BS EN 13599-2014 Copper and copper alloys Copper plate sheet and strip for electrical purposes《铜和铜合金 电气用途的铜板 铜片和铜条》.pdf

《BS EN 13599-2014 Copper and copper alloys Copper plate sheet and strip for electrical purposes《铜和铜合金 电气用途的铜板 铜片和铜条》.pdf》由会员分享，可在线阅读，更多相关《BS EN 13599-2014 Copper and copper alloys Copper plate sheet and strip for electrical purposes《铜和铜合金 电气用途的铜板 铜片和铜条》.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS EN 13599:2014Copper and copper alloys Copper plate, sheet and stripfor electrical purposesBS EN 13599:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 13599:2014. Itsupersedes BS EN 13599:2002 which is withdrawn.The UK participati

2、on in its preparation was entrusted to TechnicalCommittee NFE/34/1, Wrought and unwrought copper and copperalloys.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. U

3、sers are responsible for its correctapplication. The British Standards Institution 2014. Published by BSI StandardsLimited 2014ISBN 978 0 580 82036 6ICS 77.150.30Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of

4、 theStandards Policy and Strategy Committee on 28 February 2014.Amendments issued since publicationDate Text affectedBS EN 13599:2014EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13599 January 2014 ICS 77.150.30 Supersedes EN 13599:2002English Version Copper and copper alloys - Copper plate,

5、sheet and strip for electrical purposes Cuivre et alliages de cuivre - Plaques, tles et bandes en cuivre pour usages lectriques Kupfer und Kupferlegierungen - Platten, Bleche und Bnder aus Kupfer fr die Anwendung in der Elektrotechnik This European Standard was approved by CEN on 3 November 2013. CE

6、N members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on app

7、lication to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC M

8、anagement Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, La

9、tvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Ma

10、rnix 17, B-1000 Brussels 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13599:2014 EBS EN 13599:2014EN 13599:2014 (E) 2 Contents Page Foreword 3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Designations 5 4

11、.1 Material .5 4.2 Material condition 5 4.3 Product .5 5 Ordering information .6 6 Requirements .8 6.1 Composition .8 6.2 Mechanical properties .8 6.3 Bending characteristics 8 6.4 Electrical properties 8 6.5 Freedom from hydrogen embrittlement 8 6.6 Dimensions and tolerances 9 6.7 Edgewise curvatur

12、e c 9 6.8 Surface condition.9 7 Sampling .9 7.1 General 9 7.2 Analysis 9 7.3 Mechanical and electrical tests . 10 8 Test methods . 10 8.1 Analysis . 10 8.2 Tensile test 10 8.3 Hardness test 10 8.4 Bend test 10 8.5 Electrical resistivity test . 11 8.6 Hydrogen embrittlement test . 11 8.7 Retests . 12

13、 8.8 Rounding of results 12 9 Declaration of conformity and inspection documentation . 12 9.1 Declaration of conformity 12 9.2 Inspection documentation . 12 10 Marking, packaging, labelling 12 Annex A (informative) Characteristics of coppers for electrical purposes 19 A.1 General grouping of copper

14、types 19 A.2 General characteristics 19 A.3 Particular characteristics . 19 Bibliography . 21 BS EN 13599:2014EN 13599:2014 (E) 3 Foreword This document (EN 13599:2014) has been prepared by Technical Committee CEN/TC 133 “Copper and copper alloys”, the secretariat of which is held by DIN. This Europ

15、ean Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2014, and conflicting national standards shall be withdrawn at the latest by July 2014. Attention is drawn to the possibility that some of the elements o

16、f this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13599:2002. Within its programme of work, Technical Committee CEN/TC 133 requested CEN/TC 133/WG 2 “Rolled flat products” t

17、o revise the following standard: EN 13599:2002, Copper and copper alloys Copper plate, sheet and strip for electrical purposes The products specified in this European Standard are those which are especially suitable for electrical purposes, i.e. with specified electrical properties. Copper plate, sh

18、eet and strip for general purposes are specified in EN 1652. This is one of a series of European Standards for copper products for electrical purposes. Other copper products are specified as follows: EN 13600, Copper and copper alloys Seamless copper tubes for electrical purposes EN 13601, Copper an

19、d copper alloys Copper rod, bar and wire for general electrical purposes EN 13602, Copper and copper alloys Drawn, round copper wire for the manufacture of electrical conductors EN 13604, Copper and copper alloys Products of high conductivity copper for electronic tubes, semiconductor devices and va

20、cuum applications EN 13605, Copper and copper alloys Copper profiles and profiled wire for electrical purposes In comparison with EN 13599:2002, the following significant changes were made: a) Table 2, Cu-FRHC, other elements content has been modified and a new footnote “d” has been added; b) the no

21、rmative references have been updated. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugos

22、lav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 13599:2014EN 13599:2014 (E) 4 1 Scope This

23、European Standard specifies the composition, property requirements including electrical properties, and tolerances on dimensions and form for copper plate, sheet and strip for electrical purposes with thicknesses from 0,05 mm up to and including 25 mm and widths from 10 mm up to and including 1 250

24、mm. The sampling procedures and the methods of test for verification of conformity to the requirements of this European Standard are also specified. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its applicat

25、ion. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1655, Copper and copper alloys - Declarations of conformity EN 1976, Copper and copper alloys - Cast unwrought copper products EN 10

26、204, Metallic products - Types of inspection documents EN ISO 2626, Copper - Hydrogen embrittlement test (ISO 2626) EN ISO 6507-1, Metallic materials - Vickers hardness test - Part 1: Test method (ISO 6507-1) EN ISO 6892-1, Metallic materials - Tensile testing - Part 1: Method of test at room temper

27、ature (ISO 6892-1) EN ISO 7438, Metallic materials - Bend test (ISO 7438) ISO 1811-2, Copper and copper alloys Selection and preparation of samples for chemical analysis Part 2: Sampling of wrought products and castings 3 Terms and definitions For the purposes of this document, the following terms a

28、nd definitions apply. 3.1 plate flat rolled product of rectangular cross-section with uniform thickness greater than 10 mm 3.2 sheet flat rolled product of rectangular cross-section with uniform thickness from 0,2 mm up to and including 10 mm, supplied in straight lengths, usually with sheared or sa

29、wn edges Note 1 to entry: The thickness does not exceed one tenth of the width. 3.3 strip flat rolled product of rectangular cross-section with uniform thickness from 0,05 mm up to and including 5,0 mm manufactured in coil and supplied in as sheared coils, traverse wound coils or cut to length, usua

30、lly with slit edges Note 1 to entry: The thickness does not exceed one tenth of the width. BS EN 13599:2014EN 13599:2014 (E) 5 4 Designations 4.1 Material 4.1.1 General The material is designated either by symbol or by number (see Table 1). 4.1.2 Symbol The material symbol designation is based on th

31、e designation system given in ISO 1190-1. NOTE Although material symbol designations used in this standard might be the same as those in other standards using the designation system in ISO 1190-1, the detailed composition requirements are not necessarily the same. 4.1.3 Number The material number de

32、signation is in accordance with the system given in EN 1412. 4.2 Material condition For the purposes of this standard, the following designations, which are in accordance with the system given in EN 1173, apply for the material condition: M Material condition for the product as manufactured without

33、specified mechanical properties; H Material condition designated by the minimum value of hardness requirement for the product with mandatory hardness requirements; R Material condition designated by the minimum value of tensile strength requirement for the product with mandatory tensile strength and

34、 elongation requirements. NOTE Some R. material conditions in this European Standard apply to products which also have mandatory 0,2 % proof strength requirements. Exact conversion between material conditions designated H. and R. is not possible. Material condition is designated by only one of the a

35、bove designations. 4.3 Product The product designation provides a standardised pattern of designation from which a rapid and unequivocal description of a product can be conveyed in communication. It provides mutual comprehension at the international level with regard to products which meet the requi

36、rements of the relevant European Standard. The product designation is no substitute for the full content of the standard. The product designation for products to this European Standard shall consist of: denomination (Plate, Sheet or Strip); number of this European Standard (EN 13599); material desig

37、nation, either symbol or number (see Table 1); material condition designation (see Table 2); BS EN 13599:2014EN 13599:2014 (E) 6 nominal dimensions; plate: thickness width length either “as manufactured” (ML) or “fixed” (FL) length; sheet: thickness width length either “as manufactured” (ML) or “fix

38、ed” (FL) length (see Example 1); strip (as sheared coils or as transverse wound coils on spools): thickness width (see Example 2); strip (cut to length): thickness width length either “as manufactured” (ML) or “fixed” (FL) length. The derivation of a product designation is shown in Example 1. EXAMPL

39、E 1 Sheet for electrical purposes conforming to this European Standard, in material designated either Cu-ETP or CW004A, in material condition H040, nominal thickness 6,0 mm, nominal width 600 mm, as manufactured length 2 000 mm, will be designated as follows: Sheet EN 13599 Cu-ETP H040 6,0 600 2 000

40、ML or Sheet EN 13599 CW004A H040 6,0 600 2 000ML Denomination Number of this European Standard Material designation Material condition designation Nominal dimension in millimetres EXAMPLE 2 Strip for electrical purposes conforming to this European Standard, in material designated either CuAg0,10 or

41、CW013A, in material condition R290, nominal thickness 2,0 mm, nominal width 1 000 mm, will be designated as follows: Strip EN 13599 CuAg0,10 R290 2,0 1 000 or Strip EN 13599 CW013A R290 2,0 1 000 5 Ordering information In order to facilitate the enquiry, order and confirmation of order procedures be

42、tween the purchaser and the supplier, the purchaser shall state on his enquiry and order the following information: a) quantity of product required: 1) plate: number of pieces or mass; 2) sheet: number of pieces or mass; 3) strip (as sheared coils or as transverse wound coils on spools): mass; 4) st

43、rip (cut to length): mass or number of pieces; BS EN 13599:2014EN 13599:2014 (E) 7 b) denomination (Plate, Sheet or Strip); c) number of this European Standard (EN 13599); d) material designation (see 4.1 and Table 1); e) material condition designation (see 4.2 and Table 2); f) nominal dimensions: 1

44、) plate, sheet, strip (cut to length): thickness for thicknesses from 0,05 mm up to and including 3,2 mm and with widths from 10 mm up to and including 200 mm, thickness tolerance either “normal” (N) or “special” (S) width length (either “as manufactured” or “fixed” length); 2) strip (as sheared coi

45、ls or as transverse wound coils on spools): thickness for thicknesses from 0,05 mm up to and including 3,2 mm and with widths from 10 mm up to and including 200 mm, thickness tolerance either “normal” (N) or “special” (S) width; g) size of sheared coils (strip) requirements: nominal inside diameter

46、in millimetres and maximum outside diameter in millimetres and either maximum mass in kilograms or approximate specific coil mass (mass per width) in kilograms per millimetre; h) size of traverse wound coils (strip): type or dimensions. It is recommended that the product designation, as described in

47、 4.3, is used for items b) to f). In addition, the purchaser shall also state on the enquiry and order any of the following, if required: i) maximum edgewise curvature values for strip over 3,2 mm up to and including 5,0 mm thickness and width over 30 mm (see Table 9); j) whether special surface con

48、ditions are required (see 6.8); k) whether a declaration of conformity is required (see 9.1); l) whether an inspection document is required, and if so, which type (see 9.2); m) whether there are any special requirements for marking, packaging or labelling (see Clause 10). EXAMPLE 1 Ordering details

49、for 100 sheets for electrical purposes conforming to EN 13599, in material designated either Cu-ETP or CW004A, in material condition H040, nominal thickness 6,0 mm, nominal width 600 mm, as manufactured length 2 000 mm: 100 pieces Sheet EN 13599 Cu-ETP H040 6,0 600 2 000ML or 100 pieces Sheet EN 13599 CW004A H040 6,0 600 2 000ML BS EN 13599:2014EN 13599:2014 (E) 8 EXAMPLE 2 Ordering details for 5 000 kg strip for electrical purposes conforming to EN 13599,