31.060.30 Supersedes EN 60384-19:2006 English Version Fixed capacitors for use in electronic equipment - Part 19: Sectional specification: Fixed metallized polyethylene-terephthalate film dielectric surface mount d.c. capacitors (IEC 60384-19:201

6、5) Condensateurs fixes utiliss dans les quipements lectroniques - Partie 19: Spcification intermdiaire: Condensateurs fixes pour montage en surface pour courant continu dilectrique en film de polythylne trphtalate mtallis (IEC 60384-19:2015) Festkondensatoren zur Verwendung in Gerten der Elektronik

7、- Teil 19: Rahmenspezifikation - Oberflchenmontierbare Gleichspannungs-Kondensatoren mit metallisierter Polyethylen-Terephtalat-Folie als Dielektrikum (IEC 60384-19:2015) This European Standard was approved by CENELEC on 2015-05-20. CENELEC members are bound to comply with the CEN/CENELEC Internal R

8、egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENEL

9、EC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official

10、versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta

11、, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Ma

12、nagement Centre: Avenue Marnix 17, B-1000 Brussels 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN 60384-19:2015 E BS EN 60384-19:2015EN 60384-19:2015 (E) 2 European foreword The text of document 40/2342/FDIS, future edition 3

13、of IEC 60384-19, prepared by IEC/TC 40 “Capacitors and resistors for electronic equipment“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 60384-19:2015. The following dates are fixed: latest date by which the document has to be implemented at national level by publicati

14、on of an identical national standard or by endorsement (dop) 2016-06-04 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2018-05-20 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights

15、. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 60384-19:2015 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the follow

16、ing notes have to be added for the standards indicated: IEC 60068 series NOTE Harmonized in EN 60068 series. IEC 60384-19-1 NOTE Harmonized in EN 60384-19-1. BS EN 60384-19:2015EN 60384-19:2015 (E) 3 Annex ZA (normative) Normative references to international publications with their corresponding Eur

17、opean publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendment

18、s) applies. NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu. Publication Year Titl

19、e EN/HD Year IEC 60062 - Marking codes for resistors and capacitors EN 60062 - + corrigendum 2007 IEC 60063 - Preferred number series for resistors and capacitors EN 60063 - IEC 60068-1 2013 Environmental testing - Part 1: General and guidance EN 60068-1 2014 IEC 60384-1 2008 Fixed capacitors for us

20、e in electronic equipment - Part 1: Generic specification EN 60384-1 2009 IEC 61193-2 2007 Quality assessment systems - Part 2: Selection and use of sampling plans for inspection of electronic components and packages EN 61193-2 2007 ISO 3 - Preferred numbers; Series of preferred numbers - - BS EN 60

21、384-19:2015 2 IEC 60384-19:2015 IEC 2015 CONTENTS FOREWORD . 5 1 General . 7 1.1 Scope . 7 1.2 Object . 7 1.3 Normative references 7 1.4 Information to be given in a detail specification . 8 1.4.1 General . 8 1.4.2 Outline drawing and dimensions 8 1.4.3 Mounting . 8 1.4.4 Ratings and characteristics

22、 8 1.4.5 Marking . 9 1.5 Terms and definitions 9 1.6 Marking . 9 1.6.1 General . 9 1.6.2 Information for marking 9 1.6.3 Marking of capacitors 9 1.6.4 Marking on packaging 10 2 Preferred ratings and characteristics . 10 2.1 Preferred characteristics . 10 2.1.1 Preferred climatic categories . 10 2.2

23、Preferred values of ratings 10 2.2.1 Nominal capacitance (CN) 10 2.2.2 Tolerance on nominal capacitance . 10 2.2.3 Rated voltage (UR) . 10 2.2.4 Category voltage (UC) 11 2.2.5 Rated temperature . 11 3 Quality assessment procedures . 11 3.1 Primary stage of manufacture . 11 3.2 Structurally similar c

24、omponents 11 3.3 Certified test records of released lots 11 3.4 Qualification approval procedures . 11 3.4.1 General . 11 3.4.2 Qualification approval on the basis of the fixed sample size procedure 11 3.5 Quality conformance inspection 19 3.5.1 Formation of inspection lots . 19 3.5.2 Test schedule

25、20 3.5.3 Delayed delivery 20 3.5.4 Assessment levels . 20 4 Test and measurement procedures 21 4.1 Mounting . 21 4.2 Visual examination and check of dimensions 21 4.2.1 General . 21 4.2.2 Visual examination and check of dimensions . 21 4.2.3 Requirements 21 4.3 Electrical tests 21 4.3.1 Voltage proo

26、f . 21 BS EN 60384-19:2015IEC 60384-19:2015 IEC 2015 3 4.3.2 Capacitance 22 4.3.3 Tangent of loss angle (tan ) . 22 4.3.4 Insulation resistance 23 4.4 Shear test . 24 4.5 Substrate bending test 25 4.5.1 General . 25 4.5.2 Initial inspections . 25 4.5.3 Final inspections and requirements 25 4.6 Resis

27、tance to soldering heat . 25 4.6.1 General . 25 4.6.2 Initial inspections . 25 4.6.3 Test conditions 25 4.6.4 Recovery . 25 4.6.5 Final inspections and requirements 25 4.7 Solderability 25 4.7.1 General . 25 4.7.2 Test conditions 26 4.7.3 Final inspections and requirements 26 4.8 Rapid change of tem

28、perature 26 4.8.1 General . 26 4.8.2 Initial inspections . 26 4.8.3 Test conditions 26 4.8.4 Final inspections and requirements 26 4.9 Climatic sequence. 26 4.9.1 General . 26 4.9.2 Initial inspections . 26 4.9.3 Dry heat 26 4.9.4 Damp heat, cyclic, test Db, first cycle 27 4.9.5 Cold. 27 4.9.6 Damp

29、heat, cyclic, test Db, remaining cycles . 27 4.9.7 Recovery . 27 4.9.8 Final inspections and requirements 27 4.10 Damp heat, steady state . 27 4.10.1 General . 27 4.10.2 Initial inspections . 27 4.10.3 Test conditions 27 4.10.4 Recovery . 27 4.10.5 Final inspections and requirements 27 4.11 Enduranc

30、e 28 4.11.1 General . 28 4.11.2 Initial inspections . 28 4.11.3 Test conditions 28 4.11.4 Final inspections and requirements 28 4.12 Charge and discharge . 28 4.12.1 General . 28 4.12.2 Initial inspections . 28 4.12.3 Test conditions 28 4.12.4 Recovery . 29 4.12.5 Final inspections and requirements

31、29 BS EN 60384-19:2015 4 IEC 60384-19:2015 IEC 2015 4.13 Component solvent resistance (if applicable) 29 4.14 Solvent resistance of marking (if applicable) . 29 Bibliography 30 Table 1 Percentage limit of the rated voltage at a.c. voltage frequency 11 Table 2 Test and sampling plan for qualification

32、 approval Assessment level EZ . 13 Table 3 Test schedule for qualification approval . 14 Table 4 Lot-by-lot inspection 20 Table 5 Periodic inspection 21 Table 6 Test voltages . 22 Table 7 Applicable tan values 23 Table 8 Requirements regarding insulation resistance . 24 Table 9 Correction factor dep

33、endent on temperature 24 Table 10 Test conditions 28 BS EN 60384-19:2015IEC 60384-19:2015 IEC 2015 5 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT Part 19: Sectional specification: Fixed metallized polyethylene-terephthalate film dielectric surface moun

34、t d.c. capacitors FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning stan

35、dardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparat

36、ion is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with

37、 the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subje

38、cts since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical

39、content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent po

40、ssible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide confo

41、rmity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its direc

42、tors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising

43、 out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is dra

44、wn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60384-19 has been prepared by IEC technical committee 40: Capacitors and resistors

45、for electronic equipment. This third edition cancels and replaces the second edition published in 2006 and constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) Revised all parts of the document based on the IEC D

46、irectives Part 2:2011 (sixth edition) to the extent practicable, and harmonization between other similar kind of documents. b) Revised tables and Clause 4 so as to prevent duplications and contradictions. BS EN 60384-19:2015 6 IEC 60384-19:2015 IEC 2015 The text of this standard is based on the foll

47、owing documents: FDIS Report on voting 40/2342/FDIS 40/2373/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. The list of all par

48、ts of the IEC 60384 series, under the (new) general title Fixed capacitors for use in electronic equipment, can be found on the IEC web site. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webs

49、tore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. BS EN 60384-19:2015IEC 60384-19:2015 IEC 2015 7 FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT Part 19: Sectional specification: Fixed metallized polyethylene-terephthalate film dielectric surface mount d.c. capacitors 1 General 1.1 Scope This part of IEC 60384 is applicable to fixed surface mo