ASTM F2868-2010(2015) Standard Specification for Condition 2 Bicycle Frames《第2类条件的自行车车架标准规格》.pdf
《ASTM F2868-2010(2015) Standard Specification for Condition 2 Bicycle Frames《第2类条件的自行车车架标准规格》.pdf》由会员分享,可在线阅读,更多相关《ASTM F2868-2010(2015) Standard Specification for Condition 2 Bicycle Frames《第2类条件的自行车车架标准规格》.pdf(2页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: F2868 10 (Reapproved 2015) An American National StandardStandard Specification forCondition 2 Bicycle Frames1This standard is issued under the fixed designation F2868; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, th
2、e year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.INTRODUCTIONThis specification standard defines a set of requirements for Condition 2 bicycle frames. Condition2 is a ve
3、hicle usage classification defined in Classification F2043 indicating the type of riding andsurface condition intended by design. Included are specifications for establishing loads and othercriteria to be used with the matching test method.1. Scope1.1 This standard establishes testing requirements f
4、or thestructural performance properties of Condition 2 bicycleframes.1.2 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.3 This standard is applicable to adult size suspension andnon-suspension bicycle frames.2. Referenced Doc
5、uments2.1 ASTM Standards:2F2043 Classification for Bicycle UsageF2711 Test Methods for Bicycle Frames3. Terminology3.1 Definitions:3.1.1 bicycle frame, nthe structural member that supportsthe seat with rear connection for the rear wheel, front connec-tion via the head tube for the fork and lower con
6、nection for thecrank/pedal assembly.4. Classification4.1 Condition 2 bicycle frame.5. Performance Requirements5.1 The bicycle frame shall be tested in accordance with themethods of Test Methods F2711, the Horizontal LoadingFatigue test, Vertical Loading Fatigue test, and the ImpactStrength test.5.1.
7、1 Horizontal Loading Fatigue TestThe frame shall betested and must complete a minimum 50 000 cycles with acyclic load of 800 N tensile and 600 N compressive.5.1.2 Vertical Loading Fatigue TestThe frame shall betested and must complete a minimum 50 000 cycles with acyclic load of 1200 N to 120 N load
8、 in the compressivedirection.5.1.3 Impact Strength TestThe frame shall be tested witha drop height of 180 mm, and the permanent set of the frameand fork shall be less than 40 mm.6. Rejection and Rehearing6.1 Frames that fail to meet the requirements of thisstandard shall be rejected.7. Certification
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMF286820102015STANDARDSPECIFICATIONFORCONDITION2BICYCLEFRAMES 条件 自行车 车架 标准 规格 PDF
链接地址:http://www.mydoc123.com/p-539625.html