BS EN 60204-1-2006+A1-2009 Safety of machinery — nElectrical equipment of nmachines — nPart 1 General requirements《机械设备安全性 机械设备用电气设备的一般要求》.pdf

《BS EN 60204-1-2006+A1-2009 Safety of machinery — nElectrical equipment of nmachines — nPart 1 General requirements《机械设备安全性 机械设备用电气设备的一般要求》.pdf》由会员分享，可在线阅读，更多相关《BS EN 60204-1-2006+A1-2009 Safety of machinery — nElectrical equipment of nmachines — nPart 1 General requirements《机械设备安全性 机械设备用电气设备的一般要求》.pdf（130页珍藏版）》请在麦多课文档分享上搜索。

1、Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 02/09/2010 07:30, Uncontrolled Copy, (c) BSIg49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58P

2、art 1: General requirementsICS 29.02013.110 ; 31.020;Safety of machinery Electrical equipment of machines BRITISH STANDARDBS EN 60204-1:2006 +A1:2009IncorporatingcorrigendumFebruary 2010BS EN 60204-1:2006+A1:2009Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 02/09/2010 07:30, Uncontrolled Co

3、py, (c) BSIThis British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 June 2006 BSI 2010ISBN 978 0 580 70975 3A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to inclu

4、de all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments/corrigenda issued since publicationDate Comments 30 April 2009 Implementation of IEC amendment 1:2008 with CENE

5、LEC endorsement A1:200931 May 2010 Implementation of CENELEC corrigendum February 2010. Replacement of Annex ZZthe number of the amendment. For example, text altered by IEC amendment 1 is indicated by !“.The CENELEC common modifications have been implemented at the appropriate places in the text. Th

6、e start and finish of each common modification is indicated in the text by tags . The UK participation in its preparation was entrusted to Technical Committee MCE/3, Safeguarding of machinery.National forewordThis British Standard is the UK implementation of EN 60204-1:2006+A1:2009, incorporating co

7、rrigendum February 2010. It is derived from IEC 60204-1:2005, incorporating amendment 1:2008. It supersedes BS EN 60204-1:2006 which is withdrawn.The start and finish of text introduced or altered by amendment is indicated in the text by tags. Tags indicating changes to IEC text carry EUROPEAN STAND

8、ARD EN 60204-1NORME EUROPENNE EUROPISCHE NORM 200 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2006 CENELEC - All rights of e

9、xploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60204-1:2006 E ICS 29.020 Supersedes EN 60204-1:1997English version Safety of machinery Electrical equipment of machines Part 1: General requirements (IEC 60204-1:2005, modified) Scurit des machines Equipeme

10、nt lectrique des machines Partie 1: Rgles gnrales (CEI 60204-1:2005, modifie) Sicherheit von Maschinen Elektrische Ausrstung von Maschinen Teil 1: Allgemeine Anforderungen (IEC 60204-1:2005, modifiziert) This European Standard was approved by CENELEC on 2006-06-01. CENELEC members are bound to compl

11、y with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secr

12、etariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as

13、the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal,

14、Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. :2006+ A1 February 9Incorporating corrigendum February 2010Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 02/09/2010 07:30, Uncontrolled Copy, (c) BSIForeword The text of the International Standard IEC 60204-1:20

15、05, prepared by IEC TC 44, Safety of machinery Electrotechnical aspects, together with common modifications prepared by the Technical Committee CENELEC TC 44X, Safety of machinery Electrotechnical aspects, was approved by CENELEC as EN 60204-1 on 2006-06-01. This European Standard supersedes EN 6020

16、4-1:1997. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2007-06-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2009-06-01

17、NOTE The application of this standard can involve the selection of components and/or parts that are to be integrated with the electrical equipment of a machine in accordance with the instructions and/or specifications of the manufacturers of the components and/or parts. Also, in the context of legis

18、lative duties that are applicable to machinery manufacturers within the European Union it is important to recognise that the safety of electrical equipment can involve the use of equipment and services provided by other parties (see 3.54). To assist manufacturers in satisfying these duties it can be

19、 necessary for the supplier of the equipment to obtain information about its intended use. This can be facilitated by establishing an agreement between the user and supplier on basic conditions and additional user requirements to enable proper design, application and utilization of the electrical eq

20、uipment of the machine. An enquiry form that can be used for this purpose is provided in Annex B. Such an agreement is not intended to reduce the level of safety of the electrical equipment provided by this standard. _ 2 Endorsement notice The text of the International Standard IEC 60204-1:2005 was

21、approved by CENELEC as a European Standard with agreed common modifications. _ BS EN 60204-1:2006+A1:2009 EN 60204-1:2006+A1:2009 (E)Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 02/09/2010 07:30, Uncontrolled Copy, (c) BSIForeword to amendment A1 The text of document 44/575/CDV, future ame

22、ndment 1 to IEC 60204-1:2005, prepared by IEC TC 44, Safety of machinery - Electrotechnical aspects, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as amendment A1 to EN 60204-1:2006 on 2009-02-01. The following dates were fixed: latest date by which the amendment has to

23、be implemented at national level by publication of an identical national standard or by endorsement (dop) 2009-11-01 latest date by which the national standards conflicting with the amendment have to be withdrawn (dow) 2012-02-01 Annex ZA has been added by CENELEC. _ Endorsement notice The text of a

24、mendment 1:2008 to the International Standard IEC 60204-1:2005 was approved by CENELEC as an amendment to the European Standard without any modification. _ 3 BS EN 60204-1:2006+A1:2009 EN 60204-1:2006+A1:2009 (E)Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 02/09/2010 07:30, Uncontrolled Co

25、py, (c) BSI 4 CONTENTS INTRODUCTION 8 1 Scope 2 Normative references .11 3 Definitions1 4 General requirements.20 4.1 General considerations20 4.2 Selection of equipment 21 4.3 Electrical supply 22 4.4 Physical environment and operating conditions 23 4.5 Transportation and storage25 4.6 Provisions f

26、or handling 25 4.7 Installation 25 5 Incoming supply conductor terminations and devices for disconnecting and switching off.2 5.1 Incoming supply conductor terminations 25 5.2 Terminal for connection to the external protective earthing system.26 5.3 Supply disconnecting (isolating) device26 5.4 Devi

27、ces for switching off for prevention of unexpected start-up 29 5.5 Devices for disconnecting electrical equipment 29 5.6 Protection against unauthorized, inadvertent and/or mistaken connection.30 6 Protection against electric shock 30 6.1 General.30 6.2 Protection against direct contact30 6.3 Protec

28、tion against indirect contact .33 6.4 Protection by the use of PELV .34 7 Protection of equipment35 7.1 General.35 7.2 Overcurrent protection.35 7.3 Protection of motors against overheating .38 7.4 Abnormal temperature protection.39 7.5 Protection against supply interruption or voltage reduction and

29、 subsequent restoration.39 7.6 Motor overspeed protection .40 7.7 Earth fault/residual current protection 40 7.8 Phase sequence protection40 7.9 Protection against overvoltages due to lightning and to switching surges40 8 Equipotential bonding.40 8.1 General.40 8.2 Protective bonding circuit 43 8.3

30、Functional bonding 46 8.4 Measures to limit the effects of high leakage current4 10356BS EN 60204-1:2006+A1:2009 EN 60204-1:2006+A1:2009 (E)Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 02/09/2010 07:30, Uncontrolled Copy, (c) BSI 5 9 Control circuits and control functions 46 9.1 Control ci

31、rcuits 46 9.2 Control functions .47 9.3 Protective interlocks 52 9.4 Control functions in the event of failure53 10 Operator interface and machine-mounted control devices .57 10.1 General.57 10.2 Push-buttons.58 10.3 Indicator lights and displays.60 10.4 Illuminated push-buttons61 10.5 Rotary contro

32、l devices .61 10.6 Start devices .61 10.7 Emergency stop devices61 10.8 Emergency switching off devices .62 10.9 Enabling control device .63 11 Controlgear: location, mounting, and enclosures.63 11.1 General requirements63 11.2 Location and mounting 63 11.3 Degrees of protection 65 11.4 Enclosures,

33、doors and openings 65 11.5 Access to controlgear 66 12 Conductors and cables .67 12.1 General requirements67 12.2 Conductors67 12.3 Insulation 68 12.4 Current-carrying capacity in normal service .68 12.5 Conductor and cable voltage drop69 12.6 Flexible cables 70 12.7 Conductor wires, conductor bars

34、and slip-ring assemblies71 13 Wiring practices .73 13.1 Connections and routing73 13.2 Identification of conductors74 13.3 Wiring inside enclosures76 13.4 Wiring outside enclosures76 13.5 Ducts, connection boxes and other boxes 79 14 Electric motors and associated equipment 81 14.1 General requireme

35、nts81 14.2 Motor enclosures.82 14.3 Motor dimensions 82 14.4 Motor mounting and compartments 82 14.5 Criteria for motor selection 82 14.6 Protective devices for mechanical brakes 83 15 Accessories and lighting.83 15.1 Accessories.83 15.2 Local lighting of the machine and equipment83 BS EN 60204-1:20

36、06+A1:2009 EN 60204-1:2006+A1:2009 (E)Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 02/09/2010 07:30, Uncontrolled Copy, (c) BSI 6 16 Marking, warning signs and reference designations 84 16.1 General.84 16.2 Warning signs .85 16.3 Functional identification.85 16.4 Marking of equipment 85 16

37、.5 Reference designations .86 17 Technical documentation86 17.1 General.86 17.2 Information to be provided .86 17.3 Requirements applicable to all documentation .87 17.4 Installation documents.87 17.5 Overview diagrams and function diagrams .88 17.6 Circuit diagrams 88 17.7 Operating manual89 17.8 M

38、aintenance manual .89 17.9 Parts list89 18 Verification.89 18.1 General.89 18.2 Verification of conditions for protection by automatic disconnection of supply .90 18.3 Insulation resistance tests .93 18.4 Voltage tests .94 18.5 Protection against residual voltages.94 18.6 Functional tests.9 18.7 Ret

39、esting.94 Annex A (normative) Protection against indirect contact in TN-systems 95 Annex B (informative) Enquiry form for the electrical equipment of machines99 Annex C (informative) Examples of machines covered by this part of IEC 60204103 Annex D (informative) Current-carrying capacity and overcur

40、rent protection of conductors and cables in the electrical equipment of machines .105 Annex E (informative) Explanation of emergency operation functions .111 Annex F (informative) Guide for the use of this part of IEC 60204.112 Annex G (informative) Comparison of typical conductor cross-sectional ar

41、eas 114 Annex ZA (normative) Normative references to international publications with their corresponding European publications .116 Annex ZZ (informative) Coverage of Essential Requirements of EC Directives.120 Bibliography .121 Index123 Figure 1 Block diagram of a typical machine.9 Figure 2 Example

42、 of equipotential bonding for electrical equipment of a machine42 Figure 3 Method a) 5Figure 4 Method b) 5 Figure A.1 Typical arrangement for fault loop impedance measurement98 46 6 BS EN 60204-1:2006+A1:2009 EN 60204-1:2006+A1:2009 (E)Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 02/09/201

43、0 07:30, Uncontrolled Copy, (c) BSI 7 Figure D.1 Methods of conductor and cable installation independent of number of conductors/cables.106 Figure D.2 Parameters of conductors and protective devices108 Table 1 Minimum cross-sectional area of the external protective copper conductor.26 Table 2 Colour

44、-coding for push-button actuators and their meanings 59 Table 3 Symbols for push-buttons 59 Table 4 Colours for indicator lights and their meanings with respect to the condition of the machine60 Table 5 Minimum cross-sectional areas of copper conductors 67 Table 6 Examples of current-carrying capaci

45、ty (Iz) of PVC insulated copper conductors or cables under steady-state conditions in an ambient air temperature of +40 C for different methods of installation69 Table 7 Derating factors for cables wound on drums 71 Table 8 Minimum permitted bending radii for the forced guiding of flexible cables.78

46、 Table 9 Application of the test methods for TN-systems92 Table 10 Examples of maximum cable length from each protective device to its load 93 Table A.1 Maximum disconnecting times for TN systems95 Table D.1 Correction factors 105 Table D.2 Derating factors from Izfor grouping107 Table D.3 Derating

47、factors from Izfor multicore cables up to 10 mm2.107 Table D.4 Classification of conductors .108 Table D.5 Maximum allowable conductor temperatures under normal and short-circuit conditions.109 Table F.1 Application options.113 Table G.1 Comparison of conductor sizes 11 4BS EN 60204-1:2006+A1:2009 E

48、N 60204-1:2006+A1:2009 (E)Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 02/09/2010 07:30, Uncontrolled Copy, (c) BSI INTRODUCTION This part of IEC 60204 provides requirements and recommendations relating to the electrical equipment of machines so as to promote: safety of persons and propert

49、y; consistency of control response; ease of maintenance. More guidance on the use of this part of IEC 60204 is given in Annex F. Figure 1 has been provided as an aid to the understanding of the inter-relationship of the various elements of a machine and its associated equipment. Figure 1 is a block diagram of a typical machine and associated equipment showing the various elements of the electrical equipment addressed in this par