UL 330B-2015 UL Standard for Safety Hose and Hose Assemblies for Use With Dispensing Devices Dispensing Diesel Fuel Biodiesel Fuel Diesel Biodiesel Blends With Nominal Biodiesel Co.pdf

《UL 330B-2015 UL Standard for Safety Hose and Hose Assemblies for Use With Dispensing Devices Dispensing Diesel Fuel Biodiesel Fuel Diesel Biodiesel Blends With Nominal Biodiesel Co.pdf》由会员分享，可在线阅读，更多相关《UL 330B-2015 UL Standard for Safety Hose and Hose Assemblies for Use With Dispensing Devices Dispensing Diesel Fuel Biodiesel Fuel Diesel Biodiesel Blends With Nominal Biodiesel Co.pdf（44页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 330B Hose and Hose Assemblies for Use With Dispensing Devices Dispensing Diesel Fuel, Biodiesel Fuel, Diesel/Biodiesel Blends With Nominal Biodiesel Concentrations Up To 20 Percent (B20), Ke

2、rosene, and Fuel OilUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Hose and Hose Assemblies for Use With Di

3、spensing Devices Dispensing Diesel Fuel, Biodiesel Fuel, Diesel/Biodiesel Blends With Nominal Biodiesel Concentrations Up To 20 Percent (B20), Kerosene, and Fuel Oil, UL 330B First Edition, Dated December 18, 2015 SUMMARY OF TOPICS The following Standard has been published: 1. Standard for Safety fo

4、r Hose and Hose Assemblies for Use With Dispensing Devices Dispensing Diesel Fuel, Biodiesel Fuel, Diesel/Biodiesel Blends With Nominal Biodiesel Concentrations Up To 20 Percent (B20), Kerosene, and Fuel Oil, UL 330B The new requirements are substantially in accordance with Proposal(s) on this subje

5、ct dated July 10, 2015. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwise without prior permission of UL. UL provides this Standard as is without warr

6、anty of any kind, either expressed or implied, including but not limited to, the implied warranties of merchantability or tness for any purpose. In no event will UL be liable for any special, incidental, consequential, indirect or similar damages, including loss of prots, lost savings, loss of data,

7、 or any other damages arising out of the use of or the inability to use this Standard, even if UL or an authorized UL representative has been advised of the possibility of such damage. In no event shall ULs liability for any damage ever exceed the price paid for this Standard, regardless of the form

8、 of the claim. Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, expense, liability, damage, claim, or judgment (including reasonable attorneys fees) resulting from any error or deviation introduced while purchase

9、r is storing an electronic Standard on the purchasers computer system. The requirements in this Standard are now in effect, except for those paragraphs, sections, tables, gures, and/or other elements of the Standard having future effective dates as indicated in the note following the affected item.

10、The prior text for requirements that have been revised and that have a future effective date are located after the Standard, and are preceded by a SUPERSEDED REQUIREMENTS notice. DECEMBER 18, 2015 UL 330B tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERM

11、ISSION FROM UL DECEMBER 18, 2015 UL 330B tr2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL December 18, 2015 1 UL 330B Standard for Hose and Hose Assemblies for Use With Dispensing Devices Dispensing Diesel Fuel, Biodie

12、sel Fuel, Diesel/Biodiesel Blends With Nominal Biodiesel Concentrations Up To 20 Percent (B20), Kerosene, and Fuel Oil First Edition December 18, 2015 This ANSI/UL Standard for Safety consists of the First Edition. The most recent designation of ANSI/UL 330B as an American National Standard (ANSI) o

13、ccurred on December 17, 2015. ANSI approval for a standard does not include the Cover Page, Transmittal Pages, Title Page, or effective date information. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be submitted via a Proposal R

14、equest in ULs On-Line Collaborative Standards Development System (CSDS) at http:/. ULs Standards for Safety are copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any way. All of ULs Standards and all copyrights, ownerships, and rights regarding those Standar

15、ds shall remain the sole and exclusive property of UL. COPYRIGHT 2015 UNDERWRITERS LABORATORIES INC. ANSI/UL 330B-2015UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL DECEMBER 18, 2015 UL 330B 2 No Text on This PageUL COPYRIGHTED MATERIAL NOT

16、 AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS INTRODUCTION 1 Scope .6 2 General 7 2.1 Units of Measurement .7 2.2 Undated References 7 3 Glossary .7 CONSTRUCTION 4 Tube and Cover 8 5 Thickness of Cover 8 6 Internal Diameter .9 7 Reinforcement 9 8 Electrical

17、 Bonding .9 9 Couplings 9 10 Materials .10 10.1 Metallic materials .10 10.2 Nonmetallic materials .11 PERFORMANCE 11 General 14 12 Repeating Bending Test (Empty) .15 12.1 General .15 12.2 Sample .15 12.3 Apparatus .15 12.4 Method .15 13 Hydrostatic Strength Test .17 13.1 General .17 13.2 Sample .17

18、13.3 Apparatus .17 13.4 Method .17 14 Repeated Bending Test (Filled) .18 14.1 General .18 14.2 Sample .18 14.3 Apparatus .18 14.4 Method .19 15 Permeation Test (For Low Permeation Hose) 19 15.1 General .19 15.2 Test equipment 19 15.3 General test procedure and instructions .20 15.4 Samples 21 15.5 P

19、retest procedure 21 15.6 Preconditioning procedure .22 15.7 Permeation test procedure 22 15.8 Steady state criteria 23 16 Electrical Resistance Tests for Hose Having Nonmetallic Electrically Conductive Materials . .24 16.1 General .24 16.2 Samples 24 DECEMBER 18, 2015 UL 330B 3UL COPYRIGHTED MATERIA

20、L NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 16.3 Apparatus .24 16.4 Method .24 17 Leakage and Electrical Continuity Test 25 17.1 General .25 17.2 Sample .25 17.3 Apparatus .25 17.4 Method .25 18 Swivel Joint Operation Test 26 18.1 General .26 19 Pull Test .26

21、 19.1 General .26 19.2 Sample .26 19.3 Equipment .26 19.4 Method .26 20 Adhesion Test 27 20.1 General .27 20.2 Sample .27 20.3 Apparatus .27 20.4 Method .27 21 Deformation Test .28 22 Kink Test 28 23 Tensile Strength and Elongation Tests for Hose Components 28 23.1 General .28 23.2 Samples 29 23.3 A

22、pparatus .29 23.4 Method .29 24 Accelerated Air Oven Aging Test for Hose Components .30 24.1 General .30 24.2 Samples 30 24.3 Apparatus .30 24.4 Method .31 25 Ozone Exposure Test .31 25.1 General .31 25.2 Samples 31 25.3 Apparatus .31 25.4 Method .31 26 Immersion Tests for Hose Components .32 26.1 T

23、ensile strength and ultimate elongation 32 26.2 Volume change 33 27 Low Temperature Test 34 27.1 General .34 27.2 Sample .34 27.3 Apparatus .34 27.4 Method .34 28 Long Term Exposure Test for Hose and Hose Assemblies .35 28.1 General .35 28.2 Samples 35 28.3 Method .36 29 Bending Test for Hose Assemb

24、lies with Internal Spring 36 MANUFACTURING AND PRODUCTION TESTS 30 General 37 DECEMBER 18, 2015 UL 330B 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL MARKING 31 Details .37 SUPPLEMENT SA - TEST FLUIDS SA.1 Representative Aggressive Combus

25、tible Test Fuel Mixtures SA1 DECEMBER 18, 2015 UL 330B 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL INTRODUCTION 1 Scope 1.1 These requirements cover hose and hose assemblies for use on dispensing devices for fuels. A ammable liquid hose

26、 assembly consists of exible hose and ttings suitable for attachment to fuel dispensing equipment. Fuels, as dened by these requirements, include one or more of the fuels described in 1.2. 1.2 Hose and hose assemblies covered by these requirements are intended for use with one or more of the followi

27、ng fuels: a) Diesel fuel and diesel fuel/biodiesel blends with nominal biodiesel concentrations up to 5 percent (B0 B5) formulated in accordance with the Standard Specication for Diesel Fuel Oils, ASTM D975. b) Diesel/biodiesel blends with nominal biodiesel concentrations from 5 percent up to 20 per

28、cent (B6 B20) formulated in accordance with the Standard Specication for Diesel Fuel Oil, Biodiesel Blends (B6 B20), ASTM D7467. c) Biodiesel (B99.9/B100) formulated in accordance with the Standard Specication for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels, ASTM D6751. d) Kerosene

29、 formulated in accordance with the Standard Specication for Kerosine, ASTM D3699. e) Fuel Oil (heating oil) formulated in accordance with the Standard Specication for Fuel Oils, ASTM D396. 1.3 Hose assemblies are intended for use in accordance with the Code for Motor Fuel Dispensing Facilities and R

30、epair Garages, NFPA 30A. 1.4 These requirements cover hose and hose assemblies (hose with couplings attached) in sizes up to and including 1-1/2 inches (38.1 mm). 1.5 Hose for conveying liquid fuel is intended for use at a maximum working pressure of 50 psig (345 kPa). 1.6 These requirements cover h

31、ose and hose assemblies for use at temperatures down to minus 40C (minus 40F) or optionally down to minus 54C (minus 65F). 1.7 These requirements do not cover hose or hose assemblies, intended for use in automotive vehicles or in conned areas, except for locations inside the housings of dispensing d

32、evices complying with the Outline for Power-Operated Dispensing Devices for Diesel Fuel, Biodiesel Fuel, Diesel/Biodiesel Blends with Nominal Biodiesel Concentrations Up to 20 Percent (B20), Kerosene, and Fuel Oil, UL 87B. DECEMBER 18, 2015 UL 330B 6UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER

33、 REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 1.8 These requirements do not cover hoses or hose assemblies for use with any other fuel other than as described in 1.2. 2 General 2.1 Units of Measurement 2.1.1 When a value for measurement is followed by a value in other units in parentheses

34、, the rst stated value is the requirement. 2.2 Undated References 2.2.1 Any undated reference to a code or standard appearing in the requirements of this Outline shall be interpreted as referring to the latest edition of that code or standard. 3 Glossary 3.1 For the purposes of this outline, the fol

35、lowing denitions apply. 3.2 DISPENSING DEVICE A product consisting of various components that is used to control and meter the ow of liquid from an upstream storage device. 3.3 PERMEATION SURFACE AREA The length of the hose as determined in 15.5.4 multiplied by the inner circumference of the hose, e

36、xpressed in square meters. For vacuum-assist vapor recovery hose, the length of the hose is multiplied by the inner circumference of the outer hose. For balance vapor recovery hose, the length of the hose is multiplied by the average inner circumference of the outer hose. 3.4 REINFORCEMENT Natural o

37、r synthetic bers or fabric, or metallic wire that is wrapped, braided or spiral wound in one or more layers over the tube, intended to provide longitudinal and transverse (hoop) strength to the hose. 3.5 SEAL, DYNAMIC A seal that is subject to mechanical movement or other applied forces that result

38、in movement or exing of the seal under normal use conditions. 3.6 SEAL, STATIC A seal that is not subject to mechanical movement or other applied forces other than compressing forces that are applied during installation and maintained during normal use conditions. DECEMBER 18, 2015 UL 330B 7UL COPYR

39、IGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONSTRUCTION 4 Tube and Cover 4.1 The tube shall be made from a material resistant to the fuels anticipated by these requirements. 4.2 The cover shall be made from a material resistant to the fuels ant

40、icipated by these requirements and ozone. 4.3 The tube and cover shall be of uniform thickness, and free from pitting, blisters, or other imperfections. This requirement is not intended to exclude the use of a corrugated cover. 5 Thickness of Cover 5.1 The thickness of the cover shall not be less th

41、an 0.047 inch (1.19 mm) when measured in accordance with 5.2 5.6. 5.2 For removing irregularities in samples, the buffing machine or skiving machine outlined in the Standard Practice for Rubber Preparation of Product Pieces for Test Purposes from Products, ASTM D3183, is to be used. 5.3 The abrasive

42、 wheel of the buffing machine is to be No. 30 60 grit and the diameter and rotary velocity of the wheel are to be such that it will have a peripheral speed of 4000 700 feet per minute (20.3 3.6 m/s). The machine is to be provided with a slow feed so that very little compound can be removed at one cu

43、t to avoid overheating of the specimen. 5.4 A dial micrometer graduated to 0.001 inch (0.03 mm) that exerts a load of 2.82 3.00 ounces (80 85 grams) by means of a weight is to be used to measure thickness. he load is to be applied through a at contact foot 0.25 0.01 inch (6.4 0.3 mm) in diameter. 5.

44、5 To determine the thickness of the tube and cover, a strip,68inches (152.4 203.2 mm) long and 1 inch (25.4 mm) wide, or as close to 1 inch (25.4 mm) as possible from small diameter hose, is to be cut longitudinally from the hose, and the part separated from the plies. When the thickness of the part

45、 is not uniform around the circumference of the hose, the strip is to be cut from the thinnest portion of the sample. 5.6 The strip specimen is to be buffed or skived to remove the impressions left by the fabric or braid or other surface irregularities, using the equipment described in 5.2 and 5.3.

46、A series of ve thickness measurements are to be taken within the area from which the impressions have been removed, and the maximum reading obtained is to be taken as the thickness of the part. DECEMBER 18, 2015 UL 330B 8UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION

47、 WITHOUT PERMISSION FROM UL 6 Internal Diameter 6.1 The internal diameter of a hose shall be equal to the nominal diameter 1/32 inch (0.8 mm) for sizes up to and including 3/4 inch (19.0 mm) and 1/16 inch (1.6 mm) for larger sizes. 6.2 A tapered plug gauge of wood or metal having a taper of 3/8 inch

48、 per foot (31.3 mm/m), marked to indicate variations of 1/64 inch (0.4 mm) in diameter, or a set of wood or metal plug gauges, straight or ball type, in increments no greater than 0.01 inches (0.25 mm) for hoses in sizes 1 inch (25.4 mm) and less and 0.02 inches (0.51 mm) for hoses in sizes greater

49、than 1 inch (25.4 mm), shall be used for measuring the internal diameter. An expanding ball gauge, and a micrometer or other equivalent means to accurately measure the expanded ball, are required in some cases. 6.3 The end of the hose is to be cut square. When a tapered plug gauge is used, the plug gauge is to be inserted in the hose sample until a close t is obtained without forcing. The diameter of the gauge at the end of the sample, to the nearest 1/64 inch (0.4 mm), is