ARMY A-A-52466-1993 SCOOTERS MOTOR GASOLINE ENGINE DRIVEN THREE- AND FOUR-WHEEL MODIFIED COMMERCIAL《改良商用3和4轮汽油发动机驱动的滑板车电机》.pdf

《ARMY A-A-52466-1993 SCOOTERS MOTOR GASOLINE ENGINE DRIVEN THREE- AND FOUR-WHEEL MODIFIED COMMERCIAL《改良商用3和4轮汽油发动机驱动的滑板车电机》.pdf》由会员分享，可在线阅读，更多相关《ARMY A-A-52466-1993 SCOOTERS MOTOR GASOLINE ENGINE DRIVEN THREE- AND FOUR-WHEEL MODIFIED COMMERCIAL《改良商用3和4轮汽油发动机驱动的滑板车电机》.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、A-A-524bb 74 0345286 679 = . I /NOT MEASUREMENT SENSITIVE/ l I 1 A-A- 52 466 15 July 1993 SUPERSEDING MIL-s-45324L 12 December 1990 COMMERCIAL ITEM DESCRIPTION SCOOTERS, MOTOR: GASOLINE ENGINE DRIVEN, THREE- AND FOUR-WHEEL, MODIFIED COMMERCIAL This commercial item description is approved for use by

2、the US Army Tank-Automotive Command, Department of the Army, and is available for use by all Departments and Agencies of the Department of Defense. 1.1 Scope. This commercial item description (CID) covers gasoline engine driven three-wheeled scooters intended for both local streets and roads and on-

3、station operation, and four-wheeled scooters restricted to on-station operation (see 6.1 for details on restricted use). 1.2 Classification. The scooter shall be one of the following styles, as specified (see 6.2): O Style A - Scooter, 454 kilograms (kg) (1,000 pound) flatbed, with panel sides and t

4、ailgate. Style B - Scooter, with enclosed lockable package compartment. Style C - Scooter, with integral van body. Style D - Scooter, with integral van body and rear passenger seats. Style E - Scooter, refuse collection. Style F - Scooter, 910 kg (2,000 pound) flatbed. style G - Scooter, 680 kg (1,5

5、00 pound) flatbed, wide tread, with panel sides and tailgate. 1 I ! I Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: US Army Tank-Automotive Command, ATTN: AMSTA-WED, Warren, MI 48397-5000, by

6、using the self-addressed Standardization l Document Improvement Proposal (DD Form 1426) appearing at the end of I this document or by letter. I AMSC NIA DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permit

7、ted without license from IHS-,-,-A-A-52466 9999974 0345287 505 m Scooter style A-A- 5 2 4 6 6 Models available Classes available 1.2.1 Model. The model of the scooter shall be determined by the intended usage and by the number of wheels, as specified (see 6.2): 1 2 3 1 2 3 Model 1 - On-road, 3-wheel

8、 Model 2 - On-station, 4-wheel Model 3 - On-station, 3-wheel. - 11 III - II III 1.2.2 Class. The class of the scooter shall be determined by the cab enclosure, as specified (see 6.2): Class I - Integral cab and body Class II - Enclosed drivers cab, separate from body Class III - Open drivers area. 1

9、.2.3 Combinations. The combinations of style, model, and class ordered under this CID shall be limited to those shown in table I. 2.1 Government documents. 2.1.1 Specifications, standards and handbooks. The following specifications, standards and handbooks form a part of this document to the extent

10、specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS), and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATIONS STANDARDS FEDERAL FED-STD-297 MIL I TARY

11、MIL-STD-461 - Rustproofing of Commercial (Nontactical) Vehicles. - Electromagnetic Interference Characteristics Requirements for Equipment. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-524bb W 9999974 0145288 441 A-A-52466 MIL-STD-1223 - Non

12、tactical Wheeled Vehicles Treatment, Painting, Identification Marking, and Data Plate Standards. (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Naval Publications and Forms Center, Military Specifications and Standards, Bld

13、g. 4D, 7Ud Robbins Avenue, Philadelphia, PA 19111-5094.) 2.1.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those ci

14、ted in the solicitation. DEPARTMENT OF DEFENSE Department of Defense Index of Specifications and Standards (DODISS). (Copies of the DODISS are available on a yearly subscription basis either from the Government Printing Office for hard copy, or microfiche copies are available from the Director, Navy

15、 Publication and Printing Service Office, 700 Robbins Avenue, Philadelphia, PA 19111-5093.) DEPARTMENT OF TRANSPORTATION (DOT) Federal Motor Carrier Safety Regulations (FMCSR). Federal Motor Vehicle Safety Standards (FMVSS). (Application for copies of DOT publications should reference the code of Fe

16、deral Regulations, 49 CFR, and the Federal Register and should be addressed to the Superintendent of Documents, U.S. Government Printing Office, Washington, D.C. 20402.) ENVIRONMENTAL PROTECTION AGENCY (EPA) Regulations and Appendices. Certification and Test Procedures for New Motorcycles; Emission

17、EPA Noise Emission Regulations for Motorcycles. (Application for copies of EPA publications should reference the Code of Federal Regulations, 40 CFR, and the Federal Register and should be addressed to the Superintendent of Documents, U.S. Government Printing Office, Washington, D.C. 20402.) OCCUPAT

18、IONAL SAFETY AND HEALTH ADMINISTRATION (OSHA) Standards. (Application for copies of OSHA publications should reference the Code of Federal Regulations 29 CFR, Part 1910, and the Federal Register and should be addressed to the Superintendent of Documents, U.S. Government Printing Office, Washington,

19、D.C. 20402.) 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-524bb 9999974 0145289 388 8 A-A-524 66 a 2.2 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specifi

20、ed, the issues of the documents which are DoD adopted are those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS are the issues of the documents cited in the solicitation (see 6.2). THE EUROPEAN TYRE AND RIM TEC

21、HNICAL ORGANISATION (ETRTO) Standards Manual. (Application or copies of ETRTO publications should be addressed to the European Tyre and Rim Technical Organisation, 32, Avenue Brugmann, 1060 Brussels, Belgium.) SOCIETY OF AUTOMOTIVE ENGINEERS, INC. (SAE) CAE Standards and Recommended Practices. 5551

22、- Performance Levels and Methods of Measurement of Electromagnetic Radiation from Vehicles and Devices (30-1000 MHz). 5560 - Seven-Conductor Electrical Connector for Truck-Trailer Jumper Cable. 5695 - Turning Ability and Off Tracking. (Application for copies of SAE publications should be addressed t

23、o CAE, Inc., 400 Commonwealth Drive, Warrendale, PA 15096.) THE TIRE AND RIM ASSOCIATION, INC. Year Book. (Application for copies of Tire and Rim Association publications should be addressed to The Tire and Rim Association, Inc., 175 Montrose West Ave., Copley, OH 44321.) (Non-Government standards a

24、nd other publications are normally available from the organizations that prepare or distribute the documents. These documents also may be available in or through libraries or other informational services.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the

25、references cited herein, the text of this document shall take precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3.1 Salient characteristics. The vehicle described by this CID is a gasoline engine driven motor scoo

26、ter. The vehicle shall be procurable as an “off-the-shelf“, commercially produced, readily available item. The vehicle manufacturer shall have built similar model vehicles, as offered to the 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52466

27、 9999974 0345290 OTT W A-A- 5 2 4 6 6 ;. Government, of not less branches or for commercial sales for at least the past two years, at a rate than 200 units a year. The manufacturer shall have multiple dealers. The vehicle shall comply with listed applicable documents or their respective commercial c

28、ounterparts. 3.1.1 Painting and marking. Treatment, painting, identification marking and data plates per MIL-STD-1223. Exterior color and identification markings per MIL-STD-1223 for ,;he military service identified by the procuring activity (see 6.2). 3.1.2 Rustproofing. In accordance to the truck

29、requirements of FED-STD-297. 3.1.3 Pintle. When Specified (see 6.2), a pintle assembly on the rear of model 2 or 3 vehicles. Pintle of the fixed type, five-ton capacity, with locking pin and chain, Holland Hitch Model T60AL. Pintle installed on the chassis or reinforced bumper with reinforcements to

30、 transfer pintle loads directly to the frame. Rearmost part of the pintle not more than 100 millimeters (mm) (four inches) forward of the rearmost part of the vehicle. Pintle hook height to the centerline of the pintle hook on the loaded vehicle in the range of 300 to 460 mm (12 to 18 inches). Two t

31、railer safety chain attachment devices, one adjacent to each side of the pintle. Each attachment providing an ultimate strength not less than the gross vehicle weight of the vehicle furnished. Pintle secured with a minimum of four 0.500 inch bolts. 3.1.4 Trailer lighting receptacle. When specified (

32、see 6.2), on pintle-equipped vehicles, a 12-volt trailer lighting receptacle on the rear adjacent to the pintle, conforming to SAE 5560 with its conductors connected and color coded as specified therein. 3.1.5 Special radio interference suppression. When specified (see 6.2), for vehicles operating i

33、n critical communications areas, electromagnetic radiation suppressed in accordance with the requirements of MIL-STD-461 for class IIIC equipment in lieu of 3.4.7.4. 3.2 General design. 3.2.1 Model 1 desian standards. 3.2.1.1 FMVSS. Model 1 scooter to all FMVSSs as applicable to motorcycles. 3.2.1.2

34、 Interior sound level. Model 1, class 1 and 2 to FMCSR 393.94, except when cloth cab doors are furnished. 3.2.1.3 Exterior noise level. Model 1 to EPA Noise Emission Regulations for Motorcycles. Vehicles destined for California to the California Vehicle code. 5 Provided by IHSNot for ResaleNo reprod

35、uction or networking permitted without license from IHS-,-,-A-A-52466 = 9999974 0145291 T3b H 1 1 2 2 2 2 3 3 A-A-52 466 454 (1,000) 454 (1,000) 370 (825) 136 (300) 910 (2,000) 910 (2,000) 680 (1,500) 3.2.1.4 Air pollution control. Model 1 to EPA regulations governing Certification and Test Procedur

36、es or New Motorcycles; Emission Regulations and Appendices. 3.2.2 Model 2 and model 3 design standards. 3.2.2.1 OSHA standards. Model 2 and model 3 to vehicle requirements set forth in the OSHA standards, section 1910.178, or powered industrial trucks, type G designation. 3.2.3 Curb weight. Not less

37、 than 410 kg (900 pounds). 3.2.4 Total rated payload. As specified in table II. TABLE II. Total rated Pavload. I Style iG Loadspace Payload Model 1 kg (pounds ) Operat or kg (pounds) 80 (175) 80 (175) 80 (175) 80 (175) 80 (175) 80 (175) 80 (175) Passenger(s) kg (pounds) 80 (175) 80 (175) 320 (700) 8

38、0 (175) 80 (175) - I Total rated payload I i kg (pounds) I 530 (1,175) i 610 (1,350) I i 1070 (2,350) l 990 (2,175) ! 530 (1,175) 530 (1,175) I 840 (1,850) I 3.2.5 Vehicle dimensions. As specified in table III. TABLE III. Dimensions. Feature Wheelbase (minimum) Wheel tread (minimum) Overall length (

39、maximum) Overall width (minimum) Model 1 All style: mm (inch) 1980 (78) 1040 (41) 3230 (127) 1190 (47) Model 2 All styles mm (inch) 2130 (84) 1040 (41) 3050 (120) i/ - 1190 (47) Style A mm (inch) 1980 (78) 1040 (41) 2850 (112) 1190 (47) Model .3 Style F mm (inch) 2130 (84) 1040 (41) 3350 (132) 1190

40、(47) I mm (inch) 1980 (78) 1140 (45) 3180 (125) 1370 (54) 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52466 - 9999974 0145292 972 Model 1 Model 2 I Model 3 All styles All styles Style A Style F Style G , I A-A- 5 2 46 6 TABLE III. Dimension

41、s. (continued) Feature mm (inch) ; mm (inch) lmm (inch) i l I l l l 11800 (71) I Overall height, class I and class II ( maximum ) 1800 (71) /1800 (71) mm (inch) (mm (inch) l i 1800 (71) 1830 (72)j I 3.3.1 Maximum geared speed. Unless a pintle assembly is required, a maximum geared speed at engine go

42、verned speed within 5 percent of the speed listed in table IV as the standard speed for the body style and model specified. When specified (see 6.2), the optional geared speed specified in table IV by use of an optional rear axle ratio. When a pintle is required, maximum geared speed not exceeding 3

43、9 kilometers per hour (km/h) (24 miles O per hour (mph). Overall height, class III excluding mirrors) (maximum TABLE IV. Maximum speeds (nominal). I l I i j I I I l 1190 (47) 1220 (48) 11190 (47) 1190 (47) 1270 (50) Style speed speed Model D A E F F G 3.3.2 Gradeability. High speed gradeability to b

44、e met with the transmission in the highest gear; low speed gradeability in first gear. Based on the required maximum geared speed, the scooter to ascend the continuous grades specified in table VI when loaded with the payload specified in table V. 2 3 1 2 3 3 7 47 (29) 30 (18) 30 (18) 37 (23) 30 (18

45、) - - 1 - Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A- 52 4 66 TABLE V. Gradeability. 30 (18) 35 or 37 (22 or 23) 63 (39) I 47 (29) I Payload Percent grade Percent grade kg (pounds) I Required maximum geared speed km/h (mph) 454 (1,000) I 9 1

46、 25 680 (1,500) 1 8 I 20 454 (1,000) 7 20 454 (1,000) 4 3.3.3 Drawbar pull. When a pintle is required, capable of developing a continuous first gear drawbar pull of 340 kg (750 pounds). When an auxiliary transmission is specified for pintle-equipped style GI drawbar pull of not less than 454 kg (1,0

47、00 pounds). 3.3.4 Turning clearance. Turn within an SAE 5695 vehicle clearance circle of not more than 7600 mm (25 feet). 3.3.5 Service brake performance. On model 1 to FMVSS No. 122. On model 2 and model 3 stop and hold the vehicle loaded with total rated payload on a 25 percent grade, and stop the

48、 fully loaded scooter within a distance of 9140 mm (30 feet) from a speed of 29 km/h (18 mph) on smooth, dry, level, hard-surfaced road. 3.3.6 Parking brake performance. Model 1 to FMVSS No. 122. Model 2 and 3 hold the vehicle, loaded with total rated payload, on grade of not less than 20 percent. 3

49、.4 Chassis. Model 1 and model 3 three wheel with single front and two rear wheels. Model 2 four wheels. All front wheel steering and rear wheel driving. 3.4.1 Engine and drivetrain. Four-stroke cycle gasoline. Not less than 18 horsepower at a governed speed not greater than 3600 revolutions per minute (rpm) . 3.4.1.1 Oil filter. Full-flow type. 3.4.1.2 Governor. Set to engine manufacturers maximum recommended op