ARMY A-A-52468-1993 GASKET FILTER FLUID PRESSURE AUTOMOTIVE FUEL《汽车燃料压力流体过滤器垫片》.pdf

《ARMY A-A-52468-1993 GASKET FILTER FLUID PRESSURE AUTOMOTIVE FUEL《汽车燃料压力流体过滤器垫片》.pdf》由会员分享，可在线阅读，更多相关《ARMY A-A-52468-1993 GASKET FILTER FLUID PRESSURE AUTOMOTIVE FUEL《汽车燃料压力流体过滤器垫片》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、A-A-52468 rn 9999974 OL45L54 LBB rn I Beneficial comments, recommendations, additions, deletions clarifications, etc. I and any other data which may improve this document should be sent by letter to: U. S. Army Tank-Automotive Command, ATTN: AMSTA-GDS, Warren, MI 48397-5000. I NOT MEASUREMENT SENSIT

2、IVE A-A-5 2 468 July 20, 1993 SUPERSEDING MS51091B 29 December 1967 COMMERCIAL ITEM DESCRIPTION GASKET: FILTER, FLUID, PRESSURE, AUTOMOTIVE FUEL The General Services Administration has authorized the use of this commercial item description (CID) as a replacement for MCS1091B, which 4s canceled. ABST

3、RACT This CID covers a synthetic rubber gasket used in pressurized automotive fuel filters . SALIENT CHARACTERISTICS a. Material. The gasket shall be made of a low volume swell synthetic rubber designation M5BG610A14B24E014F17 or M5BG710A14B24E014F17 in accordance with American Society for Testing a

4、nd Materials (ASTM) standard D2000. The use of recovered materials made in compliance with regulatory requirements is acceptable providing that all requirements of this CID are met (see note e). 1. Age control. The maximum age of gaskets at the time of acceptance by the Government acquiring activity

5、 shall be no more than 40 quarters from the cure date. b. Gasket sizes. Gaskets shall be made in accordance with the sizes specified in figure 1. c. Storage. Gaskets shall be protected from circulating air, sunlight, fuel, oil, water, dust, and ozone during storage. Storage temperature shall not exc

6、eed 125 degrees Fahrenheit (OF) 52 degrees Celsius (OC). msc N/A FSC 2910 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52468 = 74 0145355 O14 CID PIN 2/ - A-A-

7、52 468 Diameter Width Superseded Diameter MS Part No. A B C -*1“ IA 52468-1 I II MS51091-1 3.270 + .O24 3.030 + -010 -125 + .O08 (83.0 - .5) l- (80.0 7 -2) l- (3.2 .2) - I O I-A-1.020 (.5) F.I.M. I MS51091-2 I 1.121 + -010 .858 + ,005 .161 + .O10 (28.5 T - .2) - (22.0 - + .i) l(4.0 T - .2) A 52468-5

8、 MS51091-5 I 2.110 + .O10 1.780 + .O10 I .O60 + .O10 - (53.5 5 - -2) i- (45.2 5 -2) l(1.5 - + -2) IA 52468-31 MS51091-3 11.000 + .O101 .485 + .OO5I.25 + .O101 l(25.5 - T .2) IA 52468-41 MS51091-4 :2.005 + .010!1.562 + .010i.062 + -010 - - - I ;(5i. i -2) ,(SS.l + -2) j(i.6 + -2) - - - i NOTES: 1. Di

9、mensions in inches (millimeters). 2/ PIN = Part or identification number. - FIGURE 1. Gasket sizes. d. Identification and marking. Identification and marking of the gaskets shall be as specified in the packaging requirements and shall include, as a minimum, the CID PIN, manufacturers CAGE code, and

10、material cure date (quarter and year). I 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52468 m 9999974 0345356 T50 D A-A-52 468 QUALITY ASSURANCE PROVISIONS a. Responsibility for inspection. The contractor is responsible for the A performance

11、 of all inspections (examinations and tests). b. Contractor certification. The contractor shall certify and maintain substantiating evidence that the product offered meets the salient characteristics of this CID and that the product conforms to the producers own drawings, specifications, workmanship

12、 standards, and quality assurance practices. Items with known defects shall not be submitted for Government acceptance. conformance prior to the first delivery and thereafter as may be otherwise provided for under the provisions of the contract. The Government reserves the right to require proof of

13、such PRESERVATION, PACKAGING, PACKING, LABELING, AND MARKING Presarvation, packaging, packing, labeling, and mzrking for the &sir& leve. shall be as specified in the contract (see salient characteristic d and note b). NOTES (This section contains information of a general or explanatory nature that a

14、. Addresses for obtaining copies of referenced Non-Government may be helpful, but is not mandatory.) publications. Copies of ASTD D2000 “Standard Classification System for Rubber Products in Automotive Applications“ are available from the American Society or Testing and Materials, 1916 Race Street,

15、Philadelphia, PA 19103. b. Ordering data. Acquisition documents must specify the following: 1. Title, number, and date of this CID. 2. Issue of DODISS to be cited in the solicitation, and if required, the 3. CID PIN. 4. Selection of applicable level and packaging requirements. specific issue of indi

16、vidual documents referenced. c. Part or identification number (PIN). The PIN to be used for gaskets acquired by this CID is as follows: A 52468 - X size (see figure i) CID number Commercial item description designator d. Cross-reference data. Gaskets conforming to this CID are substitutable/ interch

17、angeable with gaskets conforming to MS51091B, dated 29 December 1967, in accordance with figure 1. b e. Regulatory requirements. The offeror/contractcr is encouraged to use recovered materials in accordance with Public Law 94-580 to the maximum extent practicable. I 3 Provided by IHSNot for ResaleNo

18、 reproduction or networking permitted without license from IHS-,-,-A-A-524b8 MILITARY INTERESTS: Custodians Army - AT Air Force - 99 Review activities Army - ME DLA - cs User activity Navy - MC 9999974 0345357 997 A-A- 52 468 CIVIL AGENCY COORDINATING ACTIVITIES: GSA - FCAE PREPARING ACTIVITY: Army - AT (Project 2910-0230) 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-