ISO 22734-2-2011 Hydrogen generators using water electrolysis process - Part 2 Residential applications《采用水电解工艺的氢气发生器 第2部分 住宅应用》.pdf

《ISO 22734-2-2011 Hydrogen generators using water electrolysis process - Part 2 Residential applications《采用水电解工艺的氢气发生器 第2部分 住宅应用》.pdf》由会员分享，可在线阅读，更多相关《ISO 22734-2-2011 Hydrogen generators using water electrolysis process - Part 2 Residential applications《采用水电解工艺的氢气发生器 第2部分 住宅应用》.pdf（52页珍藏版）》请在麦多课文档分享上搜索。

1、Hydrogen generators using water electrolysis process Part 2: Residential applications Gnrateurs dhydrogne utilisant le procd dlectrolyse de leau Partie 2: Applications rsidentielles ISO 2011 Reference number ISO 22734-2:2011(E) First edition 2011-11-15 ISO 22734-2 INTERNATIONAL STANDARDISO 22734-2:2

2、011(E)COPYRIGHT PROTECTED DOCUMENT ISO 2011 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the add

3、ress below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2011 All rights reservedISO 22734-2:2011(E) ISO 2011 All rights

4、reserved iii Contents Page Foreword . v Introduction .vi 1 Scope 1 2 Normative references . 1 3 Terms and definitions . 5 4 Operating conditions 6 4.1 Energy consumption 6 4.2 Feed water specifications . 6 4.3 Ambient environment . 7 4.4 Purge gas . 7 4.5 Oxygen venting 7 4.6 Hydrogen venting 7 4.7

5、Delivery of hydrogen 8 5 Mechanical equipment . 8 5.1 General requirements . 8 5.2 General materials requirements 9 5.3 Enclosures 9 5.4 Pressure-bearing components 11 5.5 Fans and ventilators .13 5.6 Pumps .13 5.7 Heat transfer system 13 5.8 Connection to potable water 14 6 Electrical equipment, wi

6、ring and ventilation .14 6.1 Fire and explosion hazard protection requirements .14 6.2 Electrical equipment .16 7 Control systems .18 7.1 General .18 7.2 Control function in the event of failure19 7.3 Programmable electronic equipment .19 7.4 Start .19 7.5 Emergency stop .19 7.6 Stop .20 7.7 Self-co

7、rrectable conditions 20 7.8 Interconnected installations .20 7.9 Safety components .20 7.10 Remote control systems .21 7.11 Alarms 21 7.12 Purge gas quantity 21 7.13 Reset .21 7.14 Suspension of safeguards 21 8 Ion transport medium .21 8.1 Electrolyte .21 8.2 Membrane 22 9 Protection of service pers

8、onnel 22 10 Test methods 23 10.1 Type (qualification) tests .23 10.2 Routine tests .33 11 Marking and labelling .34 11.1 General requirements .34 11.2 Hydrogen generator marking .34ISO 22734-2:2011(E)iv ISO 2011 All rights reserved 11.3 Marking of components .35 11.4 Warning signs.35 12 Documentatio

9、n accompanying the hydrogen generator 35 12.1 General .35 12.2 Hydrogen generator ratings .36 12.3 Hydrogen generator installation .36 12.4 Hydrogen generator operation 38 12.5 Hydrogen generator maintenance 39 Annex A (informative) Hydrogen-assisted corrosion 40 Annex B (informative) Flammability l

10、imits of hydrogen .41 Bibliography .42Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body

11、 interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotec

12、hnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by

13、the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent righ

14、ts. ISO shall not be held responsible for identifying any or all such patent rights. ISO 22734-2 was prepared by Technical Committee ISO/TC 197, Hydrogen technologies. ISO 22734 consists of the following parts, under the general title Hydrogen generators using water electrolysis process: Part 1: Ind

15、ustrial and commercial applications Part 2: Residential applications ISO 22734-2:2011(E) ISO 2011 All rights reserved vIntroduction The technology in this part of ISO 22734 is as follows. In a hydrogen generator cell, electricity causes dissociation of water into hydrogen and oxygen molecules. An el

16、ectric current is passed between two electrodes separated by a conductive electrolyte or “ion transport medium”, producing hydrogen at the negative electrode (cathode) and oxygen at the positive electrode (anode). As water is H 2 O, twice the volume of hydrogen is produced compared with oxygen. Hydr

17、ogen gas produced using electrolysis technology can be utilized immediately or stored for later use. The cell(s), and electrical, gas processing, ventilation, cooling, monitoring equipment and controls are contained within an enclosure. Gas compression and feed water conditioning and auxiliary equip

18、ment may also be included. ISO 22734-2:2011(E)vi ISO 2011 All rights reservedINTERNATIONAL STANDARD ISO 22734-2:2011(E) Hydrogen generators using water electrolysis process Part 2: Residential applications 1 Scope This part of ISO 22734 defines the construction, safety and performance requirements o

19、f packaged hydrogen gas generation appliances, herein referred to as hydrogen generators, using electrochemical reactions to electrolyse water to produce hydrogen. This part of ISO 22734 is applicable to hydrogen generators that use the following types of ion transport medium: group of aqueous bases

20、; solid polymeric materials with acidic function group additions, such as acid proton exchange membrane (PEM). This part of ISO 22734 is applicable to hydrogen generators intended for indoor and outdoor residential use in sheltered areas, such as car-ports, garages, utility rooms and similar areas o

21、f a residence. This part of ISO 22734 includes cord-connected equipment for outdoor and garage use only. Portable generators as well as hydrogen generators that can also be used to generate electricity, such as reversible fuel cells, are excluded from the scope of this part of ISO 22734. Hydrogen ge

22、nerators that also supply oxygen as a product are excluded from the scope of this part of ISO 22734. This part of ISO 22734 is intended to be used for certification purposes. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated r

23、eferences, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies ISO 1182, Reaction to fire tests for products Non-combustibility test ISO 3746, Acoustics Determination of sound power levels and sound energy levels of

24、 noise sources using sound pressure Survey method using an enveloping measurement surface over a reflecting plane ISO 3864-2, Graphical symbols Safety colours and safety signs Part 2: Design principles for product safety labels ISO 4126-1, Safety devices for protection against excessive pressure Par

25、t 1: Safety valves ISO 4126-2, Safety devices for protection against excessive pressure Part 2: Bursting disc safety devices ISO 4126-6, Safety devices for protection against excessive pressure Part 6: Application, selection and installation of bursting disc safety devices ISO 7000, Graphical symbol

26、s for use on equipment Index and synopsis ISO 2011 All rights reserved 1ISO 7010, Graphical symbols Safety colours and safety signs Registered safety signs ISO 7866, Gas cylinders Refillable seamless aluminium alloy gas cylinders Design, construction and testing ISO 9300, Measurement of gas flow by

27、means of critical flow Venturi nozzles ISO 9951, Measurement of gas flow in closed conduits Turbine meters ISO 9614-1, Acoustics Determination of sound power levels of noise sources using sound intensity Part 1: Measurement at discrete points ISO 9809-1, Gas cylinders Refillable seamless steel gas c

28、ylinders Design, construction and testing Part 1: Quenched and tempered steel cylinders with tensile strength less than 1 100 MPa ISO 10286, Gas cylinders Terminology ISO 10790, Measurement of fluid flow in closed conduits Guidance to the selection, installation and use of Coriolis meters (mass flow

29、, density and volume flow measurements) ISO 11119 -1, Gas cylinders of composite construction Specification and test methods Part 1: Hoop wrapped composite gas cylinders and tubes ISO 11119 -2, Gas cylinders of composite construction Specification and test methods Part 2: Fully wrapped fibre reinfor

30、ced composite gas cylinders with load-sharing metal liners ISO 11119 - 3, Gas cylinders of composite construction Specification and test methods Part 3: Fully wrapped fibre reinforced composite gas cylinders and tubes with non-metallic and non-load-sharing metal liners ISO 12100, Safety of machinery

31、 General principles for design Risk assessment and risk reduction ISO 12499, Industrial fans Mechanical safety of fans Guarding ISO 13709, Centrifugal pumps for petroleum, petrochemical and natural gas industries ISO 13850, Safety of machinery Emergency stop Principles for design ISO 13854, Safety o

32、f machinery Minimum gaps to avoid crushing of parts of the human body ISO 13857, Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs ISO 14511, Measurement of fluid flow in closed conduits Thermal mass flowmeters ISO 14687 (all parts), Hydrogen fuel Pr

33、oduct specification ISO 14847, Rotary positive displacement pumps Technical requirements ISO 15534-1, Ergonomic design for the safety of machinery Part 1: Principles for determining the dimensions required for openings for whole-body access into machinery ISO 15534-2, Ergonomic design for the safety

34、 of machinery Part 2: Principles for determining the dimensions required for access openings ISO 15649, Petroleum and natural gas industries Piping ISO/TR 15916, Basic considerations for the safety of hydrogen systems ISO 16111, Transportable gas storage devices Hydrogen absorbed in reversible metal

35、 hydride ISO 16528-1, Boilers and pressure vessels Performance requirements ISO 17398, Safety colours and safety signs Classification, performance and durability of safety signs ISO 22734-2:2011(E)2 ISO 2011 All rights reservedISO 22734-1, Hydrogen generators using water electrolysis process Part 1:

36、 Industrial and commercial applications ISO 26142, Hydrogen detection apparatus Stationary applications IEC 60034-1, Rotating electrical machines Part 1: Rating and performance IEC 60068-2-18:2010, Environmental Testing Part 2-18: Tests Test R and Guidance: Water IEC 60079-0, Explosive atmospheres P

37、art 0: Equipment General requirements IEC 60079-2:2007, Explosive atmospheres Part 2: Equipment protection by pressurized enclosures “p” IEC 60079-10-1, Explosive atmospheres Part 10-1: Classification of areas Explosive gas atmospheres IEC 60079-29-2, Explosive atmospheres Part 29-2: Gas detectors S

38、election, installation, use and maintenance of detectors for flammable gases and oxygen IEC 60079-30-1, Explosive atmospheres Part 30-1: Electrical resistance trace heating General and testing requirements IEC 60146 (all parts), Semiconductor converters IEC 60204-1:2005, Safety of machinery Electric

39、al equipment of machines Part 1: General requirements IEC/TR 60269-5, Low-voltage fuses Part 5: Guidance for the application of low-voltage fuses IEC 60335-1:2010, Household and similar electrical appliances Safety Part 1: General requirements IEC 60335-2-41, Household and similar electrical applian

40、ces Safety Part 2-41: Particular requirements for pumps IEC 60335-2-51, Household and similar electrical appliances Safety Part 2-51: Particular requirements for stationary circulation pumps for heating and service water installations IEC 60335-2-80, Household and similar electrical appliances Safet

41、y Part 2-80: Particular requirements for fans IEC 60364-4-43, Low-voltage electrical installations Part 4-43: Protection for safety Protection against overcurrent IEC 60364-6:2006, Low-voltage electrical installations Part 6: Verification IEC 60417, Graphical symbols for use on equipment IEC 60439-1

42、, Low-voltage switchgear and controlgear assemblies Part 1: Type-tested and partially type- tested assemblies IEC 60439-2, Low-voltage switchgear and controlgear assemblies Part 2: Particular requirements for busbar trunking systems (busways) IEC 60439-3, Low-voltage switchgear and controlgear assem

43、blies Part 3: Particular requirements for low- voltage switchgear and controlgear assemblies intended to be installed in places where unskilled persons have access for their use Distribution boards IEC 60439-5, Low-voltage switchgear and controlgear assemblies Part 5: Particular requirements for ass

44、emblies for power distribution in public networks IEC 60445, Basic and safety principles for man-machine interface, marking and identification Identification of equipment terminals, conductor terminations and conductors IEC 60364-6:2006, Low-voltage electrical installations Part 6: Verification IEC

45、60529, Degrees of protection provided by enclosures (IP Codes) ISO 22734-2:2011(E) ISO 2011 All rights reserved 3IEC 60534 (all parts), Industrial-process control valves IEC 60695-11-10, Fire hazard testing Part 11-10: Test flames 50 W horizontal and vertical flame test methods IEC 60695-11-20, Fire

46、 hazard testing Part 11-20: Test flames 500 W Flame test methods IEC 60730-1:2010, Automatic electrical controls for household and similar use Part 1: General requirements IEC 60747 (all parts), Semiconductor devices Discrete devices I EC / T R 6 0 8 7 7, Procedures for ensuring the cleanliness of i

47、ndustrial-process measurement and control equipment in oxygen service IEC 60947-2, Low-voltage switchgear and controlgear Part 2: Circuit-breakers IEC 6 0 9 47- 3, Low-voltage switchgear and controlgear Part 3: Switches, disconnectors, switch-disconnectors and fuse-combination units IEC 60947-4-1, L

48、ow-voltage switchgear and controlgear Part 4-1: Contactors and motor-starters Electromechanical contactors and motor-starters IEC 60947-4-2, Low-voltage switchgear and controlgear Part 4-2: Contactors and motor-starters AC semiconductor motor controllers and starters IEC 60947-4-3, Low-voltage switc

49、hgear and controlgear Part 4-3: Contactors and motor-starters AC semiconductor controllers and contactors for non-motor loads IEC 60947-5-1, Low-voltage switchgear and controlgear Part 5-1: Control circuit devices and switching elements Electromechanical control circuit devices IEC 60947-5-2, Low-voltage switchgear and controlgear Part 5-2: Contr