ARMY MIL-T-49381-1980 TEST SET THERMAL SIGHT TS-3681 VSG-2《TS-3681 VSG-2型热瞄准测试装置》.pdf

《ARMY MIL-T-49381-1980 TEST SET THERMAL SIGHT TS-3681 VSG-2《TS-3681 VSG-2型热瞄准测试装置》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-T-49381-1980 TEST SET THERMAL SIGHT TS-3681 VSG-2《TS-3681 VSG-2型热瞄准测试装置》.pdf（17页珍藏版）》请在麦多课文档分享上搜索。

1、sMIL-T-4938L 58 7797906 OL63b03 5 mt MIL-T-49381(ER) 2 July 1980 MILITARY SPECIFICATION TEST SET, THERMAL SIGHT, TS-3681/VSG-2 This specification is approved for use by USAERADCOM, Department of the Army, and is available for use by all Departments and Agencies of the Department of Defense. 1.1 Scop

2、e. This specification covers the Test Set, Thermal Sight, TS-36811 VSG-2. 2. APPLICABLE DOCUMENTS 2.1 Issues of documents. The following documents of the issue in effect on date of invitation for bids or request for proposal, form a part of this specification to the extent specified herein. SPECIFIC

3、ATIONS FEDERAL PPP-B- 5 6 6 PPP-B-636 PPP-B-665 PPP-B-676 MILITARY MIL-P- 116 MIL-P- 11268 MIL-E- 17 5 5 5 MIL-T-28800 - Boxes, Folding, Paperboard - Boxes, Shipping, Fiberboard - Boxes, Paperboard, Metal Edged and Components - Boxes, Setup - Preservation-Packaging, Methods of - Parts, Materials, an

4、d Processes Used in 7 Electronic and Electrical Equipment, Electronic Equipment Accessories, and Repair Parts, Packaging and Packing of Electronic Equipment, General Specification for - Test Equipment for Use With Electrical and Beneficial comments (reconmendations, additions, deletions) and any per

5、tinent data which may be of use in improving this document should be addressed to: Hq, USA Electronics Research and Development Command, ATTN: DRDEL-E, 2800 Powder Mill Road, Adelphi, MD 20783 by using the self-addressed Standard- ization Document Improvement Proposal (DD Form 1426) appearing at the

6、 end of this document or by letter. FSC 5855 THIS DOCUMENT CONTAINS ,I!, PAGES Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-49381 (ER) STANDARDS MILITARY MIL-STD-105 MIL-STD-129 MIL-STD-252 MIL-STD-454 MIL-STD-461 MIL-STD-462 MIL-STD-810 DRA

7、WINGS DLSM-B-804916 MIL-T-473L 58 rn 7777906 0363604 7 i7 w 1 - Sampling Procedures and Tables for - Marking for Shipment and Storage - Classification of Visual and Mechanical Inspection by Attributes Defects for Equipment, Electronic, Wired, and Other Devices tronic Equipment tics, Requirements for

8、 Equipment tics, Measurement of - Standard General Requirements for Elec- - Electromagnetic Interference Characteris- - Electromagnetic Interference Characteris- - Environmental Test Methods - Test Set, Sight, Thermal, Tank Mounted AN/VSG-2 (Copies of specifications, standards, drawings, and publica

9、tions required by contractors in connection with specific procurement functions should be ob- tained from the procuring activity or as directed by the contracting officer.) 3. REQUIREMENTS 3.1 Description. The Test Set, Thermal Sight, TS-3681/VSG-2, herein known as the test set, shall support mainte

10、nance of the Sight, Thermal, Tank Mounted, AN/VSG-2 equipment at the direct support and general support (DS/GS) maintenance environments. The test set shall consist of two containers. MIL-T-28800 shall be used to define the general requirements of the Collimator, Type I, class 4, style T, and type I

11、, class 4, style C for the test station. a. 58-inch collimator. Container number 1. b. Line Replaceable Unit (LRU) test station. Container number 2. 3.2 Construction. The test set shall be constructed in accordance with DLSM-B-804916 or as specified in the contract. 3.3 First article. When specified

12、 in the contract (see 6.21, the contractor shall furnish test sets for first article inspections. 3.4 Parts, materials, and processes. Parts, materials, and processes shall be as specified herein and as shown on the applicable drawings. Parts, materi- als, and processes not specified shall be select

13、ed in accordance with MIL-P- 11268. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-* * L I - MIL-T-4738L 58 3977706 0363605 7 MIL-T-49 38 1 (ER) 3.5 Components. The test set consists of two holding fixtures that will provide a stable mount for the

14、 TTS LRUs and two containers that house the following components. Container number one houses the collimator with its temperature controller, spindle and drum assembly and the input power cable. Container number two houses the LRU test station, test target reticle combiner, LED viewer telescope, PWB

15、 puller, spanner wrench, and the TTS interconnect cables. with their applicable drawings, specifications, and as specified herein. Each component of the two containers shall be constructed in accordance 3.6 Preconditioning. Each test set shall be subjected to a 48 hour precon- ditioning prior to del

16、ivery. 3.7 Operation. 3.7.1 Power. 3.7.1.1 Collimator. The collimator shall operate from a 115 Vac, 50/60 Hz single phase power source. 3.7.1.2 Test station. The LRU test station shall operate from a direct current source from a minimum of 18 volts to a maximum of 30 volts. The maxi- mum peak curren

17、t drain at any time during operation of the test station shall not exceed 25 amperes. 3.7.2 Collimator output. The collimator shall contain a temperature con- troller and spindle and drum assembly which when used will provide a combina- tion of six (6) collimated infrared and visible targets to the

18、unit under test sufficient to derive the performance status. The temperature controller and target source assembly shall create a calibrated temperature difference be- tween its blackbody source and the target array. at the resolution frequency shall be 0.45, 20.045C for the MRT taggets. the other t

19、argets, the temperature difference shall be 4.50, 20.45 C. This temperature difference For 3.7.3 Test station electrical protection. The test station shall be equipped with devices to protect the system from reverse polarity, overcur- rent, short circuit and under/over voltages, on the input power s

20、ide of the test station. These devices shall be located 3.7.4 Test station output characteristics. The test station shall have two modes of operation, STANDBY and ON. In the STANDBY mode, the test station shall provide the following outputs: a. 120, +10 Vac (under load), 400, 220 Hz, 2-phase, square

21、 wave. b. 18 to30 Vdc. c. 5.0, - +0.5 Vdc (for operation of BITE-circuitry). In the ON mode, all of the voltages listed for the STANDBY mode shall be pro- vided plus the following additional voltages: d. 18 to 30 Vdc (this in addition to the 18 to 30 Vdc in STANDBY). e. Eight regulated voltages as s

22、hown below. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-473L 5 7777706 OL63bOb O Output voltage (Vdc 1 MIL-T-49381 (ER) Maximum continuous current Minimum ripple rejection (amperes) (dB) NOTE: Input ripple voltage equals 3.0 V p-p at O to

23、 35 kHz. +10.5 20.5 +10.0 +0.5 -9.0 70.5 +1O.O 78.0 -0.5 +5.0 20.3 +15.0 70.5 -5.0 +Oe3 -15.0 50.5 1.0 1.0 1.0 2.0 0.750 O. 500 1.0 0.750 4 60 50 50 50 50 50 50 50 3.7.5 Test target/reticle combiner. The test target/reticle combiner shall combine a visible target from the collimator with the reticle

24、 image for reticle focus. It shall also divide and separate the target, providing a double image for adjusting IR magnification. 3.7.6 LED viewer telescope. The LED viewer telescope shall allow visual evaluation of the LED image from the TTS head assembly. 3.7.7 Controls. 3.7.7.1 Collimator controls

25、. 3.7.7.1.1 OFF/ON. The OFF/ON switch shall control application of power to the temperature controller and provide 3-ampere circuit breaker protection. 3.7.7.1.2 Target select. The target select control shall provide an opera- tor the option to select any one of six available targets. 3.7.7.1.3 ON/A

26、LIGN. The ON/ALIGN switch shall permit either alignment or normal operation of the temperature controller. 3.7.7.2 Test station controls. 3.7.7.2.1 Power converter simulator OFF/ON. The power converter simulator OFF/ON control shall provide the operator the capability of simulating the power convert

27、er character ist ics . 3.7.7.2.2 Power converter simulator BITE. The power converter simulator BITE control shall provide a SAFE/FAIL indication of the internal power con- verter. 3.7.7.2.3 Reticle brightness. A reticle brightness control shall vary the intensity of the reticle brightness. 4 . Provi

28、ded by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-c MIL-T-49 38 1 (ER ) 3.7.7.2.4 Commander/gunner. The commander/gunner control shall switch command functions between commanders and gunners displays. 3.7.7.2.5 Polarity. The polarity control shall allow ope

29、rator selection of either white hot or black hot video polarity. 3.7.7.2.6 System test. The system test switch shall allow the operator to exercise the BITE circuitry of the LRU under test. 3.7.7.2.7 Brightness. A brightness control shall simulate the gunners/ commanders display controls. 3.7.7.2.8

30、Contrast. A contrast control shall simulate the gunnerslcommand- ers display control. 3.7.7.2.9 Mode select. A mode-select switch shall simulate the OFF/STBY/ON switch on the gunners display. 3.7.7.2.10 Cool/warm. A coollwarm control shall simulate the cooldown circuitry in the head assembly. assemb

31、ly is under test. This control shall be disabled when a head 3.7.7.2.11 Narrowlwide field of view (FOV). A control shall simulate the selection of either NFOV or WFOV in the head assembly. i 3.7.7.2.12 Dc converter load OFF/ON. This control shall allow an operator to load the dc circuits of a power

32、converter under test to 80 percent of capacity. 3.7.7.2.13 115 Vac load OFFION. This control shall allow an operator to load the ac output of a power converter under test to 80 percent of capacity. 3.7.7.2.14 Reticle slew. This control shall slew the reticle in azimuth. 3.7.7.2.15 Function select. T

33、his control shall allow operator selection of a group of three signals. 3.7.7.2.16 Field select. This control shall allow selection of a single signal from the group of three selected by the function select switch. 3.7.8 Interconnect cables. The test station shall be equipped with seven interconnect

34、ing cables that shall provide the capability of performing all necessary tests and alignments on the TTS and shall provide for self testing of the LRU test station. 3.8 Environment. The test set shall operate without damage or degradation in performance during and after exposure and testing to the e

35、nvironmental conditions specified. Damage is defined as degradation in specified perform- ance, breakage, loosening, shift, evidence of condensation or moisture within the system, and failure to operate in accordance with the requirements of this spec if icat ion. 5 I Provided by IHSNot for ResaleNo

36、 reproduction or networking permitted without license from IHS-,-,-MIL-T-49381 (ER) 3.8.1 Altitude. The test set shall operate at altitudes up to 15,000 feet above sea level and be transportable at altitudes up to 40,000 feet above sea level without damage. 3.8.2 High temperature. O 3.8.2.1 Operatio

37、n. The test set shall operate at temperatures to +55 C. 3.8.2.2 Storage. The test set shall withstaqd storage at temperatures to +85OC. 3.8.3 Low temperature. 3.8.3.1 Operation. 3.8.3.2 Storage. The test set shall operate at temperatures to OC. The test set shall withstand storage at temperatures to

38、 -62OC. 3.8.4 percent 3.8.5 damaged 3.8.6 Humidity. The test set shall not be damaged by exposure to 95, (+5 -O re la t ive humid it y . Fungus. The test set, without its shipping container, shall not be by exposure to fungus growth. Salt fog. 3.8.6.1 Test station. The test station in its shipping c

39、ontainer shall not be damaged by exposure to a salt fog atmosphere of 5 percent NaCl atomized spray for 48 hours. 3.8.6.2 Collimator. The collimator in its enclosure shall not be damaged by exposure to a salt fog atmosphere of 20 percent NaCl atomized spray for 48 hours. 3.8.7 Watertight. The collim

40、ator, with its cover on, shall not be damaged after being submerged to a depth of 3 feet in water. 3.8.8 Shock. 3.8.8.1 Shock pulse level. The test set shall operate properly after being exposed to shock inputs up to 30 gs. 3.8.8.2 Bench handling. The test set shall not be damaged by bench handling

41、during normal maintenance activities. 3.8.8.3 Transit drop. 3.8.8.3.1 Test station. The test station shall not be damaged after being subjected to transit drops from a height of 12 inches while contained in its transit case. Provided by IHSNot for ResaleNo reproduction or networking permitted withou

42、t license from IHS-,-,-MIL-T-Ll93L 58 W 79739Ob 0363609 b W1 J ; MIL-T-49381 (ER) 3.8.8.3.2 Collimator. The collimator shall not be damaged after being subjected to transit drops from a height of 30 inches while contained in its transit case. 3.8.9 Vibration. The test set (containers with contents i

43、nstalled and covers in place) shall show no degradation in appearance or performance after being subjected to vibration inputs up to 3 gs. 3.8.10 Sand and dust resistance (collimator only). The collimator, with the cover installed and latched, shall not be damaged after being exposed to dust at velo

44、cities up to 1750 feet per minute for periods up to 12 hours. 3.9 Treatment and painting. Unless otherwise specified, the test set and its components and parts shall be cleaned, treated, and painted in accordance with the applicable drawing. 3.10 Nameplates and product marking. Unless otherwise spec

45、ified, the test set, parts, components, subassemblies, and assemblies thereof shall be marked for identification and reference designation markings in accordance with the applicable drawing. 3.11 Workmanship. Workmanship shall be as specified in MIL-STD-454, Requirement 9. 4. QUALITI ASSURANCE PROVI

46、SIONS 4.1 Responsibility for inspection. Unless otherwise specified in the con- ( tract, the contractor is responsible for the performance of all inspection requirements as specified herein. tract, the contractor may use his own or any other facilities suitable for the performance of the inspection

47、requirements specified herein, unless disapproved by the Government. inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. Except as otherwise specified in the con- The Government reserves the right

48、to perform any of the 4.2 Classification of inspections. Inspections shall be classified as follows : a. b . c. First article inspection (see 4.3). Quality conformance inspect ion (see 4.5). Inspection of packaging (see 4.9). 4.3 First article inspection. Unless otherwise specified in the contract o

49、r purchase order, first article inspection shall be performed by the con- trac tor, 7 . o Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-T-9933 5 9997906 0363630 2 M - E- r 3- MIL-T-49381 (ER) 4.3.1 Inspections. Each assembled first article test set shall be examined in accordance with table I. All materials, parts, processes, and assemblies shall be examined for confor