IEEE C37 242-2013 en Guide for Synchronization Calibration Testing and Installation of Phasor Measurement Units (PMUs) for Power System Protection and Control《电.pdf

《IEEE C37 242-2013 en Guide for Synchronization Calibration Testing and Installation of Phasor Measurement Units (PMUs) for Power System Protection and Control《电.pdf》由会员分享，可在线阅读，更多相关《IEEE C37 242-2013 en Guide for Synchronization Calibration Testing and Installation of Phasor Measurement Units (PMUs) for Power System Protection and Control《电.pdf（107页珍藏版）》请在麦多课文档分享上搜索。

1、 IEEE Guide for Synchronization, Calibration, Testing, and Installation of Phasor Measurement Units (PMUs) for Power System Protection and Control Sponsored by the Power System Relaying Committee IEEE 3 Park Avenue New York, NY 10016-5997 USA 6 March 2013 IEEE Power and Energy Society IEEE Std C37.2

2、42-2013 IEEE Std C37.242-2013 IEEE Guide for Synchronization, Calibration, Testing, and Installation of Phasor Measurement Units (PMUs) for Power System Protection and Control Sponsor Power System Relaying Committee of the IEEE Power and Energy Society Approved 6 February 2013 IEEE-SA Standards Boar

3、d Abstract: Guidance for synchronization, calibration, testing, and installation of phasor measurement units (PMUs) applied in power systems is provided. The following are addressed in this guide: (a) Considerations for the installation of PMU devices based on application requirements and typical su

4、bstation electrical bus configurations; (b) Techniques focusing on the overall accuracy and availability of the time synchronization system; (c) Test and calibration procedures for PMUs for laboratory and field applications; (d) Communications testing for connecting PMUs to other devices including P

5、hasor Data Concentrators (PDCs). Keywords: calibration, GPS, IEEE C37.242, PMU, synchrophasor, testing The Institute of Electrical and Electronics Engineers, Inc. 3 Park Avenue, New York, NY 10016-5997, USA Copyright 2013 by The Institute of Electrical and Electronics Engineers, Inc. All rights rese

6、rved. Published 6 March 2013. Printed in the United States of America. IEEE is a registered trademark in the U.S. Patent +1 978 750 8400. Permission to photocopy portions of any individual standard for educational classroom use can also be obtained through the Copyright Clearance Center. Copyright 2

7、013 IEEE. All rights reserved. ivNotice to users Laws and regulations Users of IEEE Standards documents should consult all applicable laws and regulations. Compliance with the provisions of any IEEE Standards document does not imply compliance to any applicable regulatory requirements. Implementers

8、of the standard are responsible for observing or referring to the applicable regulatory requirements. IEEE does not, by the publication of its standards, intend to urge action that is not in compliance with applicable laws, and these documents may not be construed as doing so. Copyrights This docume

9、nt is copyrighted by the IEEE. It is made available for a wide variety of both public and private uses. These include both use, by reference, in laws and regulations, and use in private self-regulation, standardization, and the promotion of engineering practices and methods. By making this document

10、available for use and adoption by public authorities and private users, the IEEE does not waive any rights in copyright to this document. Updating of IEEE documents Users of IEEE Standards documents should be aware that these documents may be superseded at any time by the issuance of new editions or

11、 may be amended from time to time through the issuance of amendments, corrigenda, or errata. An official IEEE document at any point in time consists of the current edition of the document together with any amendments, corrigenda, or errata then in effect. In order to determine whether a given docume

12、nt is the current edition and whether it has been amended through the issuance of amendments, corrigenda, or errata, visit the IEEE-SA Website at http:/standards.ieee.org/index.html or contact the IEEE at the address listed previously. For more information about the IEEE Standards Association or the

13、 IEEE standards development process, visit IEEE-SA Website at http:/standards.ieee.org/index.html. Errata Errata, if any, for this and all other standards can be accessed at the following URL: http:/standards.ieee.org/findstds/errata/index.html. Users are encouraged to check this URL for errata peri

14、odically. Patents Attention is called to the possibility that implementation of this standard may require use of subject matter covered by patent rights. By publication of this standard, no position is taken by the IEEE with respect to the existence or validity of any patent rights in connection the

15、rewith. If a patent holder or patent applicant has filed a statement of assurance via an Accepted Letter of Assurance, then the statement is listed on the IEEE-SA Website at http:/standards.ieee.org/about/sasb/patcom/patents.html. Letters of Assurance may indicate whether the Submitter is willing or

16、 unwilling to grant licenses under patent rights without compensation or under reasonable rates, with reasonable terms and conditions that are demonstrably free of any unfair discrimination to applicants desiring to obtain such licenses. Copyright 2013 IEEE. All rights reserved. vEssential Patent Cl

17、aims may exist for which a Letter of Assurance has not been received. The IEEE is not responsible for identifying Essential Patent Claims for which a license may be required, for conducting inquiries into the legal validity or scope of Patents Claims, or determining whether any licensing terms or co

18、nditions provided in connection with submission of a Letter of Assurance, if any, or in any licensing agreements are reasonable or non-discriminatory. Users of this standard are expressly advised that determination of the validity of any patent rights, and the risk of infringement of such rights, is

19、 entirely their own responsibility. Further information may be obtained from the IEEE Standards Association. Copyright 2013 IEEE. All rights reserved. viParticipants At the time this IEEE guide was completed, the C5 Working Group had the following membership: Farnoosh Rahmatian, Chair Paul Myrda, Vi

20、ce Chair Mark Adamiak Galina Antonova Alexander Apostolov James Ariza Bill Dickerson Vasudev Gharpure Allen Goldstein James Hackett Yi Hu Mladen Kezunovic Harold Kirkham Vahid Madani Kenneth Martin A.P. (Sakis) Meliopoulos Jay Murphy Krish Narendra Damir Novosel Manu Parashar Mahendra Patel S. Richa

21、rds Veselin Skendzik Gerard Stenbakken A. Vaccaro Benton Vandiver The following members of the individual balloting committee voted on this guide. Balloters may have voted for approval, disapproval, or abstention. Mohamed Abdel Khalek William Ackerman Mark Adamiak Satish Aggarwal Ali Al Awazi Mihael

22、a Albu Saleman Alibhay Galina Antonova James Ariza David Bassett Martin Baur Philip Beaumont Kenneth Behrendt Robert Beresh Richard Bingham Gustavo Brunello Paul Cardinal Arvind K. Chaudhary Stephen Conrad Luis Coronado Andrew Dettloff Michael Dood Gary Engmann Dan Evans Ronald Farquharson Fredric F

23、riend Doaa Galal John Galanos Vasudev Gharpure David Gilmer Jalal Gohari Allen Goldstein Stephen Grier Randall C. Groves Erich Gunther James Hackett Donald Hall Dennis Hansen Roger Hedding Werner Hoelzl Yi Hu Gerald Johnson Innocent Kamwa Yuri Khersonsky Morteza Khodaie Harold Kirkham Joseph L. Koep

24、finger Jim Kulchisky Chung-Yiu Lam Raluca Lascu Greg Luri Vahid Madani Wayne Manges Kenneth Martin William McBride John McDonald William Moncrief Jay Murphy Jerry Murphy Bruce Muschlitz Michael S. Newman Damir Novosel James OBrien Lorraine Padden Donald Parker Bansi Patel Craig Preuss Iulian Profir

25、Farnoosh Rahmatian Reynaldo Ramos Michael Roberts Charles Rogers Thomas Rozek Sergio Santos Bartien Sayogo Thomas Schossig Devki Sharma Gil Shultz Veselin Skendzic James Smith Jerry Smith Aaron Snyder John Spare Gerard Stenbakken Gary Stoedter Charles Sufana Richard Taylor William Taylor John Tengdi

26、n Maria Tomica Eric Udren John Vergis Jane Verner Quintin Verzosa John Wang Solveig Ward Karl Weber Philip Winston Jian Yu Copyright 2013 IEEE. All rights reserved. viiWhen the IEEE-SA Standards Board approved this guide on 6 February 2013, it had the following membership: John Kulick, Chair Richard

27、 H. Hulett, Past Chair Konstantinos Karachalios, Secretary Masayuki Ariyoshi Peter Balma Farooq Bari Ted Burse Wael William Diab Stephen Dukes Jean-Philippe Faure Alexander Gelman Mark Halpin Gary Hoffman Paul Houz Jim Hughes Michael Janezic Joseph L. Koepfinger* David J. Law Oleg Logvinov Ron Peter

28、sen Gary Robinson Jon Walter Rosdahl Adrian Stephens Peter Sutherland Yatin Trivedi Phil Winston Yu Yuan *Member Emeritus Also included are the following nonvoting IEEE-SA Standards Board liaisons: Richard DeBlasio, DOE Representative Michael Janezic, NIST Representative Michelle Turner IEEE Standar

29、ds Program Manager, Document Development Matthew J. Ceglia IEEE Standards Program Manager, Technical Program Development Soo H. Kim Client Service Manager, Professional Services Copyright 2013 IEEE. All rights reserved. viiiIntroduction This introduction is not part of IEEE Std C37.242-2013, IEEE Gu

30、ide for Synchronization, Calibration, Testing, and Installation of Phasor Measurement Units (PMUs) for Power System Protection and Control. Use of synchrophasor technology in the electric power industry is rapidly growing, moving from research and pilot projects into system-wide production level dep

31、loyment. Accordingly, a practical guide for installing and testing phasor measurement units (PMUs) is expected to be very beneficial to field practitioners, sharing and leveraging the early experience that the pioneers in this area have accumulated. This document was developed by IEEE PES Power Syst

32、em Relaying Committee to guide and educate various professionals interested in deploying PMUs and using the associated synchrophasor data. Copyright 2013 IEEE. All rights reserved. ixContents 1. Overview 1 1.1 Scope . 1 1.2 Purpose 2 2. Normative references 2 3. Definitions, special terms, acronyms,

33、 and abbreviations 2 3.1 Definitions . 3 3.2 Special terms 3 3.3 Acronyms and abbreviations . 3 4. Synchronization techniques, accuracy, and availability . 4 4.1 Introduction . 4 4.2 Role of time synchronization in PMUs 4 4.3 Satellite-based synchronizing sources . 5 4.4 Terrestrial systems. 9 4.5 S

34、ynchronization distribution methods . 10 5. Synchrophasor measurement accuracy characterization 10 5.1 Introduction . 10 5.2 Data accuracy characterization 11 5.3 Data accuracy 12 5.4 Characterization of instrumentation channels 13 5.5 Characterization of GPS-synchronized measurement devices (PMUs).

35、 14 5.6 GPS-synchronized equipment reliability . 14 6. PMU installation, commissioning, and maintenance 15 6.1 Preface . 15 6.2 Overview . 15 6.3 Pre-installation procedures 16 6.4 Analog and digital input 20 6.5 Power input 21 6.6 Communications 21 6.7 Summary of design considerations 24 6.8 Pre-in

36、stallation tests. 25 6.9 Verification of end-to-end calibration . 25 6.10 Communications operation 28 6.11 Record keeping 29 7. Testing and calibration . 29 7.1 Overview . 29 7.2 Objective of testing 29 7.3 Types of tests. 30 7.4 Test equipment 34 7.5 Methods for performing the tests. 40 7.6 Synchro

37、phasor message format . 54 7.7 Final comments 55 Annex A (informative) Bibliography . 56 Annex B (informative) Responses of the reference signal processing model to test signals 60 Copyright 2013 IEEE. All rights reserved. xAnnex C (informative) Effects of signal channels 80 Annex D (informative) Ex

38、amples of instrumentation channel impact on accuracy using approximate models 85 Annex E (informative) Example of commissioning tests and measurements. 95 Copyright 2013 IEEE. All rights reserved. 1IEEE Guide for Synchronization, Calibration, Testing, and Installation of Phasor Measurement Units (PM

39、Us) for Power System Protection and Control IMPORTANT NOTICE: IEEE Standards documents are not intended to ensure safety, health, or environmental protection, or ensure against interference with or from other devices or networks. Implementers of IEEE Standards documents are responsible for determini

40、ng and complying with all appropriate safety, security, environmental, health, and interference protection practices and all applicable laws and regulations. This IEEE document is made available for use subject to important notices and legal disclaimers. These notices and disclaimers appear in all p

41、ublications containing this document and may be found under the heading “Important Notice” or “Important Notices and Disclaimers Concerning IEEE Documents.” They can also be obtained on request from IEEE or viewed at http:/standards.ieee.org/IPR/disclaimers.html. 1. Overview 1.1 Scope The document p

42、rovides guidance for synchronization, calibration, testing, and installation of phasor measurement units (PMUs) applied in power system protection and control. The following are addressed in this guide: a) Considerations for the installation of PMU devices based on application requirements and typic

43、al bus configurations. b) Techniques focusing on the overall accuracy and availability of the time synchronization system. c) Test and calibration procedures for PMUs for laboratory and field applications. d) Communications testing for connecting PMUs to other devices including Phasor Data Concentra

44、tors (PDCs). IEEE Std C37.242-2013 IEEE Guide for Synchronization, Calibration, Testing, and Installation of Phasor Measurement Units (PMUs) for Power System Protection and Control Copyright 2013 IEEE. All rights reserved. 21.2 Purpose This guide is intended to be used by power system protection pro

45、fessionals for PMU installation and covers the requirements for synchronization of field devices and connection to other devices including PDCs. 2. Normative references The following referenced documents are indispensable for the application of this document (i.e., they must be understood and used,

46、so each referenced document is cited in text and its relationship to this document is explained). For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments or corrigenda) applies. IEC 61850-3, Communication N

47、etworks and Systems in SubstationsPart 3: General Requirements.1IEC/TR 61850-90-5, Ed. 1.0, Communication networks and systems for power utility automation Part 90-5: Use of IEC 61850 to transmit synchrophasor information according to IEEE C37.118. IEEE Std 1588-2008, IEEE Standard for a Precision C

48、lock Synchronization Protocol for Networked Measurement and Control Systems.2,3IEEE Std C37.118-2005, IEEE Standard for Synchrophasors for Power Systems. IEEE Std C37.118.1-2011, IEEE Standard for Synchrophasor Measurements for Power Systems. IEEE Std C37.118.2-2011, IEEE Standard for Synchrophasor

49、Data Transfer for Power Systems. IEEE Std C37.233-2009, IEEE Guide for Power System Protection Testing. IEEE Std C37.238-2011, IEEE Standard Profile for Use of IEEE 1588 Precision Time Protocol in Power System Applications. IEEE Std C57.13, IEEE Standard Requirements for Instrument Transformers. IRIG Standard 200-04 (2004), IRIG Serial Time Code Formats, Telecommunications and Timing Group, Range Commanders Council, U.S. Army White Sands Missile Range, NM, USA.43. Definitions, special terms, acronyms, and abbreviations These definitions, acronyms, a