SANS 95-6-2009 Mobile waste containers Part 6 Safety and health requirements《移动式废品收集箱 第6部分：安全及卫生要求》.pdf

《SANS 95-6-2009 Mobile waste containers Part 6 Safety and health requirements《移动式废品收集箱 第6部分：安全及卫生要求》.pdf》由会员分享，可在线阅读，更多相关《SANS 95-6-2009 Mobile waste containers Part 6 Safety and health requirements《移动式废品收集箱 第6部分：安全及卫生要求》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-23819-3 SANS 95-6:2009Edition 1 and EN amdt 1EN 840-6:2008Edition 2 and amdt 1SOUTH AFRICAN NATIONAL STANDARD Mobile waste containers Part

4、 6: Safety and health requirements This national standard is the identical implementation of EN 840-6:2008 (which incorporates EN amendment 1), and is adopted with the permission of CEN, rue de Stassart 36, B-1050 Brussels. Published by SABS Standards Division 1 Dr Lategan Road Groenkloof Private Ba

5、g X191 Pretoria 0001Tel: +27 12 428 7911 Fax: +27 12 344 1568 www.sabs.co.za SABS SANS 95-6:2009 Edition 1 and EN amdt 1 EN 840-6:2008 Edition 2 and amdt 1 Table of changes Change No. Date Scope EN amdt 1 2008 Amended to modify the requirements for handles. National foreword This South African stand

6、ard was approved by National Committee SABS TC 122, Packaging, in accordance with procedures of the SABS Standards Division, in compliance with annex 3 of the WTO/TBT agreement. This SANS document was published in December 2009. EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 840-6:2004+A1 July

7、 2008 ICS 13.030.40 Supersedes EN 840-6:2004English Version Mobile waste containers - Part 6: Safety and health requirements Conteneurs roulants dchets - Partie 6: Exigences dhygine et de scurit Fahrbare Abfallsammelbehlter - Teil 6: Sicherheits- und Gesundheitsschutzanforderungen This European Stan

8、dard was approved by CEN on 10 December 2003 and includes Amendment 1 approved by CEN on 6 June 2008. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. U

9、p-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation

10、under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Gree

11、ce, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Manageme

12、nt Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 840-6:2004+A1:2008: ESANS 95-6:2009This s tandard may only be used and printed by approved subscription and freemailing clients of

13、the SABS .EN 840-6:2004+A1:2008 (E) 2 Contents page Foreword3 1 Scope 4 2 Normative references 4 3 General requirements of construction 4 4 Handles .4 5 Wheels 6 6 Direction block.7 7 Brakes .7 8 Edges 7 9 Lids7 10 Cleaning7 11 Instructions for use .8 Annex A (informative) A-Deviations 9 Bibliograph

14、y 10 SANS 95-6:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .EN 840-6:2004+A1:2008 (E) 3 Foreword This document (EN 840-6:2004+A1:2008) has been prepared by Technical Committee CEN/TC 183 “Waste management”, the secretariat of which is

15、held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2009 and conflicting national standards shall be withdrawn at the latest by January 2009. This document supersedes !EN 840-6:20

16、04“. The start and finish of text introduced or altered by amendment is indicated in the text by tags ! “. This European Standard is one part of the series of standards of EN 840 about “Mobile waste containers“ comprising the following parts: Part 1: Containers with 2 wheels with a capacity up to 40

17、0 l for comb lifting devices - Dimensions and design. Part 2: Containers with 4 wheels with a capacity up to 1 300 l with flat lid(s), for trunnion and/or comb lifting devices - Dimensions and design. Part 3: Containers with 4 wheels with a capacity up to 1 300 l with dome lid(s), for trunnion and/o

18、r comb lifting devices - Dimensions and design. Part 4: Containers with 4 wheels with a capacity up to 1700 l with flat lid(s), for wide trunnion or BG- and/or wide comb lifting devices - Dimensions and design. Part 5: Performance requirements and test methods. Part 6: Safety and health requirements

19、. Annex A is informative. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,

20、 Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. SANS 95-6:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .E

21、N 840-6:2004+A1:2008 (E) 4 1 Scope This European Standard provides the essential safety, health and ergonomic requirements for mobile waste containers according to EN 840-1 to EN 840-4, not including hazardous wastes containers. 2 Normative references This European Standard incorporates, by dated or

22、 undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only

23、when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). EN 840-5:2004, Mobile waste containers Part 5: Performance requirements and test methods. 3 General requirements of construction 3.1 The containe

24、r shall be constructed so that when it is unloaded or loaded with a nominal load, it has a secure fit on an approved compatible lifting device and must be automatically locked safely into the lifting device during the tilting and emptying operation. 3.2 The container shall be safely fitted to the li

25、fting device of the vehicle without being carried or lifted manually. 3.3 Wheeled containers shall be constructed so that under test conditions according to EN 840-5 the pushing and pulling forces to keep the container moving shall not exceed the values given in EN 840-5:2004, 4.9. Pushing and pulli

26、ng forces shall be declared in the instructions for use (see clause 11). 3.4 During construction of containers the following factors influencing measurable handling force shall be optimised: design of container as regards to form, size and position of centre of gravity in relation to positioning of

27、wheels and handles; even distribution of loads on wheels; low rolling resistance. 4 Handles 4.1 Two wheeled containers shall have handles for pulling, pushing and manoeuvring the container that enable the operator to grip safely with two hands. Four wheeled containers shall have handles for pushing,

28、 pulling, manoeuvring and lifting the container. Injuries caused by sharp edges shall be avoided. 4.2 Handles for pulling, pushing and manoeuvring the container shall have one of the external forms as shown in Figure 1 (based on the external form of Figure 1 ring form section and U-shaped form secti

29、on are permitted). A minimum length of 120 mm and a minimum clearance of 36 mm around the handle is required (see Figure 2). SANS 95-6:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .EN 840-6:2004+A1:2008 (E) 5 !4.3 Handles for pulling, p

30、ushing and manoeuvring the container shall be positioned at a height of (90040025+) mm (measured in the middle of the handle) above the ground. On two wheeled containers, for containers with a volume 140 l, these handles shall have a minimum height of 800 mm in a tilted position (centre of gravity a

31、bove the wheel axle). For containers less than 140 l the handles shall have a minimum height of 700 mm. On four wheeled containers vertical handles are optional. If two handles are fitted they shall be a minimum of 450 mm apart and shall cover a height range from 780 mm to 1 050 mm.“ 4.4 Handles for

32、 lifting containers over kerbstones shall be at a height of between 700 mm and 850 mm from the ground. 4.5 If handles are positioned above the trunnion they shall have a safety guard according to Figure 3. Dimensions in mm Figure 1 Handles (round, oval, rectangular) Dimensions in mm Key 1 Handle Fig

33、ure 2 Clearance SANS 95-6:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .EN 840-6:2004+A1:2008 (E) 6 Dimensions in mm Key 1 Handle 2 Trunnion Figure 3 Handles above trunnion 5 Wheels 5.1 Containers with 4 wheels and a capacity not exceed

34、ing 1 700 l shall only have swivel castor wheels. Containers for towing with four wheels can have two fixed wheels or wheels which could be fixed. 5.2 The wheels and their position shall ensure a minimum of pushing/pulling force and good stability. 5.3 The wheels on all containers shall have a nomin

35、al diameter of 200 mm. Wheels of nominal diameter of 160 mm on 4 wheeled containers are optional provided the pulling and pushing forces are not exceeded (see 3.3). 5.4 All wheels or castors shall be constructed to resist static and dynamic stress, e. g. by rolling against kerbstones (test according

36、 to EN 840-5). 5.5 If castor-mounting brackets are used they shall not protrude beyond the widest part of the container body. SANS 95-6:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .EN 840-6:2004+A1:2008 (E) 7 6 Direction block When dir

37、ection blocks are fitted on containers with 4 wheels they shall be fitted to at least 2 wheels. 7 Brakes 7.1 General When brakes are fitted on containers with 4 wheels they shall be fitted to at least 2 wheels. 7.2 The brakes shall be adjustable or self-compensating and capable of retaining the cont

38、ainer on a minimum slope of ten degrees to the horizontal. 7.3 Brakes shall be capable of being used easily by the operator. 7.4 If containers are fitted with a central brake locking system it must be possible to secure it against unauthorised unlocking. 7.5 The brakes shall be tested according to E

39、N 840-5:2004, 4.9.4. 8 Edges 8.1 The container shall not have any sharp edges (a radius less than 1,4 mm). 8.2 All edges which may be used for manoeuvring shall be rounded so that nobody can be injured. 9 Lids 9.1 To avoid the danger of crushed fingers when closing the lid, dome lids shall have a sa

40、fety clearance to the front edge of at least 35 mm. The gap shall be closed by an elastic material. Flat lids shall not damage fingers. 9.2 Containers with dome lids shall be provided with a mechanism to hold the lid open automatically and prevent it from accidentally closing. 9.3 Containers with as

41、sisted lids shall be provided with a device to ensure that the container lid cannot cause injury by its movement. 9.4 The dome lid container shall be designed in such a manner that, in particular, a childs head cannot be trapped between lid and body of the container. For dome lid container, a minimu

42、m gap of 181 mm shall be kept between lid and body of the container. This gap shall not be closed either automatically (by spring force or gravity) or unintentionally by a childs hand force. The container shall be tested according to EN 840-5:2004, 4.11.5. 10 Cleaning Containers shall be designed fo

43、r easy cleaning. SANS 95-6:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .EN 840-6:2004+A1:2008 (E) 8 11 Instructions for use 11.1 Instructions for use shall be supplied so that the operator can have access to all available information o

44、n the correct use of containers. Those instructions shall give information on all relevant factors to enable correct usage of a container. Also safety and health requirements shall be included. 11.2 In order to give purchasers and all users of the container the necessary information to enable them t

45、o correctly choose and safely use the containers, the information provided shall as a minimum include: number of the European Standard (e.g. EN 840-2); volume; total permissible mass; wheel diameter; type of the wheel bearings; whether direction blocks are fitted or not; whether brakes are equipped

46、or not; adjusted braking torque; whether a central brake lock is equipped; pulling force, measured using the type test (see EN 840-5); essential dimensions including height of handles in the upright and tilted position. This information shall conform to the delivered container. SANS 95-6:2009This s

47、tandard may only be used and printed by approved subscription and freemailing clients of the SABS .EN 840-6:2004+A1:2008 (E) 9 Annex A (informative) A-Deviations A-Deviation: National deviation due to regulations, the alteration of which is for the time being outside the competence of the CEN/CENELE

48、C-member. This European Standard does not fall under any Directive of the EC. In the relevant CEN/CENELEC-countries these A-deviations are valid instead of the fixations of the European Standard until they have been removed. DENMARK The EN 840-1 to EN 840-6 do not fulfil the national Danish legislat

49、ion regarding requirements for health and safety. This legislation is based on EEC-Directive 89/391/EC of 12 June 1989 and EEC-Directive 90/269/EEC of 29 May 1990. The Danish legislation is written down in “Executive Order No. 867 of 13 October 1994 concerning Performan-ce of Work“ and in “Executive Order No. 1164 of 16 December 1994 concerning Manual Handling“ both given by the Minister of Work. The Legal understanding of the Executive Orders are written in the Danish Working Environment Service (WES) guidelines. WES-guideline No. 4