ARMY MIL-C-71165 (1)-1996 CONTAINER AMMUNITION LIGHTWEIGHT METAL FOR TOW 2A GUIDED MISSILE SURFACE ATTACK BGM - 71E - 5B WEAPON SYSTEM《第2A引导导弹的轻金属丝束弹药集装箱 表面袭击 BGM - 71E - 5B武器系统》.pdf

《ARMY MIL-C-71165 (1)-1996 CONTAINER AMMUNITION LIGHTWEIGHT METAL FOR TOW 2A GUIDED MISSILE SURFACE ATTACK BGM - 71E - 5B WEAPON SYSTEM《第2A引导导弹的轻金属丝束弹药集装箱 表面袭击 BGM - 71E - 5B武器系统》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-C-71165 (1)-1996 CONTAINER AMMUNITION LIGHTWEIGHT METAL FOR TOW 2A GUIDED MISSILE SURFACE ATTACK BGM - 71E - 5B WEAPON SYSTEM《第2A引导导弹的轻金属丝束弹药集装箱 表面袭击 BGM - 71E - 5B武器系统》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、= 99999Ob 2024902 700 = JINCH-POUND 1 MIL-C-71165 (AR) AMENDMENT 1 23 October 1996 MILITARY SPECIFICATION CONTAINER, AMMUNITION, LIGHTWEIGHT METAL FOR TOW 2A GUIDED MISSILE, SURFACE ATTACK: BGM - 71E - 5B WEAPON SYSTEM This amendment forms a part of Military Specification MIL-C- 71165 (AR) , dated 1

2、5 June 1993 and is approved for use by the U.S. Army Armament Research, Development and Engineering Center (ARDEC), and is available for use by all Departments and Agencies of the Department of Defense. Page 4 3.6.1 Delete paragraph in its entirety and substitute with the following new paragraph: “3

3、.6.1 Air pressure of unpainted cover assembly The unpainted cover assembly shall withstand an internal air pressure of three psi for five (5) seconds minimum. Bubbles, other than surface bubble shall cause rejection.“ 3.6.2 Delete paragraph in its entirety and substitute with the following new parag

4、raph: “3.6.2 Air pressure of unpainted body assembly The unpainted body assembly shall withstand an internal air pressme of three psi for five (5) seconds minimum. Bubbles, other than surface bubble shall cause rejection.“ AMSC N/A 1 of 4 FSC 8140 T A, Approved for public release; distribution is un

5、limited Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-flIL-C-711b5 (1) 99999Ob 2024903 647 = MIL-C-71165 (AR) AMENDMENT 1 PAGE 7 TABLE I - First artisle inspection Assemblies and components, change paragraph as follows: - . “EXAMINATION OR TEST CON

6、FORMANCE REQUIREMENT _. CRITERIA PARAGRAPH Container assemblies, painted (Dwg. 12953476 as applicable) Examination for defects 5 3.2 Air pressure 10 3.6 Painted surface - i/ 3 3.4“ Page 11 4.4.2.1 Spring Clip, Hairpin, delete Major 102 “Radius of bend“ and Major 103 “Length from end to lower edge of

7、 bend“ in their entireties and change paragraph as follows: I “Mai or 101 Diameter of coil Level III 3.2 Gage 104 Diameter of spring wire Level VI 3.2 Gage“ PAGE 12 4.4.2.2 Support, Shaft, change paragraph as follows: “Ma or 106 Material thickness Level VI 3.8 Gage“ Delete Major 104 “True position o

8、f holes located on side (used for assembly of spring and clamp)“ in its entirety PAGE 13 e, 4.4.2.3 Handle, Square, change paragraph as follows: “Ma or 105 Material thickness Level V 3.8. Vi sua 1 . Delete Major 103 “Width of spring slot“ and Major 104 Length of spring slot (DIM B)“ in their entiret

9、y. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I MILC-71165 (AR) AMENDMENT 1 PAGE 17 4.4.2.7 cover, change paragraph as follows: “Ma or 106 Material thickness Level VI 3.2 Visual“ PAGE 20 4.4.2.10 cover Assembly, Prior to painting, change as foll

10、ows : Delete Major 102 “Component missing or inadequately assembled“ In its entirety. PAGE 21 4.4.2.11 cover Assembly, Painted, add Major 102 as follows: “Ma or 102 Component missing or inadequately assembled Level III 3.2 Visual“ PAGE 24 4.4.2.14 body, delete Major 102 “Inside diameter, min. i/“ -

11、and change paragraph as follows: “Major 104 Material thickness Level VI 3.2 Gage“ Add Note i/ as follows: Major 103 can be checked on body weldment Dwg. 12944493 Page 26 4.4.2.16 body Assembly (Weldment), change paragraph as follows : “Ma or 104 Inside diameter of body after painting, min. Level VI

12、3.2 Gage“ 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MW-71165 (AR) AMENDMENT 1 Page 28 Delete paragraph 4.4.3.2 in its entirety and replace with the following: “4.4.3.2 Weld strength of rim to body (see Dwg. 12944480),Major defect. During the

13、first half of a production shift and during the last half of a production shift, a body assembly shall be randomly selected for this test. If any body assembly fails to meet the requirement when tested in accordance with 4.5.2, the quantity of body assemblies which were welded during this shift betw

14、een this weld strength test and the earlier weld strength test and (if applicable) shall be rejected.“ Page 29 Delete paragraph 4.5.2 in its entirety and replace with the following: “4.5.2 Weld strength of rim to body. The strength of the weld shall be determined through a longitudinal force test per Dwg. 12944493. Custodian: Army-AR Preparing activity: Army-AR (Project 8140 - 0170) 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-