ASTM D4946-1989(2012) Standard Test Method for Blocking Resistance of Architectural Paints《建筑涂料耐结块的标准试验方法》.pdf
《ASTM D4946-1989(2012) Standard Test Method for Blocking Resistance of Architectural Paints《建筑涂料耐结块的标准试验方法》.pdf》由会员分享,可在线阅读,更多相关《ASTM D4946-1989(2012) Standard Test Method for Blocking Resistance of Architectural Paints《建筑涂料耐结块的标准试验方法》.pdf(2页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: D4946 89 (Reapproved 2012)Standard Test Method forBlocking Resistance of Architectural Paints1This standard is issued under the fixed designation D4946; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last
2、revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers an accelerated procedure forevaluating the face-to-face blocking resistance of trades salespaints.
3、This is not to be confused with blocking resistance TestMethod D3003, which is concerned with blocking of industrialcoatings on metal substrates, nor with Test Method D2793which is concerned specifically with wood product finishes andreports results on a satisfactory or not satisfactory basis, rathe
4、rthan by the degree of blocking tendency as in this test method.1.2 The values stated in the SI units of measurement are tobe regarded as the standard. The values given in parenthesesare for information only.1.3 This standard does not purport to address all of thesafety concerns, if any, associated
5、with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D16 Terminology for Paint, Related Coatings, Materials, andAppli
6、cationsD2793 Test Method for Block Resistance of Organic Coat-ings on Wood Panel SubstratesD3003 Test Method for Pressure Mottling and BlockingResistance of Organic Coatings on Metal Substrates3. Terminology3.1 Definitions:3.1.1 blocking, nthe undesirable sticking together of twopainted surfaces whe
7、n pressed together or placed in contactwith each other for an extended period of time, as referenced inTerminology D16.4. Summary of Test Method4.1 Dried paint films are placed face-to-face and a pressureof about 127 g/cm2(1.8 psi) is applied. These paint films areput into an oven for 30 min to make
8、 the test more stringent.After cooling, the blocked panels are peeled apart. The degreeof blocking is rated subjectively for tack or seal using a seriesof standard descriptive terms corresponding to numericalASTM values of 10 to 0.5. Significance and Use5.1 Dry paint often comes in contact with itse
9、lf especially inwindow and door areas and, depending on its hardness, thepressure, temperature, humidity, and duration of time thesurfaces are in contact, sometimes sticks to itself (blocks). Thisstringent test method can be used to compare and ratesubjectively the resistance of paints to blocking.6
10、. Apparatus6.1 Conditioned Room, at 18 to 29.5C (65 to 85F) and 40to 60 % relative humidity.6.2 Sealed Paper Test Charts, approximately 190 by 280mm (7.5 by 11 in.).6.3 Applicator Blade, 13 to 15 cm (5 to 6 in.) wide,0.15-mm (6-mil) clearance.6.4 Oven, 48 to 52C (115 to 125F).6.5 Rubber Stoppers, No
11、. 8, 3.2 cm (1.25 in.) smallerdiameter.6.6 Weights, 1000 g.6.7 Scissors.6.8 Aluminum Tray or Pan, flat.7. Procedure7.1 Cast the paint to be tested on a sealed test chart using theapplicator blade. Condition coated panels in the conditionedroom for seven days. All painted panels should be kept free o
12、fgrease, oil, or fingerprints since these will affect block resis-tance.7.2 After the panels have been conditioned, cut out six 3.8by 3.8-cm (112 by 112-in.) sections from the painted chart.Start the cut at least 1.3 cm (12 in.) away from the edge of thedrawdown.1This test method is under the jurisd
13、iction of ASTM Committee D01 on Paintand Related Coatings, Materials, and Applications and is the direct responsibility ofSubcommittee D01.42 on Architectural Coatings.Current edition approved July 1, 2012. Published September 2012. Originallyapproved in 1989. Last previous edition approved in 2008
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMD494619892012STANDARDTESTMETHODFORBLOCKINGRESISTANCEOFARCHITECTURALPAINTS 建筑 涂料 结块 标准 试验 方法 PDF

链接地址:http://www.mydoc123.com/p-518474.html