IEEE C37 30 INT 1-2011 en Requirements for High-Voltage Switches《高压开关设备用IEEE Std C37 30 -1997标准要求的IEEE标准解释》.pdf

《IEEE C37 30 INT 1-2011 en Requirements for High-Voltage Switches《高压开关设备用IEEE Std C37 30 -1997标准要求的IEEE标准解释》.pdf》由会员分享，可在线阅读，更多相关《IEEE C37 30 INT 1-2011 en Requirements for High-Voltage Switches《高压开关设备用IEEE Std C37 30 -1997标准要求的IEEE标准解释》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、IEEE-SA - IEEE Std C37.30-1997IEEE Standards Interpretations for IEEE Std C37.30-1997 IEEE Standard Requirements for High-Voltage SwitchesCopyright 2011 by the Institute of Electrical and Electronics Engineers, Inc. 3 Park Avenue New York, New York 10016-5997 USA All Rights Reserved.This is an inter

2、pretation of IEEE Std C37.30-1997.Interpretations are issued to explain and clarify the intent of a standard and do not constitute an alteration to the original standard. In addition, interpretations are not intended to supply consulting information. Permission is hereby granted to download and prin

3、t one copy of this document. Individuals seeking permission to reproduce and/or distribute this document in its entirety or portions of this document must contact the IEEE Standards Department for the appropriate license. Use of the information contained in this document is at your own risk. IEEE St

4、andards Department Copyrights and Permissions 445 Hoes Lane, Piscataway, New Jersey 08855-1331, USAOctober 2011Interpretation Number: 1 Table 3 of IEEE Std C37.30-1992, Temperature Limitations for Air Switches, lists the temperature values in degrees-C for “(2) Conducting mechanical joints (b) Silve

5、r, silver alloy, or equivalent“ under columns 1, 2, and 4, to be 104, 53, 43 respectively. The same table in IEEE Std C37.30-1997 is Table 2, Temperature limitations for air switches, and lists the temperature values in degrees-C for “(b) Conducting mechanical joints (2) Silver, silver alloy, or equ

6、ivalent“ under columns 1, 2, and 4 as 125, 67, and 57 respectively.These temperature limits are associated with switch-part class designation FO6 for non-enclosed switches and TO6 for enclosed switches. The same table, Table 2, in IEEE Std C37.30-1997 lists other FO6 and TO6 components as having tem

7、perature limitations of 105, 53, and 43 respectively under columns 1, 2, and 4. Therefore, it appears that the temperature values in degrees-C listed in Table 2 of IEEE C37.30-1997 for “(b) Conducting mechanical joints (2) Silver, silver alloy, or equivalent“ under columns 1, 2, and 4 should be 105,

8、 53, and 43 respectively.Please provide the correct temperature values in degrees-C for Table 2 of IEEE C37.30-1997 for “(b) Conducting mechanical joints (2) Silver, silver alloy, or equivalent“ under columns 1, 2, and 4.Interpretation Response #1 http:/standards.ieee.org/findstds/interps/C37.30-199

9、7.html (1 of 2)11/4/2011 10:25:04 PMIEEE-SA - IEEE Std C37.30-1997The required behavior of this standard is dependent on the requirements of another Standard, IEEE Std C37.37-1996. The temperature rise limit changes made to Table 2 in IEEE Std C37.30-1997 render it erroneous, in that in each case th

10、e change does away with, and conflicts with, the loadability curves and equations (from IEEE Std C37.37-1996), and introduces conflict with the Switch-part class designation.The Temperature limitations in Table 1 of IEEE Std C37.37-1996 must be observed. Consultation on this matter was held with the

11、 members of the Working Group PC37.30.1. Responses were received from a majority of the Working Group and were unanimous in this position. The Working Group respondents include Manufacturers, Users and Consultants. The sponsors for IEEE Std C37.30-1997 and for IEEE Std C37.37-1996 are the same committee. Both standards are currently being combined into a consolidated standard PC37.30.1, expected to be completed by December 2010. This new standard will correct this conflict as stated.http:/standards.ieee.org/findstds/interps/C37.30-1997.html (2 of 2)11/4/2011 10:25:04 PM