ISO 4570-2002 Tyre valve threads《轮胎气门嘴螺纹》.pdf
《ISO 4570-2002 Tyre valve threads《轮胎气门嘴螺纹》.pdf》由会员分享,可在线阅读,更多相关《ISO 4570-2002 Tyre valve threads《轮胎气门嘴螺纹》.pdf(10页珍藏版)》请在麦多课文档分享上搜索。
1、 Reference number Numro de rfrence ISO 4570:2002(E/F) ISO 2002INTERNATIONAL STANDARD NORME INTERNATIONALE ISO 4570 First edition Premire dition 2002-03-15 Tyre valve threads Filetages de valves pour pneumatiques ISO 4570:2002(E/F) PDF disclaimer This PDF file may contain embedded typefaces. In accor
2、dance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes li
3、censing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for print
4、ing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. PDF Exonration de responsabilit Le prsent fichier PDF peut contenir des pol
5、ices de caractres intgres. Conformment aux conditions de licence dAdobe, ce fichier peut tre imprim ou visualis, mais ne doit pas tre modifi moins que lordinateur employ cet effet ne bnficie dune licence autorisant lutilisation de ces polices et que celles-ci y soient installes. Lors du tlchargement
6、 de ce fichier, les parties concernes acceptent de fait la responsabilit de ne pas enfreindre les conditions de licence dAdobe. Le Secrtariat central de lISO dcline toute responsabilit en la matire. Adobe est une marque dpose dAdobe Systems Incorporated. Les dtails relatifs aux produits logiciels ut
7、iliss pour la cration du prsent fichier PDF sont disponibles dans la rubrique General Info du fichier; les paramtres de cration PDF ont t optimiss pour limpression. Toutes les mesures ont t prises pour garantir lexploitation de ce fichier par les comits membres de lISO. Dans le cas peu probable o su
8、rviendrait un problme dutilisation, veuillez en informer le Secrtariat central ladresse donne ci-dessous. ISO 2002 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
9、and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. / Droits de reproduction rservs. Sauf prescription diffrente, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et
10、par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de lISO ladresse ci-aprs ou du comit membre de lISO dans le pays du demandeur. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightis
11、o.ch Web www.iso.ch Printed in Switzerland/Imprim en Suisse ii ISO 2002 All rights reserved/Tous droits rservs ISO 4570:2002(E/F) ISO 2002 All rights reserved/Tous droits rservs iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodie
12、s (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations,
13、 governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO
14、/IEC Directives, Part 3. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the m
15、ember bodies casting a vote. Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 4570 was prepared by Technical Committee ISO/TC 31, Ty
16、res, rims and valves, Subcommittee SC 9, Valves for tube and tubeless tyres. It cancels and replaces ISO 4570-1:1977, ISO 4570-2:1979 and ISO 4570-3:1980, of which it constitutes a technical revision. ISO 4570:2002(E/F) iv ISO 2002 All rights reserved/Tous droits rservs Avant-propos LISO (Organisati
17、on internationale de normalisation) est une fdration mondiale dorganismes nationaux de normalisation (comits membres de lISO). Llaboration des Normes internationales est en gnral confie aux comits techniques de lISO. Chaque comit membre intress par une tude a le droit de faire partie du comit techni
18、que cr cet effet. Les organisations internationales, gouvernementales et non gouvernementales, en liaison avec lISO participent galement aux travaux. LISO collabore troitement avec la Commission lectrotechnique internationale (CEI) en ce qui concerne la normalisation lectrotechnique. Les Normes inte
19、rnationales sont rdiges conformment aux rgles donnes dans les Directives ISO/CEI, Partie 3. La tche principale des comits techniques est dlaborer les Normes internationales. Les projets de Normes internationales adopts par les comits techniques sont soumis aux comits membres pour vote. Leur publicat
20、ion comme Normes internationales requiert lapprobation de 75 % au moins des comits membres votants. Lattention est appele sur le fait que certains des lments de la prsente Norme internationale peuvent faire lobjet de droits de proprit intellectuelle ou de droits analogues. LISO ne saurait tre tenue
21、pour responsable de ne pas avoir identifi de tels droits de proprit et averti de leur existence. LISO 4570 a t labore par le comit technique ISO/TC 31, Pneus, jantes et valves, sous-comit SC 9, Valves pour pneus avec chambres et sans chambre. Elle annule et remplace lISO 4570-1:1977, lISO 4570-2:197
22、9 et lISO 4570-3:1980, dont elle constitue une rvision technique. INTERNATIONAL STANDARD NORME INTERNATIONALE ISO 4570:2002(E/F) ISO 2002 All rights reserved/Tous droits rservs 1Tyre valve threads Filetages de valves pour pneumatiques 1 Scope This International Standard specifies limit dimensions an
23、d tolerances for three series of tyre valve threads: 5V1, 5V2, 6V1 and 8V1; 9V1, 10V2, 12V1, 13V1; 8V2, 10V1, 11V1, 13V2, 15V1, 16V1, 17V1, 17V2, 17V3, 19V1 and 20V1. 1 Domaine dapplication La prsente Norme internationale spcifie les dimensions limites et les tolrances pour trois sries de filetages
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO45702002TYREVALVETHREADS 轮胎 气门 螺纹 PDF
