ASTM D1831-2011 Standard Test Method for Roll Stability of Lubricating Grease《润滑脂滚轧稳定性的标准试验方法》.pdf
《ASTM D1831-2011 Standard Test Method for Roll Stability of Lubricating Grease《润滑脂滚轧稳定性的标准试验方法》.pdf》由会员分享,可在线阅读,更多相关《ASTM D1831-2011 Standard Test Method for Roll Stability of Lubricating Grease《润滑脂滚轧稳定性的标准试验方法》.pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: D1831 11Standard Test Method forRoll Stability of Lubricating Grease1This standard is issued under the fixed designation D1831; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in par
2、entheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 This test method covers determination of the changes inthe consiste
3、ncy, as measured by cone penetration, of lubricat-ing greases when worked in the roll stability test apparatus.1.2 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.2.1 ExceptionThe values stated in inch-pound units forthe appar
4、atus dimensions are to be regarded as standard; the SIconversions are provided for information only.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and heal
5、th practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D217 Test Methods for Cone Penetration of LubricatingGreaseD1403 Test Methods for Cone Penetration of LubricatingGrease Using One-Quarter and One-Half Scale ConeEquipmentD4
6、175 Terminology Relating to Petroleum, PetroleumProducts, and Lubricants3. Terminology3.1 Definitions:3.1.1 consistency, nof lubricating grease, the degree ofresistance to movement under stress.3.1.1.1 DiscussionThe term consistency is used some-what synonymously with penetration. Generally, consist
7、encyrefers to the worked penetration of a grease. D2173.1.2 lubricant, nany material interposed between twosurfaces that reduces the friction or wear between them.D41753.1.3 lubricating grease, na semi-fluid to solid product ofa dispersion of a thickener in a liquid lubricant.3.1.3.1 DiscussionThe d
8、ispersion of the thickener forms atwo-phase system and immobilizes the liquid lubricant bysurface tension and other physical forces. Other ingredientsimparting special properties are often included. D2173.1.4 penetration, nof lubricating grease, the depth thatthe standard cone, when released to fall
9、 under its own weightfor 5 s, enters the sample. D2173.1.5 thickener, nin lubricating grease, a substance com-posed of finely divided particles dispersed in a liquid lubricantto form the products structure.3.1.5.1 DiscussionThe thickener can be fibers (such asvarious metallic soaps) or plates or sph
10、eres (such as certainnon-soap thickeners) which are insoluble or, at the most, onlyvery slightly soluble in the liquid lubricant. The generalrequirements are that the solid particles be extremely small,uniformly dispersed, and capable of forming a relatively stable,gel-like structure with the liquid
11、 lubricant. D2173.1.6 worked penetration, nof lubricating grease, thepenetration at 25C (77F), without delay, of a sample after 60double strokes in a standard grease worker. D2173.1.7 working, nof lubricating grease, the subjection of asample to the shearing action of the standard grease worker.D217
12、3.2 Definitions of Terms Specific to This Standard:3.2.1 roll stability, nof lubricating grease, the change inconsistency of a sample after a specified amount of working ina test apparatus utilizing a weighted roller inside a rotatingcylinder.4. Summary of Test Method4.1 The Test Methods D1403 cone
13、penetration of an ap-proximately 50-g aliquot of lubricating grease is determined.The grease is then subjected to low shear at 20 to 35C for 2h 6 5 min in a standard roll stability apparatus, before the conepenetration is again measured. The difference between the cone1This test method is under the
14、jurisdiction of ASTM Committee D02 onPetroleum Products and Lubricants and is the direct responsibility of SubcommitteeD02.G0.02 on Consistency and Related Rheological Tests.Current edition approved Jan. 1, 2011. Published January 2011. Originallyapproved in 1961. Last previous edition approved in 2
15、006 as D183100(2006).DOI: 10.1520/D1831-11.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM In
16、ternational, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.penetration before working and the cone penetration after isused as a measure of the effect of low shear working on greaseconsistency.5. Significance and Use5.1 The roll stability test is widely used in
17、specifications.Test results are significant insofar as they can show a direc-tional change in consistency that could occur in service. Noaccurate correlation is established between the test results andshear stability in actual service.6. Apparatus6.1 Roll Stability Test Apparatus, capable of rotatin
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMD18312011STANDARDTESTMETHODFORROLLSTABILITYOFLUBRICATINGGREASE 润滑脂 稳定性 标准 试验 方法 PDF
![提示](http://www.mydoc123.com/images/bang_tan.gif)
链接地址:http://www.mydoc123.com/p-510533.html