ASTM A29 A29M-2016 Standard Specification for General Requirements for Steel Bars Carbon and Alloy Hot-Wrought《热锻碳和合金钢棒通用要求的标准规格》.pdf

《ASTM A29 A29M-2016 Standard Specification for General Requirements for Steel Bars Carbon and Alloy Hot-Wrought《热锻碳和合金钢棒通用要求的标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM A29 A29M-2016 Standard Specification for General Requirements for Steel Bars Carbon and Alloy Hot-Wrought《热锻碳和合金钢棒通用要求的标准规格》.pdf（19页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: A29/A29M 15A29/A29M 16Standard Specification forGeneral Requirements for Steel Bars, Carbon and Alloy,Hot-Wrought1This standard is issued under the fixed designation A29/A29M; the number immediately following the designation indicates the yearof original adoption or, in the case of revi

2、sion, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope*1.1 This specific

3、ation2 covers a group of common requirements which, unless otherwise specified in the purchase order or inan individual specification, shall apply to carbon and alloy steel bars under each of the following ASTM specifications (or underany other ASTM specification which invokes this specification or

4、portions thereof):Title of Specification ASTMDesignationAHot-Rolled Carbon Steel Bars:Steel Bars, Carbon, Quenched and Tempered A321Steel Bars and Shapes, Carbon Rolled from “T Rails A499Steel Bars, Carbon, Merchant Quality, M-Grades A575Steel Bars, Carbon, Hot-Wrought, Special Quality A576Steel Bar

5、s, Carbon, Merchant Quality, MechanicalPropertiesA663/A663MSteel Bars, Carbon, Hot-Wrought, Special Quality, Me-chanical PropertiesA675/A675MSteel Bars for Springs, Carbon and Alloy A689Cold-Finished Carbon Steel Bars:Steel Bars, Carbon and Alloy, Cold-Finished A108Cold-Drawn Stress-Relieved Carbon

6、Steel Bars Sub-ject to Mechanical Property RequirementsA311/A311MHot-Rolled Alloy Steel Bars:Steel Bars, Alloy, Standard Grades A322Carbon and Alloy Steel Bars Subject to End-QuenchHardenability RequirementsA304Steel Bars, Alloy, Hot-Wrought or Cold-Finished,Quenched and TemperedA434/A434MSteel Bars

7、, Alloy, Hot-Wrought, for Elevated Tempera-ture or Pressure-Containing Parts, or BothA739Cold-Finished Alloy Steel Bars:Steel Bars, Alloy, Hot-Rolled or Cold-Finished,Quenched and TemperedA434/A434MSteel Bars, Carbon, Hot-Wrought or Cold-Finished,Special Quality, for Pressure Piping ComponentsA696A

8、These designations refer to the latest issue of the respective specifications, which appear either in the Annual Book ofASTM Standards, Vol 01.05, or as reprints obtainable from ASTM.1.2 In case of any conflict in requirements, the requirements of the purchase order, the individual material specific

9、ation, and thisgeneral specification shall prevail in the sequence named.1.3 The values stated in inch-pound units or SI units are to be regarded as the standard. Within the text, the SI units are shownin brackets. The values stated in each system are not exact equivalents; therefore, each system mu

10、st be used independently of theother. Combining values from the two systems may result in nonconformance with the specification.1.4 For purposes of determining conformance to this specification and the various material specifications referenced in 1.1,dimensional values shall be rounded to the neare

11、st unit in the right-hand place of figures used in expressing the limiting valuesin accordance with the rounding method of Practice E29.1 This specification is under the jurisdiction ofASTM Committee A01 on Steel, Stainless Steel and RelatedAlloys and is the direct responsibility of Subcommittee A01

12、.15on Bars.Current edition approved Nov. 1, 2015Dec. 1, 2016. Published November 2015February 2017. Originally approved in 1957. Last previous edition approved in 20122015as A29/A29M 12A29/A29M 15.1. DOI: 10.1520/A0029_A0029M-15.10.1520/A0029_A0029M-16.2 For ASME Boiler and Pressure Vessel Code appl

13、ications, see related Specification SA-29/SA-29M in Section II of that Code.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately

14、 depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.*A Summary of Changes section appears at the end of this standardCopyright ASTM Intern

15、ational, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1NOTE 1Specification A29/A29M previously listed dimensional tolerances for cold-finished bars; these are now found in Specification A108.2. Referenced Documents2.1 ASTM Standards:3A108 Specification for Steel

16、 Bar, Carbon and Alloy, Cold-FinishedA304 Specification for Carbon and Alloy Steel Bars Subject to End-Quench Hardenability RequirementsA311/A311M Specification for Cold-Drawn, Stress-Relieved Carbon Steel Bars Subject to Mechanical Property RequirementsA321 Specification for Steel Bars, Carbon, Que

17、nched and Tempered (Withdrawn 2007)4A322 Specification for Steel Bars, Alloy, Standard GradesA370 Test Methods and Definitions for Mechanical Testing of Steel ProductsA434/A434M Specification for Steel Bars, Alloy, Hot-Wrought or Cold-Finished, Quenched and TemperedA499 Specification for Steel Bars

18、and Shapes, Carbon Rolled from “T” RailsA575 Specification for Steel Bars, Carbon, Merchant Quality, M-GradesA576 Specification for Steel Bars, Carbon, Hot-Wrought, Special QualityA663/A663M Specification for Steel Bars, Carbon, Merchant Quality, Mechanical PropertiesA675/A675M Specification for Ste

19、el Bars, Carbon, Hot-Wrought, Special Quality, Mechanical PropertiesA689 Specification for Carbon and Alloy Steel Bars for SpringsA696 Specification for Steel Bars, Carbon, Hot-Wrought or Cold-Finished, Special Quality, for Pressure Piping ComponentsA700 Guide for Packaging, Marking, and Loading Met

20、hods for Steel Products for ShipmentA739 Specification for Steel Bars, Alloy, Hot-Wrought, for Elevated Temperature or Pressure-Containing Parts, or BothA751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel ProductsE29 Practice for Using Significant Digits in Test Data to Dete

21、rmine Conformance with SpecificationsE112 Test Methods for Determining Average Grain Size2.2 Federal Standards:5Fed. Std. No. 123 Marking for Shipment (Civil Agencies)Fed. Std. No. 183 Continuous Identification Marking of Iron and Steel Products2.3 Military Standard:5MIL-STD-163 Steel Mill ProductsP

22、reparation for Shipment and Storage2.4 Other Standards:6AIAG B-1 Bar Code Symbology Standard for 3-of-9 Bar CodesAIAG B-5 02.00 Primary Metals Tag Application Standard3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 cold-finished steel barssteel bars produced by cold finishing

23、previously hot-wrought bars by means of cold drawing,cold forming, turning, grinding, or polishing (singly or in combination) to yield straight lengths or coils in sections that are uniformthroughout their length and in the following sections and sizes:3.1.1.1 rounds9 in. 230 mm and under in diamete

24、r,3.1.1.2 squares6 in. 150 mm and under between parallel surfaces,3.1.1.3 hexagons4 in. 100 mm and under between parallel surfaces,3.1.1.4 flats18 in. 3 mm and over in thickness and not over 12 in. 300 mm in width, and3.1.1.5 special bar sections.3.1.2 hot-wrought steel barssteel bars produced by ho

25、t forming ingots, blooms, billets, or other semifinished forms to yieldstraight lengths (or coils, depending upon size, section, and mill equipment) in sections that are uniform throughout their length,and in the following sections and sizes:3.1.2.1 rounds732 to 10.0 in. 5.5 to 250 mm, inclusive,3.1

26、.2.2 squares732 to 6.0 in. 6 to 160 mm, inclusive,3.1.2.3 round-cornered squares732 to 8.0 in. 6 to 200 mm, inclusive,3 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. ForAnnual Book ofASTM Standardsvolume information, refer to t

27、he standards Document Summary page on the ASTM website.4 The last approved version of this historical standard is referenced on www.astm.org.5 Copies of military specifications, military standards, and federal standards required by contractors in connection with specific procurement functions should

28、 be obtainedfrom the procuring activity or as directed by the contracting officer, or from DLA Document Services, Building 4/D, 700 Robbins Ave., Philadelphia, PA 19111-5094,http:/quicksearch.dla.mil.6 Available from Automotive Industry Action Group (AIAG), 26200 Lahser Rd., Suite 200, Southfield, M

29、I 48033-7156, http:/www.aiag.org.A29/A29M 1623.1.2.4 flats14 to 8 in. inclusive, in width: 1364 in. in minimum thickness up to 6 in. in width; and 0.230 in. in minimumthickness for over 6 to 8 in. in width, inclusive over 5 mm in thickness up to 150 mm in width; and over 6 mm in thickness forover 15

30、0 mm through 200 mm in width. Maximum thickness for all widths is 4 in. 100 mm,3.1.2.5 hexagons and octagons14 to 4116 in. 6 to 103 mm, inclusive, between parallel surfaces,3.1.2.6 bar size shapesAngles, channels, tees, zees, when their greatest cross-sectional dimension is under 3 in. 75 mm, and3.1

31、.2.7 special bar sectionsHalf-rounds, ovals, half-ovals, other special bar size sections.3.1.3 lotunless otherwise specified in the contract or order, a lot shall consist of all bars submitted for inspection at the sametime of the same heat, condition, finish, size, or shape. For bars specified in t

32、he quenched and tempered condition, when heattreated in batch-type furnaces, a lot shall consist of all bars from the same heat, of the same prior condition, the same size, andsubjected to the same heat treatment in one tempering charge. For bars specified in the quenched and tempered condition, whe

33、nheat treated without interruption in a continuous-type furnace, a lot shall consist of all bars from the same heat, of the same priorcondition, of the same size, and subjected to the same heat treatment.4. Chemical Composition4.1 Limits:4.1.1 The chemical composition shall conform to the requiremen

34、ts specified in the purchase order or the individual productspecifications. For convenience the grades commonly specified for carbon steel bars are shown in Tables 1 and 2. Bars may beordered to these grade designations and when so ordered shall conform to the specified limits by heat analysis.4.1.2

35、 When compositions other than those shown in Tables 1 and 2 are required, the composition limits shall be prepared usingthe ranges and limits shown in Table 3 for carbon steel and Table 4 for alloy steel.4.2 Heat or Cast Analysis:4.2.1 The chemical composition of each heat or cast shall be determine

36、d by the manufacturer in accordance with Test Methods,Practices, and Terminology A751.4.2.2 The heat or cast analysis shall conform to the requirements specified in the product specification or purchase order. Thesecan be the heat chemical range and limit for a grade designated in Tables 1 and 2, or

37、 another range and limit in accordance with4.1.2, or with requirements of the product specification.NOTE 2Heat analysis for lead is not determinable since lead is added to the ladle stream while each ingot is poured. When specified as an addedelement to a standard steel, the percentage of lead is re

38、ported as 0.15 to 0.35 incl, which is the range commonly specified for this element.4.2.3 If requested or required, the heat analysis shall be reported to the purchaser or his representative.4.2.4 Reporting of significant figures and rounding shall be in accordance with Test Methods, Practices, and

39、Terminology A751.4.3 Product Analysis:4.3.1 Merchant quality carbon bar steel is not subject to rejection for product analysis unless misapplication of a heat is clearlyindicated.4.3.2 Analyses may be made by the purchaser from finished bars other than merchant quality representing each heat ofopen-

40、hearth, basic-oxygen, or electric-furnace steel. The chemical composition thus determined shall not vary from the limitsspecified in the applicable specification by more than the amounts prescribed in Table 5 and Table 6, but the several determinationsof any element, excluding lead, in a heat may no

41、t vary both above and below the specified range. Rimmed or capped steel ischaracterized by a lack of homogeneity in its composition, especially for the elements carbon, phosphorus, and sulfur; therefore,when rimmed or capped steel is specified or required, the limitations for these elements shall no

42、t be applicable. Because of thedegree to which phosphorus and sulfur segregate, the limitations for these elements shall not be applicable to rephosphorized orresulfurized steels.4.3.3 Samples for product analysis shall be taken by one of the following methods:4.3.3.1 Applicable to small sections wh

43、ose cross-sectional area does not exceed 0.75 in.2 500 mm2 such as rounds, squares,hexagons, and the like. Chips are taken by milling or machining the full cross section of the piece. Drilling is not a feasible methodfor sampling sizes 0.75 in.2 and smaller.4.3.3.2 Applicable to products where the w

44、idth of the cross section greatly exceeds the thickness, such as bar size shapes andlight flat bars. Chips are taken by drilling entirely through the steel at a point midway between the edge and the middle of thesection, or by milling or machining the entire cross section.4.3.3.3 Applicable to large

45、 rounds, squares semifinished, etc. Chips are taken at any point midway between the outside and thecenter of the piece by drilling parallel to the axis or by milling or machining the full cross section. In cases where these methodsare not practicable, the piece may be drilled on the side, but chips

46、are not taken until they represent the portion midway betweenthe outside and the center.4.3.3.4 When the steel is subject to tension test requirements, the tension test specimen can also be used for product analysis.In that case, chips for product analysis can be taken by drilling entirely through t

47、he tension test specimens or by the methoddescribed in 4.3.3.1.4.3.4 When chips are taken by drilling, the diameter of the drill used shall conform to the following:A29/A29M 163TABLE 1 Grade Designations and Chemical Compositions of Carbon Steel BarsGrade Designation Heat Chemical Ranges and Limits,

48、 %Carbon Manganese Phosphorus, max Sulfur, maxANonresulfurized Carbon SteelsB,C, D,E,F1005 0.06 max 0.35 max 0.040 0.0501006 0.08 max 0.250.40 0.040 0.0501008 0.10 max 0.300.50 0.040 0.0501010 0.080.13 0.300.60 0.040 0.0501011 0.080.13 0.600.90 0.040 0.0501012 0.100.15 0.300.60 0.040 0.0501013 0.110

49、.16 0.500.80 0.040 0.0501015 0.130.18 0.300.60 0.040 0.0501016 0.130.18 0.600.90 0.040 0.0501017 0.150.20 0.300.60 0.040 0.0501018 0.150.20 0.600.90 0.040 0.0501019 0.150.20 0.701.00 0.040 0.0501020 0.180.23 0.300.60 0.040 0.0501021 0.180.23 0.600.90 0.040 0.0501022 0.180.23 0.701.00 0.040 0.0501023 0.200.25 0.300.60 0.040 0.0501025 0.220.28 0.300.60 0.040 0.0501026 0.220.28 0.600.90 0.040 0.0501029 0.250.31 0.600.90 0.040 0.0501030 0.280.34 0.600.90 0.040 0.0501034 0.320.38 0.500.80