SSPC PS 1 10-1982 Four-Coat Oil Base Zinc Oxide Painting System (Without Lead or Chromate Pigment) (Editorial Revisions November 1 2004)《四层油基氧化锌涂料系统(无铅颜料或铬酸盐颜料) 编辑修订 2004年11月1日》.pdf

《SSPC PS 1 10-1982 Four-Coat Oil Base Zinc Oxide Painting System (Without Lead or Chromate Pigment) (Editorial Revisions November 1 2004)《四层油基氧化锌涂料系统(无铅颜料或铬酸盐颜料) 编辑修订 2004年11月1日》.pdf》由会员分享，可在线阅读，更多相关《SSPC PS 1 10-1982 Four-Coat Oil Base Zinc Oxide Painting System (Without Lead or Chromate Pigment) (Editorial Revisions November 1 2004)《四层油基氧化锌涂料系统(无铅颜料或铬酸盐颜料) 编辑修订 2004年11月1日》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、5-19SSPC-PS 1.10November 1, 1982Editorial Revisions November 1, 2004SSPC: The Society for Protective CoatingsPAINTING SYSTEM NO. 1.10Four-Coat Oil Base Zinc Oxide Painting System(Without Lead or Chromate Pigment)1. Scope1.1 This specifi cation covers an oil base, lead- and chromate-free painting sys

2、tem for steel cleaned with hand or power tools.1.2 This system is suitable for use on parts or structures exposed in Environmental Zone 1A (interior, normally dry) and Zone 1 B (exterior, normally dry).1.3 The fi nish paint allows for a choice of durable, fade-resistant colors.2. Description2.1 This

3、 painting system consists of surface preparation by solvent cleaning and hand or power tool cleaning, two coats of zinc oxide linseed oil/alkyd primer, and two coats of alkyd white or tinted fi nish coat.3. Referenced Standards3.1 The latest issue, revision, or amendment of the refer-enced standards

4、 in effect on the date of invitation to bid shall govern, unless otherwise specifi ed. Standards marked with an asterisk (*) are referenced only in the Notes, which are not requirements of this specifi cation.3.2 If there is a confl ict between the requirements of any of the cited referenced standar

5、ds and this specifi cation, the requirements of this specifi cation shall prevail.3.3 SSPC STANDARDS AND JOINT STANDARDS:PA 1 Shop, Field, and Maintenance Painting of SteelPA 2 Measurement of Dry Coating Thickness With Magnetic GagesPA Guide 4 Guide to Maintenance Re-painting with Oil Base or Alkyd

6、Painting SystemsPaint 25 Red Iron Oxide, Zinc Oxide, Raw Lin seed Oil, and Alkyd PrimerPaint 101 Aluminum Alkyd PaintPaint 104 White or Tinted Alkyd PaintPaint 108 High-Build Thixotropic Leafi ng Aluminum PaintSP 2 Hand Tool CleaningSP 3 Power Tool CleaningSP 5/NACE No. 1 White Metal Blast CleaningS

7、P 6/NACE No. 3 Commercial Blast CleaningSP 7/NACE No. 4 Brush-Off Blast CleaningSP 8 PicklingSP 10/NACE No. 2 Near-White Blast Cleaning3.4 AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) STANDARD:D 3925 Standard Practice for Sampling Liquid Paints and Related Pigmented Coatings4. Surface Preparati

8、on4.1 SSPC-SP 2, “Hand Tool Cleaning,” or SSPC-SP 3, “Power Tool Cleaning.” If specifi ed in the procurement docu-ments, blast cleaning or pickling shall be substituted (SSPC-SP 5, 6, 7, 8, or 10).5. Paints5.1 PRIMER: SSPC-Paint 25, “Red Iron Oxide, Zinc Oxide, Raw Linseed Oil and Alkyd Primer.”5.2

9、SECOND COAT: SSPC-Paint 25, “Red Iron Oxide, Zinc Oxide, Raw Linseed Oil and Alkyd Primer” tinted with carbon black or lampblack dispersion to a color contrasting with that of the primer.5.3 THIRD COAT: SSPC-Paint 104, “White or Tinted Alkyd Paint,” tinted with carbon black or lampblack dispersion t

10、o a color contrasting with that of the fi nish paint.5.4 FINISH COAT: SSPC-Paint 104, “White or Tinted Alkyd Paint.” The color must be specifi ed.5.5 ALTERNATIVE FINISH COAT: If specifi ed in the procurement documents, a fi nish coat complying with specifi -cation SSPC-Paint 101, “Aluminum Alkyd Pai

11、nt, Leafi ng (Type I),” shall be applied in place of the standard fi nish coat. If this alternative fi nish coat is used, then the intermediate coat shall consist of one coat of SSPC-Paint 101, “Alkyd Aluminum Paint, Non-Leafi ng (Type II).”5.6 ALTERNATIVE FINISH COAT: If specifi ed in the procureme

12、nt documents, a fi nish coat complying with 5-20SSPC-PS 1.10November 1, 1982Editorial Revisions November 1, 2004specifi cation SSPC-Paint 108, “High-Build Thixotropic Leaf-ing Aluminum Paint,” shall be applied in place of the standard fi nish coat. If this alternative fi nish coat is used, then no t

13、hird coat shall be required, but the dry fi lm thickness shall not be less than 64 micrometers (2.5 mils) for the fi nish coat and 150 micrometers (6.0 mils) for the painting system.6. Paint Application6.1 PAINT APPLICATION: Follow requirements of SSPC-PA 1, “Shop, Field, and Maintenance Painting of

14、 Steel.”6.2 TOUCH-UP PAINTING: In accordance with specifi ca-tion SSPC-PA 1, “Shop, Field, and Maintenance Painting of Steel” and in particular with the Section thereof entitled “Field Painting.”6.3 MAINTENANCE PAINTING: The provisions of SSPC-PA Guide 4, “Guide to Maintenance Repainting with Oil Ba

15、se or Alkyd Painting Systems” should be followed.6.4 NUMBER OF COATS: Minimum of four.6.5 DRY FILM THICKNESS OF PAINT SYSTEM: Not less than the following as measured in accordance with SSPC-PA 2, “Measurement of Dry Coating Thickness with Magnetic Gages”: primer 50 micrometers (2.0 mils); for the fo

16、ur coat painting system 150 micrometers (6.0 mils). If alternative fi nish coat is used as indicated in Section 5.6, see that section for dry fi lm thickness requirements.7. Inspection7.1 All work and materials supplied under this specifi ca-tion are subject to timely inspection by the purchaser or

17、his authorized representative. The contractor shall correct such work or replace such material as is found defective under this specifi cation (See Note 9.1.). In case of dispute, unless otherwise specifi ed, the arbitration or settlement procedure established in the procurement documents shall be f

18、ollowed. If no arbitration or settlement procedure is established, then a procedure mutually agreeable to purchaser, material supplier, and contractor shall be used.7.2 Samples of paints under this painting system may be requested by the purchaser and shall be supplied upon request along with the ma

19、nufacturers name and identifi cation for the materials. Samples may be requested at the time the purchase order is placed, or may be taken from unopened containers at the job site.7.3 Unless otherwise specifi ed, the sampling shall be in accordance with ASTM D 3925.8. Disclaimer8.1 While every preca

20、ution is taken to ensure that all information furnished in SSPC standards and specifi cations is as accurate, complete, and useful as possible, SSPC cannot assume responsibility nor incur any obligation resulting from the use of any materials, coatings, or methods specifi ed herein, or of the specif

21、i cation or standard itself.8.2 This specifi cation does not attempt to address problems concerning safety associated with its use. The user of this specifi cation, as well as the user of all products or practices described herein, is responsible for instituting appropriate health and safety practices and for insuring compliance with all governmental regulations.9. NoteNotes are not a requirement of this specifi cation. 9.1 The procurement documents should establish the responsibility for samples, testing, and any required affi davit certifying full compliance with the specifi cation.