ARMY A-A-52467-1993 SCOOTERS MOTOR ELECTRIC MOTOR DRIVEN THREE- AND FOUR-WHEEL MODIFIED COMMERCIAL《改良商用3和4轮汽油发动机驱动的滑板车电机》.pdf

《ARMY A-A-52467-1993 SCOOTERS MOTOR ELECTRIC MOTOR DRIVEN THREE- AND FOUR-WHEEL MODIFIED COMMERCIAL《改良商用3和4轮汽油发动机驱动的滑板车电机》.pdf》由会员分享，可在线阅读，更多相关《ARMY A-A-52467-1993 SCOOTERS MOTOR ELECTRIC MOTOR DRIVEN THREE- AND FOUR-WHEEL MODIFIED COMMERCIAL《改良商用3和4轮汽油发动机驱动的滑板车电机》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、A-A-52467 rn 9999974 O345520 429 m I l /NOT MEASUREMENT SENSITIVE/ A-A-52467 15 July 1993 SUPERSEDING MIL-S-62293C 28 September 1988 COMMERCIAL ITEM DESCRIPTIO SCOOTERS, MOTOR: ELECTRIC MOTOR DRIVEN, THREE- AND FOUR-WHEEL, MODIFIED COMMERCIAL This commercial item description is approved foi- use by

2、the US Army Tank-Automotive Command, Department of the Army, and is available for use by all Departments and Agencies of the Department of Defense. 1.1 Scope. This commercial item description (CID) covers electric motor driven, three and four wheel scooters. The scooters are for on-station transport

3、 of personnel and cargo under both indoor and outdoor operating conditions. Over-highway operation is not intended. 1.2 Classification. The scooter shall be one of the following types, specified (see 6.2), the vehicle may be either a model 3 (3-wheel) or a model 4 (4-wheel), at the manufacturers opt

4、ion. Combinations specified will be limited to those shown in table I. I payloads and models as specified (see 6.2). Unless a specific model is , Beneficial comments (recommendations, additions, deletions) and any 1 pertinent data which may be of use in improving this document should , be addressed

5、to: US Army Tank-Automotive Command, ATTN: AMSTA-UED, Warren, MI 48397-5000, by using the self-addressed Standardization I Document Improvement Proposal (DD Form 1426) appearing at the end 1 I I of this document or by letter. I AMSC N/A 1 1 1 FSC-23401 DISTRIBUTION STATEMENT A. Approved for public r

6、elease; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-524b7 M 9999974 0145521 3b5 I l I IV VI I I Payload capacity , model 3 , model 4 I A-A- 5 2 46 7 19 (12) 14 (9) 14 (9) i TABLE I. Body type, payload capacity and m

7、odel combinations. I Pickup 454 (1000) 10 (6) 680 (1500) 910 (2000) 1360 (3000) I a I I 29 (18) 1 19 (12) 14 (9) 14 (9) Personnel carrier, 454 (1000) - 16 (10) I l Body type ikilograms (kg) (pounds) j km/h (mph) km/h (mph) 1 - Deleted - 1 Stake and platform I 454 (1000) I 10 (6) 680 (1500) 10 (6) 91

8、0 (2000) 14 (9) - i 1360 (3000) - Refuse collection 1 454 (1000) I Burden carrier l i 1815 (4000) I I 2720 (6000) 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified here

9、in. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATIONS STANDARDS FEDERAL FED-STD-297 - Rustproofing of Commerci

10、al (Nontactical) Vehicles. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-524b7 9999974 0145522 2T1 m A-A- 5 2 4 6 7 MIL I TARY MIL-STD-1223 - Nontactical Wheeled Vehicles Treatment, Painting, Identification Marking and Data Plate Standards. (

11、Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Naval Publications and Forms Center, Military Specifications and Standards Bldg. 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.1.2 Other Government documents, drawings

12、, and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation. DEPARTMENT OF DEFENSE Department of Defense Index of Specifications and St

13、andards (DODISS). (Copies of the DODISS are available on a yearly subscription basis either from the Government Printing Office for hard copy, or microfiche copies are available from the Director, Navy Publication and Printing Service Office, 700 Robbins Avenue, Philadelphia, PA 19111-5093.) DEPARTM

14、ENT OF TRANSPORTATION (DOT) Federal Motor Vehicle Safety Standards (FMVSS). (Application for copies of DOT publications should reference the Code of Federal Regulations, 49 CFR, and the Federal Register, and should be addressed to the Superintendent of Documents, U.S. Government Printing Office, Was

15、hington, D.C. 20402.) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION (OSHA) Occupational Safety and Health Standards. (Application for copies of OSHA publications should reference the Code of Federal Regulations 29 CFR, Part 1910, and the Federal Register and should be addressed to the Superintendent

16、 of Documents, U.S. Government Printing Office, Washington, D.C. 20402.) 2.2 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted are those listed in the issue o

17、f the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS are the issues of the documents cited in the solicitation (see 6.2). 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52467 m 99

18、99974 0345523 138 m A-A- 524 67 THE EUROPEAN TYRE AND RIM TECHNICAL ORGANISATION (ETRTO) Standards Manual. (Application for copies of ETRTO publications should be addressed to the European Tyre and Rim Technical Organisation, 32, Avenue Brugmann, 1060 Brussels, Belgium.) SOCIETY OF AUTOMOTIVE ENGINE

19、ERS, INC. (SAE) SAE Standards and Recommended Practices 5551 - Performance Levels and Methods of Electromagnetic Radiation from Vehicles and Devices (30-1000 MHz). Truck-Trailer Jumper Cable. Vehicles. 5560 - Seven-Conductor Electrical Connector for 5695 - Turning Ability and Of Tracking - Motor (Ap

20、plication for copies of SAE publications should be addressed to SAE, Inc., 400 Commonwealth Drive, Warrendale, PA 15096.) THE TIRE AND RIM ASSOCIATION, INC. Year Book. (Application for copies of Tire and Rim Association publications should be addressed to The Tire and Rim Association, Inc., 175 Mont

21、rose West Ave., Copley, OH 44321.) (Non-Government standards and other publications are normally available from the organizations that prepare or distribute the documents. These documents also may be available in or through libraries or other informational services.) 2.3 Order o precedence. In the e

22、vent of a conflict between the text of this document and the references cited herein, the text of this document shall take precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3.1 Salient characteristics. The vehicle

23、 described by this CID is an electric motor driven scooter. The vehicle shall be procurable as an “off-the-shelf“, commercially produced, readily available item. The vehicle manufacturer shall have built similar model vehicles, as offered to the Government, for commercial sales for at least the past

24、 two years, at a rate of not less than 200 units a year. The manufacturer shall have multiple branches or dealers. The vehicle shall comply with listed applicable documents or their respective commercial counterparts. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without lic

25、ense from IHS-,-,-A-A- 5 2 4 6 7 3.1.1 Painting and marking. Treatment, painting, identification marking Exterior color and identification markings and data plates per MIL-STD-1223. per MIL-STD-1223 (see 6.2), for the military service identified by the procuring activity. 3.1.2 Rustproofing. To the

26、truck requirements of FED-STD-297. 3.1.3 Towing devices. When specified (see 6.2), not less than two towing devices, for towing the vehicle, on the front of the vehicle. 3.1.4 Pintle. When specified (see 6.2), a pintle assembly on the rear of the vehicle. Pintle of the fixed type, five-ton capacity,

27、 with locking pin and chain, Holland Hitch Model TOAL, or equal. Installed on the chassis or reinforced bumper with reinforcements to transfer pintle loads directly to the chassis. Rearmost part of the pintle not more than 100 millimeters (mm) (four inches) forward of the rearmost part of the vehicl

28、e. Pintle hook height to the centerline of the pintle hook on an unloaded vehicle from 300 to 460 mm (12 to 18 inches). Two trailer safety chain attachment devices, one adjacent to each side of the pintle. Each attachment providing an ultimate strength not less than the gross vehicle weight of the v

29、ehicle furnished. Pintle secured with a minimum of four 1/2-inch bolts. 3.1.5 Trailer lighting receptacle. When specified (see 6.2), on pintle-equipped vehicles, a 12-volt trailer lighting receptacle adjacent to the pintle, conforming to SA 5560 with its conductors connected and color-coded as speci

30、fied therein. 3.2 Design standards. Conform to electric vehicle requirements set forth in OSHA standards, section 1910.178 for powered industrial trucks, type E designation. 3.2.1 Dimensions. Dimensions as specified in table II. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted

31、without license from IHS-,-,-A-A-52467 m 9999974 0345525 TOO m A-A-52467 C 4 ln C ai E .4 n Y U w cl a: E m 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-524b7 m 9999974 0345526 947 Range A-A-52467 Gradeability 3.3 Performance. Meet the perfo

32、rmance requirements specified herein with the tires inflated to the rated tire pressure and vehicle operated on smooth, dry, level (except for gradeability requirements), hard surfaced, paved roads, and under standard temperature conditions that will allow or full battery capacity. , Body type Paylo

33、ad capacity I 3.3.1 Speed. Capable of transporting the operator at the rated speed for the specified scooter type and specified payload capacity (see table I) for a duration of not less than three minutes. 3.3.2 Range. Capable of transporting the operator, a front seat passenger, and the specified p

34、ayload capacity over the range specified in table III at an average speed of not less than 70 percent of the rated speed (see table I). Model 3 Model 4 1 (percent grade) 1 3.3.3 Gradeability. Capable of transporting the operator, a front seat passenger, and the specified payload capacity up the grad

35、e specified in table III for a duration of not less than three minutes. I I km/h (miles) kmjh (mi1es)lModel 3 1 Model 4 l kg (Pounds) I I I I , 77 1360 (3000) - 24 (15) -13 1 I 454 (1000) 1 32 (20) 32 (20) 680 (1500) I 40 (25) 40 (25) I717 910 (2000) 32 (20) I 32 (20) 515 I 1 32 (20) 7 7 7 5 40 (25)

36、 454 (1000) 680 (1500) 910 (2000) 32 (20) 32 (20) , 1360 (3000) - 24 (15) 1 - - 32 (20) - I 3.3.4 Turning clearance. Turn within a SAE 5695 vehicle clearance circle of not more than 7010 mm (23 feet) for types I to VI, and not more 3 1 I than 7600 mm (25 feet) for type VII. 1 III 1 454 (1000) 1 7 I7

37、 ! I l i 4 454 (1000) - 24 (15) - VI I ! i 11 I 11 1815 (4000) - 1 10 (6.5) - ! - i 11 (7) - I 2720 (6000) 1 1 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52467 9999974 0345527 883 A-A- 5 2 4 6 7 3.4.1 Construction. Type I and II, 3-wheel typ

38、e with single front and two rear wheels, or 4-wheel type. Type III, VI and VII, 4-wheel type only. Steering tiller or automotive steering wheel, except when specified (see 6.2), automotive type steering only. 3.4.1.1 Motorisi. Direct current. 3.4.1.2 Transmission. Sufficient torque capacity. 3.4.1.3

39、 Speed controller. Accelerator pedal. 3.4.1.4 Speed selector. Permit forward and reverse speeds. When specified (see 6.2), provisions to limit the rate of power application. 3.4.1.5 Accelerator pedal. Foot pedal, automotive type. When specified (see 6.2), provisions to limit the rate of power applic

40、ation. 3.4.1.6 Operating key switch. Automotive ignition type. 3.4.1.7 Deadman seat switch. Operator must be in seated position to enable vehicle operation. 3.4.1.8 Motor overload protection. Manufacturers standard. 3.4.1.9 Batteries. Deep-cycle type. 3.4.1.10 Battery condition meter. Visual type. 3

41、.4.1.11 Battery charging system. Consisting of a charger and the accessories required to connect the vehicle batteries through the charger to a 60 Hertz alternating current (ac) power source. Fully automatic, line compensating type with voltage sensing device to automatically reduce/shut down curren

42、t at near end/end of charge cycle. Capable of fully charging complete battery set within 12 hours. Chargers to be furnished as separate units. Type I, II, III and V 120 volts. Type VI1 240 volt. Cable length 2030 mm (80 inches) minimum. When specified (see 6.2), chargers for type I, II, III and VI v

43、ehicles built into the scooter. 3.4.1.12 Radio interference suppression. Suppressed to limit electromagnetic radiation within the limits specified by SAE 5551. 3.4.2 Accessory electrical equipment. 3.4.2.1 Accessories. 12-volt electrical equipment shall include: (a) At least one headlight (b) Tailli

44、ght (c) Stoplight or combination stoplight and taillight 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A -Am5 2 4 b 7 m 9999974 0345528 7LT m A-A- 5 2 4 6 7 (d) Turn signals (e) Horn, and (f) Light switch. When specified (see 6.2), two headlights

45、 and two taillights. 3.4.2.2 Hour meter. When specified (see 6.2), an hour meter having a totalizing mechanism of not less than 9,999 hours. 3.4.2.3 Vehicle approach warning device. Pulsating alarm warning device (beeper ) . 3.4.4 Suspension. Springs or manufacturers heavy duty shear mounts on the f

46、ront and springs on the rear. Shock absorber(s) both front and rear. 3.4.5 Wheels, rims, tires and tubes. Single wheels. Rims and tire ratings conforming to Tire and Rim Association or European Tyre and Rim Technical Organisation recommendations. Tire and rim sizes and load ratings the same or all w

47、heels, except or type VII. No multi-piece rims. 3.4.5.1 Tires. Pneumatic, tube or tubeless type with highway tread, except for solid tires on type VII. 3.4.6 Service brakes. Hydraulic or mechanical. Brake linings of nonasbestos material. 3.4.6.1 Parkina brakes. Hand operated. 3.4.7 Bumper. Manufactu

48、rers standard full width front bumper. Type VII, not less than 4.8 mm (0.188 inch) thick diamond plate lower front panel. 3.4.8 Rearview mirrors. Adjustable. Provided on the right and left sides. 3.4.9 Light bar. When specified (see 6.2), mounted on the roof of the cab. Fabricated of not less than 1

49、6 gage (1.519 mm) (0.0598 inch) steel, not less than 810 mm (32 inches) in length and 280 mm (11 inches) in width. 3.4.10 - Cab. Type I, II, III, VI and, when specified (see 6.2), type VI1 provided with a detachable, enclosed cab of rigid construction. Side closures on type I, II, III, VI and VI1 weatherproof cloth doors or, when specified (see 6.2), weatherproof, lockable rigid doors