ASTM C1440-2008(2013)e1 Standard Specification for Thermoplastic Elastomeric (TPE) Gasket Materials for Drain Waste and Vent (DWV) Sewer Sanitary and Storm Plumbing Systems《雨水、废物和通.pdf
《ASTM C1440-2008(2013)e1 Standard Specification for Thermoplastic Elastomeric (TPE) Gasket Materials for Drain Waste and Vent (DWV) Sewer Sanitary and Storm Plumbing Systems《雨水、废物和通.pdf》由会员分享,可在线阅读,更多相关《ASTM C1440-2008(2013)e1 Standard Specification for Thermoplastic Elastomeric (TPE) Gasket Materials for Drain Waste and Vent (DWV) Sewer Sanitary and Storm Plumbing Systems《雨水、废物和通.pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: C1440 08 (Reapproved 2013)1Standard Specification forThermoplastic Elastomeric (TPE) Gasket Materials for Drain,Waste, and Vent (DWV), Sewer, Sanitary and StormPlumbing Systems1This standard is issued under the fixed designation C1440; the number immediately following the designation in
2、dicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1NOTEEditorial changes were made throughout in Octob
3、er 2013.1. Scope1.1 This specification covers thermoplastic elastomeric(TPE) gasket materials for preformed elastomeric gaskets usedin shielded and non-shielded mechanical couplings. Thesecouplings are used in gravity flow drain, waste and vent(DWV), sewer, sanitary and storm plumbing systems. Theyi
4、nclude couplings to join similar and dissimilar piping sizesand material.1.2 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 This sta
5、ndard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1
6、ASTM Standards:2A644 Terminology Relating to Iron CastingsD395 Test Methods for Rubber PropertyCompression SetD412 Test Methods for Vulcanized Rubber and Thermoplas-tic ElastomersTensionD471 Test Method for Rubber PropertyEffect of LiquidsD573 Test Method for RubberDeterioration in an AirOvenD624 Te
7、st Method for Tear Strength of Conventional Vul-canized Rubber and Thermoplastic ElastomersD1149 Test Methods for Rubber DeteriorationCracking inan Ozone Controlled EnvironmentD1415 Test Method for Rubber PropertyInternationalHardnessD2240 Test Method for Rubber PropertyDurometer Hard-nessD5964 Prac
8、tice for Rubber IRM 901, IRM 902, and IRM903 Replacement Oils forASTM No. 1, ASTM No. 2, andASTM No. 3 Oils3. Terminology3.1 DefinitionsRefer to Terminology A644 for definitionsof the following terms used in this specification elastomer,elastomeric, elongation, gasket, hardness, preformed gasket-(se
9、e gasket), thermoplastic elastomer.4. Materials and Manufacture4.1 Gaskets shall be made of virgin thermoplastic elasto-meric compound containing only clean reworked thermoplasticelastomer material from the manufacturers own production ofthe same compound.4.2 Where splices are made in the gasket, th
10、e strength of thesplice shall be such that the gasket will withstand the stretchtest described in 8.9 with no visible separation or peeling.4.3 Many thermoplastic elastomeric materials (TPE) aretemperature sensitive. Designed operating temperature rangefor the 87 Shore A TPE materials is 0 to 130 F
11、(18 to55C). These materials are not designed or intended forprolonged operation outside this range.5. Physical Properties5.1 Gaskets representative of the manufacturers productionshall be selected as specified in Section 7 and shall conform tothe requirements for physical properties listed in Table
12、1 whentested in accordance with the methods specified in Section 8.6. Workmanship, Finish, and Appearance6.1 The surface of the gasket shall be smooth and free ofpitting, cracks, blisters, air marks, and any other imperfections1This Specification is under the jurisdiction of ASTM Committee A04 on Ir
13、onCastings and is the direct responsibility of Subcommittee A04.75 on Gaskets andCoupling for Plumbing and Sewer Piping.Current edition approved May 1, 2013. Published May 2013. Originallyapproved in 1999. Last previous edition approved in 2008 as C1440 08. DOI:10.1520/C1440-08R13.2For referenced AS
14、TM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshoho
15、cken, PA 19428-2959. United States1that will affect its behavior in service. The body of the gasketshall be free of porosity and air pockets.6.2 Neither the flash thickness nor the flash extension shallexceed 1/32 in. (0.8 mm), at any point on the ring.6.3 The offset, or failure of the mold to regis
16、ter accurately,shall not exceed 1/64 in. (0.4 mm).7. Sampling7.1 For the stretch test specified in 8.9, sample gaskets shallbe selected at random from each shipment of gaskets. For eachof the other tests, gaskets shall be selected at random asrequired by the method of test specified.8. Test Methods8
17、.1 HardnessTest the gasket material for hardness inaccordance with Test Method D2240. As required, use TestMethod D1415 as the referee method. Make hardness measure-ments on specimens prepared in accordance with 8.2.However, hardness readings for guidance purposes shall betaken directly on the gaske
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMC144020082013E1STANDARDSPECIFICATIONFORTHERMOPLASTICELASTOMERICTPEGASKETMATERIALSFORDRAINWASTEANDVENTDWVSEWERSANITARYANDSTORMPLUMBINGSYSTEMS
链接地址:http://www.mydoc123.com/p-464686.html