BS EN 16146-2012 Sanitary tapware Extractable shower hoses for sanitary tapware for supply systems type 1 and type 2 General technical specification《卫生开关龙头 1型和2型供水系统用卫生开关龙头的可抽出淋浴软管.pdf

《BS EN 16146-2012 Sanitary tapware Extractable shower hoses for sanitary tapware for supply systems type 1 and type 2 General technical specification《卫生开关龙头 1型和2型供水系统用卫生开关龙头的可抽出淋浴软管.pdf》由会员分享，可在线阅读，更多相关《BS EN 16146-2012 Sanitary tapware Extractable shower hoses for sanitary tapware for supply systems type 1 and type 2 General technical specification《卫生开关龙头 1型和2型供水系统用卫生开关龙头的可抽出淋浴软管.pdf（28页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 16146:2012Sanitary tapware Extractable shower hoses forsanitary tapware for supplysystems type 1 and type 2 General technical specificationCopyright European Committee for

2、Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 16146:2012 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 16146:2012.The UK participation in its preparation was entru

3、sted to TechnicalCommittee B/504/-/8, Sanitary tapware.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The Britis

4、h Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 71793 2ICS 91.140.70Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 January 2

5、013.Amendments issued since publicationDate Text affectedCopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 16146:2012EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1614

6、6 December 2012 ICS 91.140.70 English Version Sanitary tapware - Extractable shower hoses for sanitary tapware for supply systems type 1 and type 2 - General technical specification Robinetterie sanitaire - Flexibles de douchettes extractibles pour robinetterie sanitaire pour les systmes dalimentati

7、on en eau de types 1 et 2 - Spcifications techniques gnrales Sanitrarmaturen - Ausziehbare Brauseschluche fr Sanitrarmaturen fr Wasserversorgungssysteme vom Typ 1 und Typ 2 - Allgemeine technische Spezifikation This European Standard was approved by CEN on 10 November 2012. CEN members are bound to

8、comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CEN

9、ELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has th

10、e same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxemb

11、ourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN A

12、ll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16146:2012: ECopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN

13、 16146:2012EN 16146:2012 (E) 2 Contents Page Foreword . 3 Introduction 4 1 Scope 5 2 Normative references . 8 3 Terms and definitions 8 4 Designation 8 5 Marking . 8 6 Materials . 9 6.1 Chemical and hygienic requirements 9 6.2 Exposed surface condition and quality of coating . 9 7 Dimensional charac

14、teristics 9 7.1 General . 9 7.2 Connecting dimensions . 9 7.3 Special cases . 10 8 Hydraulic characteristics . 11 8.1 General . 11 8.2 Flow rate . 11 9 Mechanical and leaktightness characteristics 12 9.1 General . 12 9.2 Tensile strength . 12 9.3 Flexing durability test 13 9.4 Durability test . 15 9

15、.5 Pressure resistance at elevated temperature . 16 9.6 Thermal shock test . 18 10 Rotary connection 19 10.1 General . 19 10.2 Test Method 19 Annex A (informative) Pressure take-off tee 21 Bibliography 24 Copyright European Committee for Standardization Provided by IHS under license with CENNot for

16、ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 16146:2012EN 16146:2012 (E) 3 Foreword This document (EN 16146:2012) has been prepared by Technical Committee CEN/TC 164 “Water supply”, the secretariat of which is held by AFNOR. This European Standard shall be given t

17、he status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2013, and conflicting national standards shall be withdrawn at the latest by June 2013. Attention is drawn to the possibility that some of the elements of this document may be the su

18、bject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium,

19、Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland

20、, Turkey and the United Kingdom. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 16146:2012EN 16146:2012 (E) 4 Introduction In respect of potential adverse effects on the q

21、uality of water intended for human consumption caused by the product covered by this standard, this standard provides no information as to whether the product may be used without restriction in any of the Member States of the EU or EFTA. It should be noted that, while awaiting the adoption of verifi

22、able European criteria, existing national regulations concerning the use and/or the characteristics of this product remain in force. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,

23、-,-BS EN 16146:2012EN 16146:2012 (E) 5 1 Scope This European Standard applies to hoses for extractable outlets of any material intended for equipping sanitary tapware for sinks and basins. Such hoses will only be connected downstream of the obturator of the tapware. The tapware will comply with EN 2

24、00, EN 817, EN 1111, EN 1286 or EN 1287 (see 1, 2, 3, 5 and 6). Hoses intended to connect sanitary tapware to the water supplies are not covered by this standard. This European Standard specifies: the dimensional, mechanical and hydraulic characteristics with which the hose for extractable outlets s

25、hall comply; the procedures for testing these characteristics. Details of pressures and temperatures are given in Table 1. Table 1 Conditions of use/Classifications Water Supply system Operating range of hoses for extractable outlets Flow rates (Q) Limits Recommended Type 1 see Figure 1Dynamic Press

26、ure 0,05 MPa P 0,5 MPa (0,5 bar P 5 bar) Dynamic Pressure 0,1 MPa to 0,3 MPa (1,0 bar to 3,0 bar) Class 1: Min. 0,25 l/s (15 l/min) Class 2: Min. 0,15 l/s (9 l/min) Type 2 see Figure 2Dynamic Pressure 0,01 MPa to 0,2 MPa (0,1 bar to 2,0 bar Dynamic Pressure 0,02 MPa to 0,10 MPa (0,2 bar to 1,0 bar)

27、Class E: 0,06 l/s Q 0,18 l/s (3,6 l/min Q 10,8 l/min.) Class H: 0,18 l/s Q (10,8 l/min Q) Temperature T 70C T 60C Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 16146:2012

28、EN 16146:2012 (E) 6 Key 1 cold water 2 hot Water 3 mains supply pipe (Supply pressures up to 1,0 MPa (10 bar) 4 water heater Figure 1 Type 1 Supply system - with a pressure range of 0,05 MPa to 1,0 MPa (0,5 bar to 10 bar) Copyright European Committee for Standardization Provided by IHS under license

29、 with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 16146:2012EN 16146:2012 (E) 7 Key 1 cold water storage cistern (cover omitted for clarity) 2 warning pipe 3 vent pipe 4 hot water cylinder 5 alternative cistern fed cold supply to sanitary appliances 6

30、to boiler 7 mains supply pipe (Supply pressures up to 1,0 MPa (10 bar) Figure 2 Type 2-Supply system - with a pressure range of 0,01 MPa to 1,0 MPa, (0,1 bar to 10 bar): A vented domestic hot water and cold water supply system incorporating gravity hot water, mains cold water and alternative gravity

31、 cold water supply to sanitary appliances Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 16146:2012EN 16146:2012 (E) 8 2 Normative references The following documents, in w

32、hole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 248, Sanitary tapware General spe

33、cification for electrodeposited coatings of Ni-Cr EN ISO 228-1, Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation (ISO 228-1) 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 ho

34、se for extractable outlets flexible supply pipe which connects sanitary tapware to an extractable outlet 4 Designation Hoses for extractable outlets complying with this standard, are designated by: type; connecting thread dimensions e.g. G 1/2 G 1/2 or G 1/2 G 3/4; length; material of the external s

35、heath (plastic, metal); type of nuts and if conical the dimension C; reference to this standard: EN 16146; flow rate Class (see Table 1). EXAMPLE Hose for extractable outlet type, G 1/2, cone 26 G 3/4, length 1,5m, metal sheath, EN 16146, Class H. 5 Marking Extractable hoses complying with this stan

36、dard shall be marked permanently and legibly with the manufacturers mark or the suppliers mark. The flow rate class shall appear on the product but it need not be permanent. Hoses for extractable outlets with special dimensions (see 7.3) delivered together with the tapware need not be marked individ

37、ually. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 16146:2012EN 16146:2012 (E) 9 6 Materials 6.1 Chemical and hygienic requirements All materials coming into contact wi

38、th water intended for human consumption shall present no risk to health. They shall not cause any change of the drinking water in terms of quality, appearance, smell or taste. 6.2 Exposed surface condition and quality of coating Visible chromium plated surfaces and Ni-Cr coatings shall comply with t

39、he requirements of EN 248. 7 Dimensional characteristics 7.1 General General comment on design: the design and construction of components without defined dimensions permits various design solutions to be adopted by the manufacturer; permitted deviations from the defined dimensions are given in 7.3.

40、7.2 Connecting dimensions The connecting dimensions of hoses for extractable outlets are specified in Table 2 and Figures 3 to 5. Table 2 Connecting dimensions Dimensions Values Comments A G 1/2, G 3/8 or 15 x 1 mm or other EN ISO dimensions Connecting thread (tap side) B G 1/2 Connecting thread (ex

41、tractable outlet side) EN ISO 228-1 C 23 5010,+mm or 26 5010,+mm Major diameter of conical nut (if provided) G 8,5 0/-1 mm Functional dimension on seal depth I 1,5 500, +mm Thread counter bore K 30 mm Total length of conical nut 3 0/-1 mm Cone angle (if provided) L 500 mm Total length of hose Copyri

42、ght European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 16146:2012EN 16146:2012 (E) 10 a) Conical nut b) Nut (shape unspecified) Figure 3 Terminal nuts Figure 4 Female or male end (shape

43、 unspecified) Figure 5 Hose length 7.3 Special cases Hoses for extractable outlets intended for special applications e.g. when interchangeability is not a requirement, can incorporate the following dimensional deviations: connection to the tapware is guaranteed; threaded connections are in complianc

44、e with ISO standards; all other requirements of this standard are satisfied; the manufacturers literature, including the installation instructions supplied with the hoses for extractable outlets, indicates clearly that the hoses for extractable outlets are special cases. Copyright European Committee

45、 for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 16146:2012EN 16146:2012 (E) 11 8 Hydraulic characteristics 8.1 General The test described is a type test (laboratory test) and not a quality control tes

46、t carried out during manufacture. 8.2 Flow rate 8.2.1 Test method This clause describes a method for testing the flow rate of hoses. 8.2.2 Principle The principle consists of a method for measuring the flow rate through the hoses for extractable outlets using cold water (T 30 C) in order to determin

47、e the flow rate class of the hose (see Table 1). The flow rate of hoses for extractable outlets with special connection (see 7.3) delivered together with the tapware is measured in combination with the complete sanitary tapware. 8.2.3 Apparatus The test apparatus is shown in Figure 6. 8.2.4 Procedur

48、e Connect the G size nut of the hose for extractable outlets to the pressure take-off tee, supporting the hose in a horizontal position; apply the required dynamic pressure using the horizontal axis of the hose as a datum; record the flow rate “Q“ (Table 1) after stabilisation. 8.2.5 Requirements Hoses for extractable outlets shall be classified according to the flow rate value “Q“ at the required pressure as