ASTM D6447-2009(2014) 9745 Standard Test Method for Hydroperoxide Number of Aviation Turbine Fuels by Voltammetric Analysis《用伏安测量分析法测定航空涡轮机燃料中氢过氧化物值的标准试验方法》.pdf

《ASTM D6447-2009(2014) 9745 Standard Test Method for Hydroperoxide Number of Aviation Turbine Fuels by Voltammetric Analysis《用伏安测量分析法测定航空涡轮机燃料中氢过氧化物值的标准试验方法》.pdf》由会员分享，可在线阅读，更多相关《ASTM D6447-2009(2014) 9745 Standard Test Method for Hydroperoxide Number of Aviation Turbine Fuels by Voltammetric Analysis《用伏安测量分析法测定航空涡轮机燃料中氢过氧化物值的标准试验方法》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D6447 09 (Reapproved 2014)Standard Test Method forHydroperoxide Number of Aviation Turbine Fuels byVoltammetric Analysis1This standard is issued under the fixed designation D6447; the number immediately following the designation indicates the year oforiginal adoption or, in the case of

2、revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 The test method covers the determination of the hydrop-eroxide content of aviation turbine fuels

3、. The test method mayalso be applicable to the determination of the hydroperoxidecontent of any water-insoluble, organic fluid, particularlydiesel fuels, gasolines, and kerosines.1.2 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstanda

4、rd.1.3 This standard does not purport to address all the safetyconcerns, if any, associated with its use. It is the responsibilityof the user of this standard to consult and establish appropriatesafety and health practices and determine the applicability ofregulatory limitations prior to use. For sp

5、ecific warningstatements, see 6.3 6.5, Annex A1, and Annex A2.2. Referenced Documents2.1 ASTM Standards:2D1193 Specification for Reagent WaterD3703 Test Method for Hydroperoxide Number of AviationTurbine Fuels, Gasoline and Diesel FuelsD4057 Practice for Manual Sampling of Petroleum andPetroleum Pro

6、ducts3. Summary of Test Method3.1 A quantity of sample is contacted with aqueous potas-sium iodide solution in the presence of acid. The hydroperox-ides present are reduced by the potassium iodide. An equiva-lent amount of iodine is liberated, which is quantified byvoltammetric analysis. The results

7、 are calculated and reportedas millimoles (mmole) of hydroperoxide per litre of sample.4. Significance and Use4.1 This test method and Test Method D3703 measure thesame peroxide species (primarily hydroperoxides) in aviationfuels.4.2 The magnitude of the hydroperoxide number is anindication of the q

8、uantity of oxidizing constituents present.Deterioration of fuel results in the formation of hydroperoxidesand other oxygen-carrying compounds. The hydroperoxidenumber measures those compounds that will oxidize potassiumiodide.4.3 The determination of the hydroperoxide number of fuelsis significant b

9、ecause of the adverse effect of hydroperoxidesupon certain elastomers in the fuel systems.5. Apparatus5.1 Voltammetric Analyzer3The instrument used to quan-tify the liberated iodine is a voltammetric analyzer equippedwith a three electrode system and a digital or analog output.The combination electr

10、ode system (see Fig. 1) consists of aglassy carbon disc (3-mm diameter) working electrode, aplatinum wire (0.5 mm diameter) auxiliary electrode, and aplatinum wire (0.5 mm diameter) reference electrode. Thevoltammetric analyzer applies a linear voltage ramp (0 to 1 Vrange with respect to the referen

11、ce electrode) at a rate of 0.1V/s to the auxiliary electrode. The current output of theworking electrode is converted to voltage by the voltammetricanalyzer, using the gain ratio of 1V/20A. The peak height orpeak area of the voltammetric response to iodine is outputted toan analog or digital recordi

12、ng device (0 to 1 V full scale).5.2 Vortex Mixer,4with a 2800 to 3000 rpm motor and a padsuitable for mixing test tubes and vials.5.3 Pipette, or equivalent, capable of delivering volumesrequired in the test method, such as 0.2, 1, and 2 mL.1This test method is under the jurisdiction of ASTM Committ

13、ee D02 onPetroleum Products, Liquid Fuels, and Lubricantsand is the direct responsibility ofSubcommittee D02.05 on Properties of Fuels, Petroleum Coke and Carbon Material.Current edition approved May 1, 2014. Published July 2014. Originally approvedin 1999. Last previous edition approved in 2009 as

14、D6447 09. DOI: 10.1520/D6447-09R14.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Voltammetric analyzers sp

15、ecifically designed to perform hydroperoxide valuedeterminations of aviation turbine fuels are commercially available from TheUniversity of Dayton Research Institute. Voltammographs, which can be set up toperform hydroperoxide value determinations of aviation turbine fuels, are availablefrom BAS, We

16、st Lafayette, IN and EG hydroperoxide number; perox-ideANNEXES(Mandatory Information)A1. MATERIAL WARNING STATEMENTSA1.1 Hydrochloric Acid (concentrated)(WarningPoison. Corrosive. Can be fatal if swallowed. Causes severeburns. Harmful if inhaled.)A1.2 Acetic Acid (glacial)(WarningPoison. Corrosive.C

17、ombustible. May be fatal if swallowed. Causes severe burns.Harmful if inhaled.)A1.3 Potassium Dichromate(WarningPoison. Can befatal if swallowed.Avoid contact with eyes and skin, and avoidbreathing of dust. Strong oxidizer. Possible cancer hazard.)A2. PRECAUTIONARY HANDLING STATEMENTSA2.1 The follow

18、ing safety precautions should be followedin handling the materials listed in Annex A1.A2.1.1 Do not get in eyes, on skin, or on clothing.A2.1.2 Do not breathe vapor, spray, or mist.A2.1.3 Dilute by addition of acid to water.A2.1.4 Keep away from heat and open flame.A2.1.5 Keep in tightly closed cont

19、ainer in approved storagecabinet.A2.1.6 Keep cool.A2.1.7 Loosen closure carefully when opening.A2.1.8 Use with adequate ventilation.A2.1.9 Keep container closed when not in use.A2.1.10 Use protective clothing and goggles when han-dling.A2.1.11 Wash thoroughly after handling.ASTM International takes

20、no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own respo

21、nsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed

22、 to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the a

23、ddress shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone

24、), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ data have been filed at ASTM International Headquarters and maybe obtained by requesting Research Report RR:D02-1630.D6447 09 (2014)4