ASTM F2727-2009 Standard Guide for Manufacturers for Labeling Headgear Products《标识头饰产品的制造商的标准指南》.pdf

《ASTM F2727-2009 Standard Guide for Manufacturers for Labeling Headgear Products《标识头饰产品的制造商的标准指南》.pdf》由会员分享，可在线阅读，更多相关《ASTM F2727-2009 Standard Guide for Manufacturers for Labeling Headgear Products《标识头饰产品的制造商的标准指南》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F 2727 09Standard Guide forManufacturers for Labeling Headgear Products1This standard is issued under the fixed designation F 2727; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in

2、 parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This guide sets forth labeling and instruction guidelinesfor manufacturers of headgear for non-motorized sports andrecreation.1.2 This guide app

3、lies only to protective headgear whosestandard specifications are under auspices of ASTM Commit-tee F08.1.3 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not c

4、onsidered standard.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to

5、use.2. Terminology2.1 Definitions:2.1.1 accompanying literature, nprinted material that ac-companies the product when it is sold or distributed.2.1.2 caution, nsignal word used to indicate a potentiallyhazardous situation that, if not avoided, may result in minor ormoderate injury.2.1.3 contact info

6、rmation, ninformation that allows theuser to contact the manufacturer of the product, such as name,telephone number, website address.2.1.4 danger, nsignal word used to alert the wearer to animminently hazardous situation that, if not avoided, will resultin serious injury or death and this signal wor

7、d is to be limitedto the most extreme situations.2.1.5 label, nprinted material that is physically attachedto the headgear in a durable fashion.2.1.6 label material, nsubstrate paper, fabric, or othermaterial from which the label is made.2.1.7 legible, adjcan be read by a person with 20/20corrected

8、vision from a distance of at least 18 in. (46 cm).2.1.8 manufacturer, nentity responsible for marketing theproduct.2.1.9 mounting location, nposition on or in the headgearin which information may be affixed.2.1.10 pictogram, ngraphic representation that depicts orillustrates an act or condition with

9、out the use of accompanyingwriting.2.1.11 signal word, nword that conveys a level of dangercommensurate with the risk of injury.2.1.12 warning, nsignal word used to indicate a poten-tially hazardous situation that, if not avoided, could result indeath or serious injury.2.2 Definitions of Terms Speci

10、fic to This Standard:2.2.1 date of manufacture, nuncoded four-digit year dur-ing which the headgear was manufactured.2.2.2 durable, adjlabel should be designed to be legibleas long as the manufacturers logo remains legible.2.2.3 expected life, nperiod of time during which theheadgear should be expec

11、ted to provide the advertised level ofprotection if not damaged by use or accident.3. Significance and Use3.1 This guide gives guidelines for labels and instructions tomanufacturers of non-motorized sports and recreation head-gear.3.2 The purpose of the labels and instructions is to help alertand re

12、mind headgear users of important issues related toheadgear and its use.3.3 LimitationThis guide applies only to protective head-gear whose standard specifications are under auspices ofASTM Committee F08.4. Helmet Labeling Requirements4.1 Required information shall be on one or more labels thatare af

13、fixed to the helmet in a durable fashion. The labels shallhave:4.1.1 Manufacturer IdentificationFull name.4.1.2 Manufacturer Contact InformationAt least one ofthe following shall be provided: (1) toll-free phone number, (2)mailing address, (3) website, or (4) e-mail address for customerservice.4.1.3

14、 SizeHat size, circumference in centimetres orinches, or equivalent.1This guide is under the jurisdiction of ASTM Committee F08 on SportsEquipment and Facilities and is the direct responsibility of Subcommittee F08.53 onHeadgear and Helmets.Current edition approved Jan. 1, 2009. Published March 2009

15、.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.4.1.4 Indicate what to do if damaged.4.1.4.1 End user should destroy and replace the helmet if itbecomes damaged beyond repair.4.1.4.2 In case of helmets that can be repaired or recert

16、ifiedthey should be repaired and recertified before use.4.1.5 An indication of materials and conditions that candamage the helmet.4.1.6 All information required to be placed on the helmet bythe ASTM International standard applicable to that helmet.4.1.7 Identification of all the standard(s) the manu

17、facturerclaims the headgear satisfies.4.1.8 Appropriate certification information.4.1.9 Model name or number or both.4.1.10 Date of manufacture.4.1.11 Instruction to read owners manual/manufacturersinstructions.5. Accompanying Literature Requirements5.1 Accompanying literature can be on product pack

18、aging,in instructions included with the product, and so forth. Theaccompanying literature shall have:5.1.1 Fit, use, and adjustment instructions such as:5.1.1.1 Pictogram showing correct positioning,5.1.1.2 Text describing fit and adjustment,5.1.1.3 Care instructions such as:(1) Cleaning instruction

19、s,(2) When to replace,(3) What materials can damage, and(4) Pre-use inspection.5.1.1.4 Warranty or where warranty can be accessed (web-site or equivalent).5.1.2 Manufacturer IdentificationFull name of manufac-turer including any other information needed to identify theresponsible entity.5.1.3 Manufa

20、cturer Contact InformationWebsite address,mailing address, and e-mail address for customer service.5.1.4 Any age or size limitations.5.1.5 Statement that modifying the product can reduce levelof protection.5.1.6 Statement to read and always comply with manufac-turers instructions.5.1.7 Statement to

21、always comply with all applicable laws.5.1.8 Statement to always comply with rules of applicablesports or activities.5.1.9 Identification of the standard(s) that the manufacturerclaims the headgear satisfies. Reference shall include name oforganization that created the standard and the full standard

22、 titleand number including any version information.5.1.10 Product packaging shall not contain words or graph-ics that would indicate that the headgear provides protection oris certified for activities that are not in compliance with theidentified standards required in 4.1.7 and 5.1.9.6. Keywords6.1

23、headgear; helmet; instructions; labelingBibliography(1) ASTM F 381, Standard Safety Specification for Components,Assembly, Use, and Labeling of Consumer Trampolines(2) ASTM F 1749, Standard Specification for Fitness Equipment andFitness Facility Safety Signage and Labels(3) ASTM F 2041, Standard Spe

24、cification for Paintball Marker Warn-ings(4) ANSI Z535.6, American National Standard for Product Safety(5) CPSC: 16 CFR Part 1203, Safety Standard for Bicycle Helmets(6) NOCSAE: ND-001, Standard Drop Test Method and EquipmentUsed in Evaluating the Performance Characteristics of ProtectiveHeadgear(7)

25、 FMVSS 218: Federal Motor Vehicle Safety Standard No. 218(Motorcycle Helmets)(8) ISO 3864-2, Graphical symbols - Safety colours and safety signs- Part 2: Design principles for product safety labelsASTM International takes no position respecting the validity of any patent rights asserted in connectio

26、n with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible

27、technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consid

28、eration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Bar

29、r Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).F2727092