ARMY MIL-PRF-62368 C-2009 MOTOR GEARHEAD 18 - 30 VOLTS DIRECT CURRENT《18-30伏直流减速发动机》.pdf
《ARMY MIL-PRF-62368 C-2009 MOTOR GEARHEAD 18 - 30 VOLTS DIRECT CURRENT《18-30伏直流减速发动机》.pdf》由会员分享,可在线阅读,更多相关《ARMY MIL-PRF-62368 C-2009 MOTOR GEARHEAD 18 - 30 VOLTS DIRECT CURRENT《18-30伏直流减速发动机》.pdf(24页珍藏版)》请在麦多课文档分享上搜索。
1、 INCH-POUND MIL-PRF-62368C(AT) 28 May 2009 SUPERSEDING MIL-PRF-62368B(AT) 8 July 1997 PERFORMANCE SPECIFICATION MOTOR, GEARHEAD, 18 - 30 VOLTS, DIRECT CURRENT This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification c
2、overs a direct current gearhead motor used to operate the Remote Arming Device (RAD) on a military ground vehicle. 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3, 4, or 5 of this specification. This section does not include documents cited in ot
3、her sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3, 4, or 5 of this specifi
4、cation, whether or not they are listed. Comments, suggestions, or questions on this document should be addressed to U.S. Army Tank-automotive and Armaments Command, ATTN: AMSRD-TAR-E/CM/DM/STND MS#268, 6501 E. 11 Mile Road, Warren, MI 48397-5000 or emailed to DAMI_STANDARDIZATIONconus.army.mil. Sinc
5、e contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at http:/assist.daps.dla.mil. AMSC N/A FSC 6105 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. 2.2 Government documents. 2.2.1 Specifi
6、cations, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract (see 6.2). Provided by IHSNot for ResaleNo
7、reproduction or networking permitted without license from IHS-,-,-MIL-PRF-62368C(AT) INTERNATIONAL STANDARDIZATION AGREEMENTS STANAG 1135 - Interchangeability of Fuels, Lubricants and Associated Products used by the Armed Forces of the North Atlantic Treaty Nations DEPARTMENT OF DEFENSE STANDARDS MI
8、L-STD-461 - Requirements for the Control of Electromagnetic Interference Characteristics of Subsystems and Equipment MIL-STD-810 - Environmental Engineering Considerations and Laboratory Tests DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-454 - General Guidelines for Electronic Equipment (Copies of these
9、 documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2.2 Other Government documents, drawings, and publications. The following other Government documents, drawings,
10、and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. US ARMY TACOM DRAWINGS 12265908 - Motor, Gearhead (Interface) (Copies of this drawing are available from the U.S. A
11、rmy Tank-automotive and Armaments Command, ATTN: AMSRD-TAR-E/CM/DM/STND MS #268, 6501 E. 11 Mile Road, Warren, MI 48397-5000, or email DAMI_STANDARDIZATIONconus.army.mil.) 2.3 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless oth
12、erwise specified, the issues of these documents are those cited in the solicitation or contract (see 6.2). AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI) ANSI/ASQC Z1.4 - Sampling Procedures and Tables for Inspection by Attributes (DoD Adopted) ANSI/SAE AS1933 - Age Controls for Hose Containing Age-Se
13、nsitive Elastomeric Material (DoD Adopted) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-62368C(AT) ANSI/SAE AS478 - Identification Marking Methods (DoD Adopted) (Copies of these documents are available online at www.ansi.org or from ANSI
14、 Customer Service Department, 25 W. 43rd Street, 4th Floor, New York, NY 10036.) ASTM INTERNATIONAL ASTM B633 - Standard Specification for Electrodeposited Coatings of Zinc on Iron or Steel (DoD Adopted) (Copies of these documents are available from www.astm.org or ASTM International, 100 Barr Harbo
15、r Drive, West Conshohocken, PA 19428-2959.) 2.4 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersed
16、es applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First article. When specified (see 6.2), a sample shall be subjected to first article inspection in accordance with 4.3. 3.2 Materials. Materials used shall be in accordance with the manufacturers m
17、aterials specifications for gearhead motors. The materials shall be capable of meeting all the operational and environmental requirements specified herein (see 4.5.1). 3.2.1 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials sho
18、uld be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs (see 4.5.1). 3.2.2 Age sensitive materials. The use of age-sensitive elastomers, as defined by ANSI/SAE AS1933,
19、 shall be identified and controlled in accordance with that standard (see 4.5.1). 3.2.3 Gearing. All gearing shall be of the necessary materials, finishes, and precision to provide reliable performance as outlined herein (see 4.5.1). 3.2.4 Lubrication. The unit shall be lubricated with grease confor
20、ming to STANAG 1135, method G-354 or equivalent and shall not require lubrication during the service of the assembly (see 4.5.1 and 6.4). 3 3.2.5 Cover and mounting flange. Material shall be suitable for the intended purpose. Non-corrosion metal resistant materials shall be zinc plated in accordance
21、 with ASTM B633, service condition (SC 8) (minimum), type II or equivalent (see 4.5.1). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-62368C(AT) 3.2.6 Dissimilar metals. Unless suitably protected against electrolytic corrosion, dissimilar m
22、etals shall not be placed in direct contact. When protection is used, it shall be such type that a low impedance path is offered to radio frequency currents (see 4.5.1). 3.3 Construction. The motor and the output shaft shall conform to the envelope dimensions and interfaces of Drawing 12265908 (see
23、4.5.1 and 4.5.2). 3.3.1 Backlash. Backlash shall be not more than 3 degrees () (see 4.5.1). 3.3.2 Bearings. Bearings shall be suitable for their intended purpose. Bearings which are exposed to the environment shall be of the sealed type (see 4.5.1). 3.3.3 Moisture pockets. Pockets, wells, and traps
24、in which water or condensed water vapor can collect shall be avoided. Lead wire entry shall be sealed to prevent entrance of contamination into the motor (see 4.5.1). 3.3.4 Standard parts. Standard utility parts, such as screws, bolts, nuts, cotter pins, etc., shall be selected in accordance with th
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ARMYMILPRF62368C2009MOTORGEARHEAD1830VOLTSDIRECTCURRENT1830 直流 减速 发动机 PDF

链接地址:http://www.mydoc123.com/p-447565.html