BS 6356-11-1997 Spraying equipment for crop protection Agricultural sprayers Determination of the volume of total residual《农作物保护喷雾设备 农业喷灌设备 残留物总量测定》.pdf

《BS 6356-11-1997 Spraying equipment for crop protection Agricultural sprayers Determination of the volume of total residual《农作物保护喷雾设备 农业喷灌设备 残留物总量测定》.pdf》由会员分享，可在线阅读，更多相关《BS 6356-11-1997 Spraying equipment for crop protection Agricultural sprayers Determination of the volume of total residual《农作物保护喷雾设备 农业喷灌设备 残留物总量测定》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS 6356-11: 1997 ISO 13440: 1996 Spraying equipment for crop protection Part 11: Agricultural sprayers Determination of the volume of total residual ICS 65.060.40BS6356-11:1997 This British Standard, having been prepared under the directionof the Engineering SectorBoard, was publish

2、ed underthe authority of the Standards Board and comesintoeffect on 15 September 1997 BSI 09-1999 ISBN 0 580 27806 9 National foreword This British Standard reproduces verbatim ISO13440:1996 and implements it as the UK national standard. The UK participation in its preparation was entrusted to Techn

3、ical Committee AGE/15, Equipment for crop protection, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related i

4、nternational and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be f

5、ound in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standa

6、rds are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theISOtitle page, pages ii to iv, pages1 to3 and a back cove

7、r. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No. Date CommentsBS6356-11:1997 BSI 09-1999 i Contents Page National foreword Inside fron

8、t cover Foreword iii Text of ISO 13440 1ii blankBS6356-11:1997 ii BSI 09-1999 Contents Page Foreword iii 1 Scope 1 2 Definitions 1 3 General 1 4 Procedure 1 5 Test report 1 Annex A (normative) Test report for the determination of the volume of totalredidual for agricultural sprayers, conforming to I

9、SO13440 2BS6356-11:1997 BSI 09-1999 iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member bo

10、dy interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrot

11、echnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least75% of the member bodies casting a vot

12、e. International Standard ISO 13440 was prepared by Technical Committee ISO/TC23, Tractors and machinery for agriculture and forestry, subcommittee SC6, Equipment for crop protection. Annex A forms an integral part of this International Standard. Descriptors: Agricultural equipment, crop protection,

13、 crops treatment equipment, agricultural sprayers, tests, determination, residue volume.iv blankBS6356-11:1997 BSI 09-1999 1 1 Scope This International Standard specifies the test method for the determination of the volume of total residual for mounted, trailed and self-propelled agricultural spraye

14、rs used for crop protection and fertilization. 2 Definitions For the purposes of this International Standard, the following definitions apply: 2.1 volume of total residual volume of the spray mixture remaining in the sprayer which cannot be delivered with the intended application rate and/or pressur

15、e, equal to the sum of the volume of residual tank and the dead volume 2.2 volume of residual in the tank; dilutible volume part of the total residual that remains in the tank or that can flow back to the tank during normal sprayer operation 2.3 dead volume; non dilutible volume part of the total re

16、sidual that cannot flow back to the tank during normal operation of the sprayer 2.4 horizontal position normal operating position of the sprayer on level ground 3 General 3.1 The test shall be carried out with the sprayer secured in a stationary and horizontal position. The pump shall be driven at n

17、ominal speed. The spray boom including liquid lines and nozzles shall be in working position. The boom shall be equipped with one size of nozzles recommended by the manufacturer. 3.2 The pressure shall be set such that the average liquid output of the nozzles is: a) 1 l/min for pneumatic sprayers; b

18、) 2 l/min for field crop sprayers and vineyard sprayers; c) 4 l/min for orchard sprayers; d) 6 l/min for hop plantation sprayers. NOTEThe output values given are for the normal case but other values can be used for particular cases. The liquid output of each nozzle shall be adjusted with an accuracy

19、 of 0,1l/min. The spray tank shall be half full or contain, at most,500l. The liquid used shall be water. 4 Procedure 4.1 On level ground Secure the sprayer in a horizontal position and in accordance with3.1. Set the pressure and the liquid nozzle output in accordance with3.2. Refill the amount of w

20、ater to be in accordance with3.2 and start the test. Let the sprayer discharge the water until the first pressure drop of25% for1s occurs. Then immediately stop the sprayer and measure the volume of the residual. Measure the volume of residual in the the tank and the dead volume, to an accuracy of0,

21、1% of the nominal tank volume. Repeat the measurement and record the average of the two measurements as the value of the volume of total residual. NOTEAlternatively, instead of measuring the volume of the residual, the sprayer can be weighed after the test and after the total discharge of the spraye

22、r. The residual volume can then be calculated. 4.2 On slopes 4.2.1 8,5 slope The sprayer shall be inclined to the left and to the right, to the front and to the rear at an angle of8,5 0,5 . In each of these positions, determine the volume of residual in the tank and the dead volume as stipulated in4

23、.1. 4.2.2 Maximal slope Optionally, an additional determination can be performed at an angle corresponding to the maximum slope recommended by the manufacturer. 5 Test report The test results shall be recorded in a test report which conforms toAnnex A.BS6356-11:1997 2 BSI 09-1999 Annex A (normative)

24、 Test report for the determination of the volume of total redidual for agricultural sprayers, conforming to ISO13440 A.1 Sprayer A.2 Volume of total residual (calculated values)BS6356-11:1997 BSI 09-1999 3 A.3 Volume of residual in the tank (measured values) A.4 Dead volume (measured values)BS 6356-

25、11: 1997 ISO 13440: 1996 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisi

26、ons BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambigu

27、ity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automat

28、ically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI imp

29、lementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic i

30、nformation services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standard

31、s. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the internationalstandardization bodies. Except as permitted under the

32、 Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementin

33、g the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.