ASTM D5807-2008(2013) 2500 Standard Practice for Evaluating the Overpressurization Characteristics of Inflatable Restraint Cushions《评估可充气缓冲垫过压特性的标准实施规程》.pdf

《ASTM D5807-2008(2013) 2500 Standard Practice for Evaluating the Overpressurization Characteristics of Inflatable Restraint Cushions《评估可充气缓冲垫过压特性的标准实施规程》.pdf》由会员分享，可在线阅读，更多相关《ASTM D5807-2008(2013) 2500 Standard Practice for Evaluating the Overpressurization Characteristics of Inflatable Restraint Cushions《评估可充气缓冲垫过压特性的标准实施规程》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D5807 08 (Reapproved 2013)Standard Practice forEvaluating the Overpressurization Characteristics ofInflatable Restraint Cushions1This standard is issued under the fixed designation D5807; the number immediately following the designation indicates the year oforiginal adoption or, in the

2、case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice covers the procedures and conditions usedto evaluate the physical performa

3、nce of inflatable restraintcushions during and after overpressurization testing at elevatedpressures capable of causing cushion bursting using air pres-surization equipment.1.2 The physical performance characteristics that may beobtained in conjunction with this practice are internal cushionpressure

4、s determined by instrumentation and material integrity,determined by visual inspection.1.3 This practice is applicable to all inflatable restraintcushions.1.4 Procedures and apparatus other than those stated in thispractice may be used by agreement between purchaser andsupplier with the specific dev

5、iations from this practice ac-knowledged in the report.1.5 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard. The values stated ineach system are not exact equivalents; therefore, each systemmust be used independently of the other.1.6 This standard doe

6、s not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use. See Section 8 forspecific hazard in

7、formation.2. Referenced Documents2.1 ASTM Standards:2D123 Terminology Relating to TextilesD6799 Terminology Relating to Inflatable Restraints3. Terminology3.1 Definitions:3.2 For all terminology relating to D13.20, InflatableRestraints, refer to Terminology D6799.3.2.1 The following terms are releva

8、nt to this standard:cushion, cushion overpressurization, deployment, inflatablerestraint, module, standard atmosphere for testing textiles.3.3 For all other terms related to textiles, see TerminologyD123.4. Summary of Practice4.1 Inflatable restraint cushions are tested under laboratoryconditions to

9、 evaluate cushion integrity when exposed tointernal cushion pressures greater than deployment pressures.If cushion rupture occurs, the rupture pressure, time to rupture,and mode of rupture are recorded.4.2 Inflatable restraint cushions are mounted into a teststand that allows for inflations under co

10、nditions that exceeddeployment pressures. Instrumentation within the test standcharts inflation pressures versus time and may allow forphotographic review of the overpressurization sequence.4.3 Cushion overpressurization results are reviewed forpressure and time relationships, and post-inflation mat

11、erialanalysis.5. Significance and Use5.1 This practice is intended to be a general guideline forrepetitive testing, safe conduct of tests, and accurate datacollection for inflatable restraints. Cushion overpressurizationtesting may be used for design and production validation, formanufacturing proce

12、ss control, for lot acceptance, or for acombination thereof.5.2 This practice constitutes the conditions, apparatus, andprocedures by which inflatable restraints are commonly testedfor cushion overpressurization. It is intended to be used as aguideline in establishing a cushion specification or equi

13、valentdocument. The practices in the specification may deviate fromthe practices described herein when (based on experience)considerations of equipment, cushion design, or other factorsdictate otherwise.1This practice is under the jurisdiction ofASTM Committee D13 on Textiles andis the direct respon

14、sibility of Subcommittee D13.20 on Inflatable Restraints.Current edition approved July 1, 2013. Published September 2013. Originallyapproved in 1995. Last previous edition approved in 2008 as D5807 08. DOI:10.1520/D5807-08R13.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orco

15、ntact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States15.3 There exists a la

16、rge variety in cushion configurationsand equipment designs, obviating a standard test method forcushion overpressurization. Therefore, a cushion specificationshould incorporate the practices stated herein when describinga test method for testing a specific cushion geometry andapparatus design. To en

17、sure accuracy and repeatability, thespecification should also address precision and bias in amanner consistent with ASTM prescribed procedures andconsistent with the particular cushion geometry, equipment inuse, and test procedures.5.3.1 Sources of variation in cushion overpressurizationtesting proc

18、edures include orifice size, attachment fixture,sensor location, method of attachment, presence or absence ofinternal bladder, accumulator size and pressure, transducertype and location, the presence or absence of tethers, presenceor absence of vent plugs, and the accuracy of timing devicesand press

19、ure sensors. All sources of equipment and proceduralvariation should be addressed in the applicable specification.5.4 In accordance with the applicable specification, cush-ions may be pressurized without bursting to determine theirresistance to a fixed level of high internal pressure, or they maybe

20、subjected to increasing pressures to determine their ultimatebursting strength.6. Apparatus6.1 Plastic Liner Bags, with a combined bursting strength of3.5 kPa (0.5 psi) or less for use as optional bladders to aid inthe bursting of cushions whose fabric permeability is too highto permit ultimate burs

21、ting strength testing without them.6.2 Patches or Plugs, to seal cushion vents, if cushionbursting is required and cushion overpressurization testingequipment does not provide the required air volume forbursting.6.3 Pressure Vessel, capable of being charged pneumaticallyfrom 0 to no less than 865 kP

22、a (0 to no less than 125 psi) witha tolerance of 63 %, of sufficient volume to adequatelychallenge the volume of the cushion being tested, and equippedwith intake and outlet air lines and a quick-release solenoidvalve.6.4 Mounting Fixture, capable of retaining the cushionassembly by its attachment p

23、oints without damaging thecushion material, in an orientation for free expansion of thecushion geometry, and with sufficient shielding for operatorprotection if the cushion overpressurization testing unit is notphysically isolated in a separate room from the operator duringactuation.6.5 Pressure Tra

24、nsducer and Pickup Tube, suitable formeasuring pressures inside the cushion from 0700 kPa (0100psi) with a tolerance of 63 %, mounted in a static or lowpressure area in the test fixture that does not interfere withcushion overpressurization.6.6 Data Acquisition System, suitable for recording theoutp

25、ut of the pressure transducer versus elapsed time ofoverpressurization (optional).6.6.1 Filter requirements, data sampling rate, transducerfrequency response, and amplifier frequency response shall besuch that minimal effect on accuracy of the data occurs.Overall accuracy of the data acquisition sys

26、tem shall be within63%.6.7 Electrical Firing Pulse Source, suitable for actuating theinflation and for communicating with the data acquisitionsystem dependent on an electrical signal.6.8 Film or Tape Video System, suitable for recording thecushion geometry or mode of rupture during overpressurizatio

27、nat 1000 or more frames per second, and capable of beingsynchronized precisely with a firing pulse (optional).6.9 Lighting System, suitable for high resolution photogra-phy (optional).7. Interferences7.1 The pressure transducer and/or pickup tube within themounting fixture must be mounted in a posit

28、ion that does notinterfere with the unfolding cushion.7.2 The pressure versus time data is subject to recordinganomalies and electronic noise. The data should be digitallyfiltered to obtain the underlying smooth pressure curve prior todata analysis.8. Hazards8.1 Personnel conducting cushion overpres

29、surization testingin the same room as the testing unit must be equipped with theappropriate safety equipment and safety training. Examples ofthe necessary safety equipment include, but are not limited to,ear protection, equipment shielding, and safety glasses. Properwritten safety procedures shall b

30、e provided to all test personnelfor compliance with standard industry practices. There shall becompliance to all applicable Occupational Safety and HealthAssociation (OSHA) standards.9. Sampling9.1 Cushion overpressurization testing is a destructive testand therefore necessitates sampling procedures

31、 if used inconjunction with lot acceptance.9.2 For acceptance testing, the lot size is the quantity ofcushions sewn on one production line in one production day.9.3 Lot SampleFor acceptance testing, take at random thenumber of cushions directed in an applicable cushion specifi-cation or other agreem

32、ent between purchaser and supplier.Consider cushions to be the primary sampling units.9.4 Each cushion in the lot sample is a test specimen.10. Equipment Calibration10.1 For inflatable restraints, all test equipment used inaccordance with this practice shall be certified for calibrationannually by a

33、n independent agency or equipment manufacturerwhose results are traceable to the National Institute of Scienceand Technology (NIST) or other national standards laboratory.The test parameters of the equipment shall be tested within theoperating ranges covered in the cushion specification orequivalent

34、 document.D5807 08 (2013)211. Conditioning11.1 Conditioning of specimens for cushion overpressuriza-tion testing is conducted at the standard atmosphere for testingtextiles for at least 4 h prior to test.12. Procedures12.1 Select and condition cushion specimens in accordancewith Sections 11 and 9.12

35、.2 If cushion bursting is intended and cushion overpres-surization testing equipment does not provide the required airvolume for bursting, seal the cushion vents with a plug or witha sewn fabric patch made of the same material as the cushion.12.3 Mount the cushion specimen on the test fixture, ensur

36、-ing that the retention mechanism does not damage the cushionmaterial, and that the pressure transducer and pickup tube donot interfere with the inflation of the cushion.12.4 Install a protective screen around the test fixture, ifneeded.12.5 Perform all system calibrations.12.6 Verify proper framing

37、 rate, camera settings, and light-ing intensity levels, if needed.12.7 Enter the test serial number into recording portions ofthe data acquisition and video systems.12.8 Ensure the pressure vessel is pressurized sufficiently toevaluate the cushion under test.12.9 Turn on the warning light before arm

38、ing the pressur-ization switch.12.10 Initiate the starting sequence and note the response ofthe data acquisition system to verify successful pressurization.12.11 Pressurize the cushion until it reaches the pre-setinternal pressure or until it ruptures, as specified.12.12 Record test measurements suc

39、h as maximum cushionpressure in kPa (psi), time to maximum cushion pressure inm/s, or the location and nature of the cushion rupture, asspecified.12.13 De-arm the starting switch and remove the cushionfrom the test stand.13. Report13.1 State that the tests were conducted in accordance withPractice D

40、5807 for evaluating the overpressurization charac-teristics of inflatable restraint cushions.13.1.1 If deviation from Practice D5807 occurred, anyreference to this practice shall state: “Testing was performed inaccordance with Practice D5807, with the following changes:13.2 The purchaser and supplie

41、r determine the exact form ofthe test report. Unless otherwise specified, the form shallprovide the following information:13.2.1 Cushion designation(s),13.2.2 Lot identification,13.2.3 Date of report,13.2.4 Name of person certifying report,13.2.5 Relevant specification,13.2.6 Number of specimens use

42、d in each test,13.2.7 Tests performed and data obtained,13.2.8 Laboratory conditions if other than standard, and13.2.9 Deviations from standard procedures and apparatus.14. Keywords14.1 airbag; bag burst; cushion; inflatable restraint; ruptureASTM International takes no position respecting the valid

43、ity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subje

44、ct to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquart

45、ers. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard

46、 is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D5807 08 (2013)3