ARMY MIL-C-44217 A-1989 CAP WATER CANTEEN 5-QUART COLLAPSIBLE《5夸特可折叠水箱罩》.pdf

《ARMY MIL-C-44217 A-1989 CAP WATER CANTEEN 5-QUART COLLAPSIBLE《5夸特可折叠水箱罩》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-C-44217 A-1989 CAP WATER CANTEEN 5-QUART COLLAPSIBLE《5夸特可折叠水箱罩》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-C-44217A 84 m 7777706 0401436 7 m I INCH-POUND 1 MIL-C-44217A 15 November 1989 SUPERSEDING MIL-C-442 17 (GL) 28 January 1986 MILITARY SPECIFICATION CAP, WATER CANTEEN, 5-QUART, COLLAPSIBLE -.- This specification is approved for use by all Departments and Agencies of the Department of Defense. 1.

2、 SCOPE 1.1 Scope. This specification covers one type and size of canteen cap. 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to-the extent specified herein-. Unless

3、otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). Beneficial comments (recommendations, additions, deletions) and any pertinent data

4、 which may be of use in improving this document should be addressed to: U.S. Army Natick Research, Development, and Engineering Center, Natick, MA 01760-5014 by using the self-addressed Standardization Document Improvement Proposal .(DD Form 1426) appearing at the end of this document or by letter.

5、I I AMSC NIA FSC 8465 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. THIS DOCUMENT CONTAINS /A PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-LILI217A BLI 7797706 0401LI37 O SPECIFICATIONS FEDERAL RR-C

6、-271 - PPP-B-56 6 - PPP-B-63 6 PPP-B-676 - - MILITARY MIL-M- 14 - MIL-R-3065 - MIL-C-5040 - MIL-L-35078 - STAN DARDS MILITARY ,MIL-STD-105 - MIL-STD-129 - MIL-STD-130 - MIL-STD-147 - MIL-STD-417 - MIL-C-44217A Chains and Attachements, Welded and Weldless Boxes, Folding, Paperboard Boxes, Shipping, F

7、iberboard Boxes, Setup Molding Plastics and Molded Plastic Parts, Thermo- Rubber, Fabricated Products Cord, Nylon Loads, Unit: Preparation of Semiperishable setting Subsistence Items; Clothing, Personal Equipment and Equipage; General Specification For Sampling Procedures and Tables for Inspection M

8、arking for Shipment and Storage Identification Marking of U.S. Military Property Palletized Unit Loads Classification System and Tests for Solid by Attributes Elastomeric Materials (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from

9、 the Naval Publications and Forms Center, (ATTN: NPODS), 5801 Tabor Avenue, Philadelphia, PA 19120-5099.) 2.1-2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. th

10、e issues are those cited in the solicitation. Unless otherwise specified, DRAWINGS U. S. ARMY NATICR RESEARCH, DEVELOPMENT, AND ENGINEERING CENTER 2-9-73 - Cap Water Canteen, Chain and Gasket, Assembled 2-9 -74 - Cap Water Canteen, Chain and Gasket Assembled; Testing Block (Copies of drawings are av

11、ailable from the U.S. Army Natick Research, Development, and Engineering Center, ATTN: STRNC-EMSS, Natick, MA 01760-5014.) !#. I. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-44217A * 2.2 Non-Government publications. The following document

12、s form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DOD adopted are those listed in the issue of the DODISS cited in the solicitation, Unless otherwise specified, the issues of documents not listed in the DODLSS are the iss

13、ues of the documents cited in the solicitation (see 6.2). U.S. DEPARTMENT OF HEALTH AND HUMAN SERVICES - 4: - E- -%;. ;. Federal Food, Drug, and Cosmetic Act and Regulations Promulgated Thereunder (21 CFR Parts 177 and 182) . (The Code of Federal Regulations (CFR) and the Federal Register (FR) are f

14、or sale on a subscription basis by the Superintendent of Documents, US Government Printing Office, Washington, DC 20402. When indicated, reprints of certain regulations may be obtained from the Federal agency responsible for issuance thereof ) AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) D 3951

15、 - Standard Practice for Commercial Packaging (Application for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103-1187.) (Non-Government standards and other publications are normally available from organizations that prepare oc dist

16、ribute the documents. These documents also may be available in or through libraries or other informational services.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this doc

17、ument, however, supersedes applicable laws and regulations unless a specific exemption has been obtained, 3 ,. . REQUIREMENTS 3.1 First article. When specified (see 6.2), a sample shall be subjected to first article inspection (see 6.31, in accordance with 4.3. 3.2 Samples. Samples, when furnished,

18、are solely for guidance and information to he contractor (see 6.4). may appear in the sample, in which case this specification shall govern. Variation from this specification 3.3 Materials. Materials specified shall conform to applicable documents and requirements specified herein. Where materials a

19、re not-definitely specified, the materials shall be of the quality normally used in comercial 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- - MIL-C-44217A 84 9999906 0401439 4 MIL-C-442 1 7A practice. It is encouraged that recycled material be u

20、sed when practical as long as it meets the requirements of this specification. 33.1 Molding, plastic. The molding plastic shall conform to type CFI-10 of MIL-M-14, shall be black in color, and shall meet the toxicity requirements of 3.5.5. 3.3.2 Cord, nylon. The nylon cord shall be type 1 or lA, OD-

21、7 conforming to MIL-C-5040. 3.4 Construction. The assembled water canteen cap and chain shall be constructed as shown on Drawing 2-9-73 and as specified herein. 3.5 Details of components. 3.5.1 Cap. The body of the cap shall be molded of plastic specified in 3.3.1 and shall show no evidence of.unsat

22、isfactory molding such as chalking, bli-stering, or distortion. When tested as specified in 4.4.5, the cap shall not crack, split, break, or sustain thread damage or other impairment. When tested as specified in 4.4.2, the water absorption shall not be greater than 4.0 percent by weight and the swel

23、ling shall not be more than 1.75 percent in any one direction. 3.5.2 Gasket. The gasket shall conform to type, class, grade and suffix letters RN420A.or RS420A1 of MIL-R-3065 and MIL-STD-417, and shall meet the toxicity requirements of 3.5.5, The thickness and diameter shall be as specified on Drawi

24、ng 2-9-73. cap and shall show no sign of looseness or turning. The gasket shall be a tight pressed fit into the 3.5.3 Chain. The chain shall conform to type II, class 6, Trade No. O of RR-2 7 1 . 3.5.4 Rivet. The rivet shall be formed from Steel Series 300 corrosion- resistant steel and shall be fir

25、mly set into the cap. When tested as specified in 4.4.5, the rivet shall remain firmly set. 3.5.5 Toxicity. The canteen cap and gasket shall conform in every respect to the provisions of the Federal Food, Drug and Cosmetic Act, Food Additive Amendment, 21 CFR Part 177 (except Sections 177.1020, 177.

26、1030, 177.1040, 177.1050 and 177.1480) and/or 177.2600 (e). 3.6 Finish. 3.6.1 Cap. The eniire surface of the top of the cap, extending down as far as the serrations, shall have a lusterless matte finish, and the other . surfaces shall have a natural finish. The matte finish and the natural finish sh

27、all be the result of the molding procedure. 4 ._. . . . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-44217A 84 m 777770b 0401440 O m MIL-C-442 17A 3.6.2 Chain and rivet. The chain and rivet shall be given a lusterless black oxidized coating.

28、 3.7 Marking for identification. The canteen cap shall be permanently and distinctly marked on the outside top surface during the molding process, with the letters “U.S.,“ the manufacturers identification mark, and the year of manufacture in accordance with MIL-STD-130. 3.8 Workmanship. The cap shal

29、l conform to the quality of product established by this specification. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements (examinations and t

30、ests) as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to

31、perform any of the inspections set forth in this specification where such inspections are deemed necessary to ensure supplies and services conform to prescribed requirements. 4.1.1 Responsibility for compliance. All items shall meet all requirements of sections 3 and 5. The inspection set forth in t

32、his specification shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the specification shall not relieve the contractor of the responsibility of ensuring that all products or supplies submitted to the Government for acce

33、ptance comply with all requirements of the contract. Sampling inspection, as part of manufacturing operations, is an acceptable practice to ascertain conformance to requirements, however, this does not authorize submission of known defective material, either indicated or actual, nor does it commit t

34、he Government to accept defective material. 4.1.2 Responsibility for dimensional requirements. Unless otherwise specified in the contract or purchase order, the contractor is responsible for ensuring that all specified dimensions have been met. When dimensions cannot be examined on the end item, ins

35、pection shall be made at any point, or at all points in the manufacturing process necessary to ensure compliance with all dimensional requirements. 4.1.3 Certificates of compliance. When certificates of compliance are submitted, the Government reserves the right to inspect such items to determine th

36、e validity of the certification. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-C-44217A 84 m 9779906 OLIO1441 2 m MIL-C-44217A 4.2 Classification of inspections. The inspection requirements specified herein are classified as follows: a. First

37、 article inspection (see 4.3) b. Quality conformance inspection (see 4.4) 4.3 First article inspection. When a first article is required (see 3.1 and 6.2), it shall be examined for the defects specified in 4.4.3 and 4.4.4 and tested for the characteristics specified in 4.4.5. 4.4 Quality conformance

38、 inspection. Unless otherwise specified, sampling for inspection shall be performed in accordance with MIL-STD-105. 4.4.1 Component and material inspection. In accordance with 4.1, components and materials shall be inspected in accordance with all the requirements of referenced documents unless othe

39、rwise excluded, amended, modified or qualified in this specification or applicable purchase document, 4.4.1.1 Component and material certification. A certificate of compliance may be acceptable as evidence that the identity, color, and toxicity of the cap conforms to the requirements specified in 3.

40、3.1 and 3.5.2. 4.4.2 In-process testing. The caps, prior to attachment of the gaskets, rivets, and chains, shall be tested for the characteristics shown in table I. The lot size shall be expressed in units of caps. The sample unit shall be one cap. The inspection-level shall be S-1 (see 6.5). TABLE

41、I. In-process test Requirement Test Characteristic paragraph procedure Water absorption 3.5.1 4.5.2 4.4.3 End item visual examination. The end items shall be examined for the defects li.sted in table II. The lot size shall be expressed in units of caps. The sample unit shall be one cap. The inspecti

42、on level shall be S-2 (see 6.5). 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-44217A Table II. End item visual defects Classification Major Minor Examine Defect Finish Cap not finished as specified Cap top not lusterless matte finish Chain

43、 and rivet not black oxidized coated Construction and Cap split or cracked 101 blistering, or distortion i02 workmanship Unsatisfactory molding e.g., chalking, Rivet loose or not set as specified 103 Gasket not tight pressed fit 104 Gasket not cylindrical in shape, too small 105 Gasket split, torn,

44、mutilated, or dis tort ed 106 Cap or gasket not clean e.g., evidence of oil, grease, or other foreign matter Has objectionable odor Less than 66 serrations Serrations not equally spaced Component missing 107 Chain not two links Chain does not turn freely on rivet Threads per inch More or less than e

45、ight Thread stripped Identification Not molded in, illegible, incorrect, markings incomplete, or wrong location 108 201 202 203 204 205 206 20 7 208 20 9 21 o 21 1 4.4.4 End item dimensional examination. The end items shall be examined for conformance to the dimensions specified on the drawings. Onl

46、y those dimensions that can be evaluated without damaging or disassembling the end items shall be examined. Any dimension not within the specified tolerance shall be classified as a defect. The lot size shall be expressed in units of caps. (see 6.5). The sample unit shall be one cap. The inspection

47、level shall be S-2 4.4.5 End item testing. The end items shall be tested for the characteristics listed in table ILI. The lot size shall be expressed in units of caps. The sample unit shall be one complete cap assembly. The inspection level shall be S-l. 7 Provided by IHSNot for ResaleNo reproductio

48、n or networking permitted without license from IHS-,-,-MIL-C-44217A TABLE III. End item test Requirement Test Characteristic par a gr a ph procedure Set of rivet 3.5.4 4.5.3 Cap strength 3.5.1 4.5.1 4.4.6 Packaging examination. The fully packaged end items shall be examined or the defects listed bel

49、ow. The lot size shall be expressed in units of shipping containers. fully packaged. The inspection level shall be S-2 (see 6.5). The sample unit shall be one shipping container Examine Defect Marking (exterior Omitted; incorrect; illegible; of improper and interior) size, location, sequence, or method o application Materials Any component missing, damaged, or not: as spec if ied Workmanship Inadequate applcation of components, such as