ASTM D7834-2013 8125 Standard Test Method for Filling Material Shedding of Paint Brushes《油漆刷填料脱落的标准试验方法》.pdf

《ASTM D7834-2013 8125 Standard Test Method for Filling Material Shedding of Paint Brushes《油漆刷填料脱落的标准试验方法》.pdf》由会员分享，可在线阅读，更多相关《ASTM D7834-2013 8125 Standard Test Method for Filling Material Shedding of Paint Brushes《油漆刷填料脱落的标准试验方法》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D7834 13Standard Test Method forFilling Material Shedding of Paint Brushes1This standard is issued under the fixed designation D7834; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number

2、in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method describes the procedure for testing theshedding properties of both natural bristle and syntheticfilament paint brushes (refer

3、red as filling material).1.2 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 This standard does not purport to address all of thesafe

4、ty concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Summary of Test Method2.1 The amount of filling material removed in this

5、 testmethod is calculated to determine the shedding characteristicof the test sample.3. Significance and Use3.1 During the application of coatings, paint brushes canexhibit shedding of filling material onto the coated surface. Ameasure of this shedding filling material will determine thepaint brushs

6、 ability to resist shedding during application.4. Equipment4.1 Standard Large Brush Making Comb, typically with awood handle and steel teeth (see Fig. 1). Teeth approximately.88 in. (22.2 mm) long; teeth portion of comb approximately 36teeth at 4.14 in. (105.1 mm), resulting in .15 in. (2.9 mm) toot

7、hspacing; tooth diameter approximately .048 in. (1.2 mm); 4.75in. (120.7 mm) comb length-out from handle.4.2 Standard White Paper, 8.5 by 11 in. (215.9 by 279.4mm).5. Sampling, Test Specimens, and Test Units5.1 Sample three identical brushes per test.6. Procedure6.1 Hold the brush test specimen over

8、 the white paper withthe filling material facing downward toward the paper at abouta 45 angle and at a distance of 5 to 6 in. (127 to 152.4 mm)above the paper.6.2 Check that the entire filling material is over the papersurface.6.3 Insert the teeth of the comb as deep as possible, atapproximately one

9、 third of the filling material length clear fromferrule edge.6.4 Push the comb through the filling material until the teethexit the tip of brush at about one stroke per second.6.5 Repeat steps 6.3 and 6.4 ten (10) times on each widthside of the brush.6.6 Pull out any visible filling material that ar

10、e protrudingfrom the brush tip by hand and place on the paper.6.7 Continue to follow steps 6.3 and 6.4 five (5) times oneach thickness side of the brush.6.8 Pull out any visible filling material that are protrudingfrom the brush tip by hand and place on the paper.6.9 Fan the tip of the brush back an

11、d forth with the combfive times along the width direction and pull out any remainingloose filling material protruding from the brush tip. Theamount of depth that the tines must penetrate the brush tip isequal to the length of the tine or .88 in. (22.2 mm) deep asrecommended in 4.1.6.10 Count the num

12、ber of filling material pieces that aregreater than 0.5 in. (12.7 mm) and record. Smaller pieces andbroken tips can be estimated visually and noted.7. Precision and Bias7.1 At the time of the study, there was no accepted referencematerial suitable for determining the bias for this test method.Theref

13、ore no statement of bias is being made.8. Keywords8.1 brush ferrule; brush filling material; length clear1This test method is under the jurisdiction of ASTM Committee D01 on Paintand Related Coatings, Materials, and Applications and is the direct responsibility ofSubcommittee D01.61 on Paint Applica

14、tion Tools.Current edition approved June 1, 2013. Published July 2013. Originally approvedin 2012. Last previous edition approved in 2012 as D7834 12. DOI: 10.1520/D7834-13.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1ASTM Internat

15、ional takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely the

16、ir own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should

17、be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standar

18、ds, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).FIG. 1 Large Brush Making CombD7834 132