IEC 62364-2013 Hydraulic machines - Guide for dealing with hydro-abrasive erosion in Kaplan Francis and Pelton turbines《液压机.卡普兰、弗朗西斯、水斗式涡轮机水冲蚀处理指南》.pdf

《IEC 62364-2013 Hydraulic machines - Guide for dealing with hydro-abrasive erosion in Kaplan Francis and Pelton turbines《液压机.卡普兰、弗朗西斯、水斗式涡轮机水冲蚀处理指南》.pdf》由会员分享，可在线阅读，更多相关《IEC 62364-2013 Hydraulic machines - Guide for dealing with hydro-abrasive erosion in Kaplan Francis and Pelton turbines《液压机.卡普兰、弗朗西斯、水斗式涡轮机水冲蚀处理指南》.pdf（156页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 62364 Edition 1.0 2013-06 INTERNATIONAL STANDARD NORME INTERNATIONALE Hydraulic machines Guide for dealing with hydro-abrasive erosion in Kaplan, Francis, and Pelton turbines Machines hydrauliques Guide relatif au traitement de lrosion hydro-abrasive des turbines Kaplan, Francis et Pelton IEC62

2、364:2013 colourinsideTHIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2013 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm,

3、 without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National

4、 Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit

5、de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Cent

6、ral Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, el

7、ectronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Useful links: IEC publications search - www.iec.ch/

8、searchpub The advanced search enables you to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC pu

9、blications. Just Published details all new publications released. Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, wit

10、h equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec

11、.ch. A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des pu

12、blications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub La recherche avance vous permet de trouver des publications CEI en utilisant d

13、iffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications de la CEI. Just Published dtaille les nouvelles publi

14、cations parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans

15、 les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 62364 Edition 1.0 2013-06 INTER

16、NATIONAL STANDARD NORME INTERNATIONALE Hydraulic machines Guide for dealing with hydro-abrasive erosion in Kaplan, Francis, and Pelton turbines Machines hydrauliques Guide relatif au traitement de lrosion hydro-abrasive des turbines Kaplan, Francis et Pelton INTERNATIONAL ELECTROTECHNICAL COMMISSION

17、 COMMISSION ELECTROTECHNIQUE INTERNATIONALE XC ICS 23.100.10; 27.140 PRICE CODE CODE PRIX ISBN 978-2-83220-829-8 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication f

18、rom an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. colourinside 2 62364 IEC:2013 CONTENTS FOREWORD . 5 INTRODUCTION . 7 1 Scope . 8 2 Terms, definitions and symbols 8 Units . 8 2.1Terms, definitions and symbols . 9 2.23 Abr

19、asion rate 11 Theoretical model 11 3.1Introduction to the PL variable . 13 3.2Survey results . 15 3.3Reference model . 16 3.44 Design 17 General . 17 4.1Water conveyance system . 17 4.2Valve . 18 4.3General . 18 4.3.1Selection of abrasion resistant materials and coating 18 4.3.2Stainless steel overl

20、ays . 19 4.3.3Protection (closing) of the gap between housing and trunnion . 19 4.3.4Stops located outside the valve . 19 4.3.5Proper capacity of inlet valve operator . 19 4.3.6Increase bypass size to allow higher guide vane leakage 19 4.3.7Bypass system design . 20 4.3.8Turbine 20 4.4General . 20 4

21、.4.1Hydraulic design 20 4.4.2Mechanical design . 22 4.4.3Operation 28 4.4.4Spares and regular inspections . 29 4.4.5Particle sampling and monitoring . 29 4.4.65 Abrasion resistant materials . 30 Guidelines concerning relative abrasion resistance of materials including 5.1abrasion resistant coatings

22、30 General . 30 5.1.1Discussion and conclusions . 31 5.1.2Guidelines concerning maintainability of abrasion resistant coating materials 32 5.2Definition of terms used in this sublcause 32 5.2.1Time between overhaul for protective coatings 32 5.2.2Maintenance of protective coatings 33 5.2.36 Guidelin

23、es on insertions into specifications 34 General . 34 6.1Properties of particles going through the turbine 35 6.2Size distribution of particles 35 6.3Mineral composition of particles for each of the above mentioned periods . 36 6.4Annex A (informative) PL calculation example 37 Annex B (informative)

24、Measuring and recording abrasion damages . 39 62364 IEC:2013 3 Annex C (informative) Water sampling procedure 52 Annex D (informative) Procedures for analysis of particle concentration, size, hardness and shape . 53 Annex E (informative) Tests of abrasion resistant materials . 56 Annex F (informativ

25、e) Typical criteria to determine overhaul time due to abrasion erosion . 67 Annex G (informative) Example to calculate the amount of erosion in the full model 68 Annex H (informative) Examples to calculate the TBO in the reference model 70 Bibliography 73 Figure 1 Estimation of the characteristic ve

26、locities in guide vanes, Wgv, and runner, Wrun, as a function of turbine specific speed 13 Figure 2 Example of flow pattern in a Pelton injector at different load 14 Figure 3 Example of protection of transition area . 19 Figure 4 Runner blade overhang in refurbishment project 21 Figure 5 Example of

27、“mouse-ear” cavitation on runner band 22 Figure 6 Detailed design of guide vane trunnion seals . 23 Figure 7 Example of fixing of facing plates from the dry side 25 Figure 8 Head cover balancing pipes with bends 26 Figure 9 Step labyrinth with optimized shape for hard coating 28 Figure 10 Developmen

28、t of spiral pressure over time . 33 Figure D.1 Typical examples of particle geometry 55 Figure E.1 Schematic of test rig used for test 1 56 Figure E.2 ASTM test apparatus 58 Figure E.3 Test coupon 59 Figure E.4 Slurry pot test facility 60 Figure E.5 High velocity test rig . 61 Figure E.6 Samples are

29、 located on the rotating disk 62 Figure E.7 Comparison of two samples after testing . 62 Figure E.8 Whole test system of rotating disk 62 Figure E.9 Schematic of test rig used for test 8 64 Figure E.10 Testing of samples on hydro abrasive stand . 65 Figure E.11 Cover of disc 65 Figure E.12 Curve of

30、unit abrasion rate with circumference velocity for 3 kinds of materials . 66 Table 1 Data analysis of the supplied questionnaire . 16 Table 2 Overview over the feasibility for repair C . 33 Table 3 Form for properties of particles going through the turbine 35 Table 4 Form for size distribution of pa

31、rticles . 36 Table 5 Form for mineral composition of particles for each of the above mentioned periods . 36 Table A.1 Example of documenting sample tests . 37 Table A.2 Example of documenting sample results 38 Table B.1 Inspection record, runner blade inlet form 44 4 62364 IEC:2013 Table B.2 Inspect

32、ion record, runner blade outlet form 45 Table B.3 Inspection record, runner band form. 46 Table B.4 Inspection record, guide vanes form. 47 Table B.5 Inspection record, facing plates and covers form 48 Table B.6 Inspection record, upper stationary seal form . 49 Table B.7 Inspection record, upper ro

33、tating seal form 49 Table B.8 Inspection record, lower stationary seal form . 50 Table B.9 Inspection record, lower rotating seal form . 51 Table E.1 Relative wear resistance in laboratory test 1 57 Table E.2 Relative wear resistance in laboratory test 2 57 Table E.3 Relative wear resistance in labo

34、ratory test 3 58 Table E.4 Relative wear resistance in test 4 . 59 Table E.5 Results of test 60 Table E.6 Results of test 61 Table E.7 Results from test 63 Table E.8 Relative wear resistance in laboratory test 8 64 Table E.9 Results of relative wear resistance for some materials (U = 40m/s) 66 Table

35、 G.1 Calculations . 69 Table H.1 Pelton turbine calculation example . 70 Table H.2 Francis turbine calculation example . 71 62364 IEC:2013 5 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ HYDRAULIC MACHINES GUIDE FOR DEALING WITH HYDRO-ABRASIVE EROSION IN KAPLAN, FRANCIS, AND PELTON TURBINES FOREWORD 1

36、) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrica

37、l and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technica

38、l committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organizat

39、ion for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical com

40、mittee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications

41、is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and

42、 regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services an

43、d, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or

44、 agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use

45、 of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that s

46、ome of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 62364 has been prepared by IEC technical committee 4: Hydraulic turbines. The text of this standard is based on

47、 the following documents: FDIS Report on voting 4/279/FDIS 4/283/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. 6 62364 IEC:20

48、13 The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a r

49、evised edition, or amended. IMPORTANT The colour inside logo on the cover page of this publication indicates that it contains colours which are considered to be useful for the correct understanding of its contents. Users should therefore print this document using a colour printer. 62364 IEC:2013 7 INTRODUCTION Many owners of hydroelectric plants co