ARMY MIL-G-60087 F-1987 GRENADE HAND RIOT CS M7A3《M7A3 CS防暴动手榴弹》.pdf

《ARMY MIL-G-60087 F-1987 GRENADE HAND RIOT CS M7A3《M7A3 CS防暴动手榴弹》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-G-60087 F-1987 GRENADE HAND RIOT CS M7A3《M7A3 CS防暴动手榴弹》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、NIL-G-bO087F 13 77777Ob 0335422 7 = 5-37-09 MIL-G-60087F( EA) 6 March 1987 SUPERSEDING MIL-G-6008 7E ( MU) 23 July 1971 MILITARY SPECIFICATION GRENADE, HAND, RIOT, CS, M7A3 This specification is approved for use by U.S. Army Chemical Research, Development and Engineering Center, Department of the Ar

2、my, and is available for use by ail Departments and Agencies of the Department of Defense. 1. SCOPE . 1 1.1 Scope. This specification covers one type of hand grenade. 20 APPLICABLE DOCUMENTS 2 . 1 Government documents. 2.1.1 Specifications and standards. The following specifications and stan- dards

3、form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of these documents shall be those listed in that issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation. SPECIFICATION

4、S FEDERAL QQ-S-781 - Strapping, Steel, and Seals. TT-W-572 - Wood-Preservative, Water-Repellent. PPP-3-621 - Boxes, Wood, Nailed and Lock Corner. PPP-F-320 - Fiberboard; Corrugated and Solid , Sheet Stock (Container Grade) , and Cut Shapes. : Beneficial comments (recommendations, additions, deletion

5、s) and any perti- : : nent data which may be of use in improving this document should be addressed: : to: Commander, U.S. Army Chemical Research, Development and Engineering : : Center, ATTN: SMCCR-SPT-S, Aberdeen Proving Ground, MD 21010-5423 by using: : the self-addressed Standardization Document

6、Improvement Proposal (DD Form : : 1426) appearing at the end of this .document or by letter. FSC 1330 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. 1 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-G-60087F 13

7、777790b 0335423 q MIL-G-60087F( EA) MILITARY MIL-B-2427 - Boxes, Ammunition Packing: Wood , Nailed. MIL-B-46506 - Box Ammunition Packing, Wood, Wirebound. MIL-C-51029 - Chemical Agent, CS. STANDARDS MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by MIL-STD-414 - Sampling Proced

8、ures and Tables for Inspection by MIL-STD-1168 - Lot Numbering of k,mnition . Attribut es . Variables for Percent Defectives. 2.1.2 Other Government documents, drawings, and publications. The following other Government documents, drawfngs, and publications form a part of this specificaton to the ext

9、ent specified herein. Unless otherwise specified, the issues shall be those in effect on the date of the solicitation. DRAWINGS AND TECHNICAL DATA PACmGE LIST (TDPL) U.S. ARMY ARMAMENT, MUNITIONS AND CHEMICAL COMMAND CHEMICAL RESEARCK, DEVELOPMENT AND ENGINEERING CENTER TDPL 13-22-35 - Grenade, Hand

10、, Riot, CS, M7A3. PE5LICATIONC EDGENOOD ARSENAL PURCHASE DESCRIPTION 197-54-921. - Pellets, CS, Sugar Coated, (Copies of specifications, standards, and drawings required by contractors in connection with specific acquisition functions should be obtained from the con- tracting activity or as directed

11、 by the contracting activity.) 2.2 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein (except for associated detail specifications, specification sheets or MS standards), the text of this specification shall take precedence. shall s

12、upersede applicable laws and regulations unless a specific exemption has been obtained. Nothing in this specification, however, 2 t 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-G-60087F 13 m 9779906 0335424 O m MIL-F- 6008 7F ( EA) 3 REQUIRE

13、MENTS 3.1 Materials and components. 3.1.1 Materials. All materials cited on TDPL 13-22-35 or on the subsidiary drawings shall conform to the specifications lsited thereon, or to the specific characteristics set forth on the drawings. 3.1.2 Components. All components of the grenade shall conform to t

14、he speci- fications and drawings listed on TDPL 13-22-35 and subsidiary drawings. 3.2 Filling and assembly. The grenade body shall be filled with il5 + 5 grams of CS pellets and i85 + 5 grams of fuel mixture VI. be evenly dispersed in the fuel mixture before consolidation. of fill shall be consolida

15、ted in the body at the dead load of 9000 to 10,000 pounds; four increments of fill shall be used. and fuel mixture shall be introduced in such a manner as to provide a rela- tively smooth surface after consolidation. The diameter of the center hole shall not be less than 3/16 inch diameter after app

16、lication of the starter mix. The grenade shall be assembled as shown on Drawing 13-22-35. The CS pellets shall Each inerement The last increment of pellets 3.3 Functioning. The grenade shall function as follows when tested in accordance with 4.4 . 4 . 1 : (a) Emit a cloud of smoke under pressure wit

17、hout interruption for no less than i5 seconds and no more than 35 seconds. (b) Move no more than 25 feet in any one direction from the original position when it is functioned on hard packed earth free from vegetation. (c) Not flame at both ends for more than 20 percent of the total burn- ing time no

18、r at one end for 30 percent of the total burning time. (d) The time from release of the fuze striker until emission of smoke under pressure shall not exceed 7 seconds (delay time) . separation of grenade seams, top, side or bottom during functioning. There shall be no 3.4 Preproduction. Prior to the

19、 start of regular production, a preproduc- tion lot of grenades shall be produced in accordance with this specification for examination and tests. 3.5 Workmanship. The grenade shall be free from contamination (foreign matter, oil and grease) and damage such as dents, cracks or deformation which coul

20、d impair its use. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the con- tract or purchase order, the contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified 3 Provided by IHSNo

21、t for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-G-60087F 13 7797706 0335i.125 2 MIL-G-60087F ( EA) in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements speci- fied h

22、erein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. 4.1.1 Responsibility for compliance. Al1 ite

23、ms must meet all requirements of sections 3 and 5. The inspection set forth in this specification shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the specification shall not relieve the contractor of the responsibilit

24、y of assuring that all products or supplies submitted to the Government for acceptance comply with all require- ments of the contract. Sampling in quality conformance does not authorize sub- mission of known defective material, either indicated or actual, nor does it commit the Government to accepta

25、nce of defective material. 4.2 Classification of inspections, The inspection requirements specified herein are classified as follows: ( a) (b) Preproduction inspect ion ( see 4-3) . Quality conformance inspection (see 4.4). 4.3 Preproduction inspection. 4.3.1 - Lot. Prior to the start of regular pro

26、duction, a preproduction lot of 1201 grenades or production from one shift, whichever is greater, shall be pro- duced using the same methods, materials, equipment and processes as will be used during regular production, 4.3.2 Sampling. 4.3.2,l For examination. Sampling shall be conducted in accordan

27、ce with MIL-STD-105. 4.3.2.2 For destructive tests. Sampling for burning time shall be conducted in accordance with MIL-STD-414 , level II (example B-3) . excessive movement, delay, intermittent smoke, seam separation and flamers shall be equivalent to that segment of the sample from MIL-STD-414 as

28、specified in MIL-STD-105, level S-4. The sample for duds , 4.3.3 Inspection procedure. 4.3.3.1 For examination. Sample grenades shall be examined in accordance with the classification of defects and with MIL-STD-105. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without lice

29、nse from IHS-,-,-MIL-G-60087F 13 7777906 0335426 4 MIL-G-60087F ( EA) 4.3.3.2 For destructive tests. Sample grenades shall be tested in accor- dance with 4.4.4 and table I. first grenade in the sample consecutively through the entire sample. Evalua- tion for the remaining attributes in table I shall

30、 be made during the evalua- tion for burning time, except that the sample size shall be that specified in Evaluation for burning time shall begin with the MIL-STD-105 Table I. Acceptance/rejection criteria Attribut es : AQL percent defective : 3 : Duds (see 6.3) 2.5 : Movement excessive : Delay : In

31、termittent smoke 2.5 : Seam separation (ends and side) : : Flamer : Burning time 1.0 : Fuze failure (see 6.4) 4.4 Quality conformance inspection. a 4.4.1 Lotting. Alot shall be identified and controlled in accordance with MIL-STD-l-ontained in any one interfix number of grenades, no more than one in

32、terfix number from one manufacturer of the following components is per- mitt ed. (a) Pyrotechnic and starter mix. (b) Fuzes. 4 . 4 . 2 4.4.2.1 For examination. Sampling shall be conducted in accordance with Sampling . MIL-STD-105. 4.4.2.2 For destructive tests. Sampling shall be conducted in accorda

33、nce with MIL-STD-105, level S-4, for duds, excessive movement, delay, intermittent smoke, seam separation, and flamers. equivalent to that segment of the sample from MIL-STD-105, as specified in MIL- STD-414 , level I (example B-3) - The sample for burning time shall be 5 Provided by IHSNot for Resa

34、leNo reproduction or networking permitted without license from IHS-,-,-_I flIL-G-bO087F 13 U 7777706 0335427 b MIL-G-60087F( EA) 4.4.3 Inspection procedures. 4.4.3.1 For examination. Sample grenades and the level A preparation for delivery shall be examined in accordance with the classification of d

35、efects ( 4 . 4.3 . 4) and MIL-STD-105 . 4.4.3.2 For destructive test. Sample grenades shall be tested in accordance with 4.4.4 and table I. Evaluation for burning time shall begin with the first grenade in the sample consecutively through that quantity specified in MIL-STD- 414, level I. butes in ta

36、ble I. The entire sample shall be evaluated for the remaining attri- 4.4.3.3 Critical defects. Each grenade in the lot shall be inspected for its critical characteritic listed in the classification of defects. 4.4.3.4 Classification of defects. (a) Grenade, hand, riot, CS, M7A3, assembly (Drawing 13

37、-22-35 ) . Categories Defects Critical : 1 Safety pin incorrectly formed MaJor: AQL 1.0 percent defective 101 Component missing 102 Component incorrectly assembled 103 Fuze torque incorrect i04 Marking incorrect i05 Filling weight incorrect 106 107 Workmanship (3.6) Tape loose or does not cover hole

38、 Minor: AQL 2.5 percent defective 201 Protective finish missing 202 Marking missing or illegible (b) Preparation for delivery (section 5). Cat egories Defects Critical : None defined Major: AQL 2.5 percent defective 101 Container closure incorrect 102 Loose pack 6 Provided by IHSNot for ResaleNo rep

39、roduction or networking permitted without license from IHS-,-,-MIL-G-60087F( EA) Cat egories Defects Critical : None defined Major: AQL 2.5 percent defective t -. 103 104 105 i06 107 i08 109 110 Neck tube missing Instruction card missing or not Strapping missing or loose Marking missing or illegible

40、 Marking incorrect Spacer missing Collar missing or incorrect Container incorrect coated 4.4.4 Tests. Tests shall be conducted as follows: Submerge the grenade in water, having a temperature of O“ to 10F above the temperature of the grenade, to a depth of 1 to 2 inches for 35 + 5 minutes. within 1 h

41、our after removal from water. Test as specified in 4.4.4.1 4.4.4.1 Functioning. Pull out the safety pin and throw the grenade downwind on the ground or into a suitable enclosure (see 6.3). 4.4.4.2 Fuze failure. Grenade failure solely due to malfunctioning of the fuze shall be refuzed in order to com

42、plete the quantity of data required for evaluation of the lag time and burning time performance (see 6.4). 5. PACKAGING 5.1 Packing, level A. Grenades shall be individually packaged as shown in Drawing 13-9-120. 5.2 Packing, level A. Sixteen grenades, unit packed as specified in 5.1 shall be packed

43、together, fuze end up, in one layer, in an overseas-type or class wood shipping container conforming to PPP-B-621, class 2, style 4, type 2, grade A. Fiberboard pads, conforming to type CF, grade WC, variety SW of PPP-F-320, shall completely separate the contents fromthe shipping con- tainer. Additi

44、onal pads, as required shall be used to insure a tight pack. Inside dimensions of the wood shipping container shall be 11-5/8 by ii/-5/8 by 6-5/8 inches (length, width and depth, respectively) . forming to Drawing 13-19-38 shall be placed inside the shipping container on top of the grenades. The shi

45、pping container shall be closed and strapped in accordance with PPP-B-621 and its appendix, using galvanized, flat steel strappng conforming to class B, type I of QQ-S-781. An instruction card con- 5.3 Palletization. Palletize in accordance with applicable 19-48 series drawings . 7 Provided by IHSNo

46、t for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-G-60087F( EA) 5.4 Marking. In addition to any special marking required by the contract or Ship- Suffi- order, uiit packages shall be marked in accordance with Drawing 13-9-105. ping containers shall be marked in acc

47、ordance with Drawing 13-22-46. cient drying time shall be allowed after application of the wood preservative to insure that all markings shall be clear, legible and permanent. 6. NOTES 6.1 Ordering data. Acquisition documents should specify the following: (a) (b) Preproduction: Title, number, and da

48、te of this specification. (1) (2) (3) Time allowed for contractor submission of samples for Govern- Name and address of test facility and shipping instructions Time required for the Government to notify the contractor ment test and evaluation after award of contract. when testing is performed by the

49、 Government. whether or not to proceed with production. 6.2 Precautions. Because of the hazards attending the filling of munitions with chemical agents, suppliers are advised to take all precautions to protect personnel from injury while filling and assembling grenades. 6.3 Duds. A dud is defined as a malfunction due to a Mechanical or pyro- - technic failure. 6.4 Fuze failure. The result of failure of any part of the fuze expl