ASTM C1766-2015 Standard Specification for Factory-Laminated Gypsum Panel Products《工厂-层压石膏心墙板产品的标准规格》.pdf
《ASTM C1766-2015 Standard Specification for Factory-Laminated Gypsum Panel Products《工厂-层压石膏心墙板产品的标准规格》.pdf》由会员分享,可在线阅读,更多相关《ASTM C1766-2015 Standard Specification for Factory-Laminated Gypsum Panel Products《工厂-层压石膏心墙板产品的标准规格》.pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: C1766 13C1766 15Standard Specification forFactory-Laminated Gypsum Panel Products1This standard is issued under the fixed designation C1766; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A
2、number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers the factory-laminated gypsum panel products designed either for use on walls, ceilings, orpartitions as part
3、of a sound control system; or for use as a gypsum stud or gypsum coreboard.1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI unitsare shown in brackets. The values stated in each system may not be exact equivalents; theref
4、ore, each system shall be usedindependently of the other. Combining values from the two systems may result in non-conformance with the standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibilityof the user of this stand
5、ard to establish appropriate safety and health practices and determine the applicability of regulatorylimitations prior to use.2. Referenced Documents2.1 ASTM Standards:2C11 Terminology Relating to Gypsum and Related Building Materials and SystemsC473 Test Methods for Physical Testing of Gypsum Pane
6、l ProductsC1264 Specification for Sampling, Inspection, Rejection, Certification, Packaging, Marking, Shipping, Handling, and Storage ofGypsum Panel ProductsC1278 Specification for Fiber-Reinforced Gypsum PanelC1396 Specification for Gypsum BoardC1658 Specification for Glass Mat Gypsum PanelsE84 Tes
7、t Method for Surface Burning Characteristics of Building MaterialsE119 Test Methods for Fire Tests of Building Construction and Materials3. Terminology3.1 Definitions used in this specification shall be in accordance with Terminology C11.4. Materials and Manufacture4.1 Factory-laminated gypsum panel
8、 products shall be composed of two or more gypsum panel products factory-laminated intoa composite panel.4.1.1 The individual gypsum panel products shall comply with Specification C1278, Specification C1396, or SpecificationC1658.4.2 Laminating adhesive shall be applied to either one or both of the
9、surfaces being laminated.4.3 Factory-laminated gypsum panel products shall have a flame spread index of not more than 25 when tested in accordancewith Test Method E84.4.4 Factory-laminated gypsum panel products, type X (Special Fire-Resistant):4.4.1 Factory-laminated gypsum panel products, type X, d
10、esignates factory-laminated gypsum panel products complying withthis specification that provides not less than 1 h fire-resistance rating for panels 58 in. 15.9 mm thick or 34 h fire-resistance rating1 This test method is under the jurisdiction of ASTM Committee C11 on Gypsum and Related Building Ma
11、terials and Systems and is the direct responsibility ofSubcommittee C11.01 on Specifications and Test Methods for Gypsum Products.Current edition approved June 15, 2013Feb. 1, 2015. Published August 2013February 2015. Originally approved in 2013. Last previous edition approved in 2013 asC1766 13. DO
12、I: 10.1520/C176613.10.1520/C176615.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.This document is not an AS
13、TM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In a
14、ll cases only the current versionof the standard as published by ASTM is to be considered the official document.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1for panels 12 in. 12.7 mm thick, applied parallel with and on each side of
15、 load bearing 2 by 4 wood studs spaced 16 in. 406 mmon centers with 6d coated nails, 178-in. 48-mm long, 0.0915-in. 2.3-mm diameter shank, 14-in. 6.4-mm diameter heads, spaced7 in. 178 mm on centers with gypsum panel joints staggered 16 in. 406 mm on each side of the partition and tested inaccordanc
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMC17662015STANDARDSPECIFICATIONFORFACTORYLAMINATEDGYPSUMPANELPRODUCTS 工厂 层压 石膏 心墙板 产品 标准 规格 PDF

链接地址:http://www.mydoc123.com/p-465771.html