SANS 5183-1-2008 Resistance welding equipment - Electrode adaptors male taper 1 10 Part 1 Conical fixing taper 1 10《电阻焊接设备 外锥度1 10的电极接头 第1部分 锥度1 10的锥形固定接头》.pdf

《SANS 5183-1-2008 Resistance welding equipment - Electrode adaptors male taper 1 10 Part 1 Conical fixing taper 1 10《电阻焊接设备 外锥度1 10的电极接头 第1部分 锥度1 10的锥形固定接头》.pdf》由会员分享，可在线阅读，更多相关《SANS 5183-1-2008 Resistance welding equipment - Electrode adaptors male taper 1 10 Part 1 Conical fixing taper 1 10《电阻焊接设备 外锥度1 10的电极接头 第1部分 锥度1 10的锥形固定接头》.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-21307-7 SANS 5183-1:2008Edition 2ISO 5183-1:1998Edition 2SOUTH AFRICAN NATIONAL STANDARD Resistance welding equipment Electrode adaptors,

4、male taper 1:10 Part 1: Conical fixing, taper 1:10 This national standard is the identical implementation of ISO 5183-1:1998 and is adopted with the permission of the International Organization for Standardization. Published by Standards South Africa 1 dr lategan road groenkloof private bag x191 pre

5、toria 0001 tel: 012 428 7911 fax: 012 344 1568 international code + 27 12 www.stansa.co.za Standards South Africa SANS 5183-1:2008 Edition 2 ISO 5183-1:1998 Edition 2 Table of changes Change No. Date Scope National foreword This South African standard was approved by National Committee StanSA TC 512

6、0.08, Welding and allied processes, in accordance with procedures of Standards South Africa, in compliance with annex 3 of the WTO/TBT agreement. This SANS document was published in June 2008. This SANS document supersedes SABS ISO 5183-1:1988 (first edition). AReference numberISO 5183-1:1998(E)INTE

7、RNATIONALSTANDARDISO5183-1Second edition1998-09-01Resistance welding equipment Electrodeadaptors, male taper 1:10 Part 1:Conical fixing, taper 1:10quipement de soudage par rsistance Allonges dlectrode emboutamovible, cne mle 1:10 Partie 1: Emmanchement conique 1:10SANS 5183-1:2008This s tandard may

8、only be used and printed by approved subscription and freemailing clients of the SABS .ISO 5183-1:1998(E) ISO 1998All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronicor mechanical, including photocopying an

9、d microfilm, without permission in writing from the publisher.International Organization for StandardizationCase postale 56 CH-1211 Genve 20 SwitzerlandInternet isoiso.chPrinted in SwitzerlandiiForewordISO (the International Organization for Standardization) is a worldwide federation of national sta

10、ndards bodies (ISOmember bodies). The work of preparing International Standards is normally carried out through ISO technicalcommittees. Each member body interested in a subject for which a technical committee has been established hasthe right to be represented on that committee. International organ

11、izations, governmental and non-governmental, inliaison with ISO, also take part in the work. ISO collaborates closely with the International ElectrotechnicalCommission (IEC) on all matters of electrotechnical standardization.Draft International Standards adopted by the technical committees are circu

12、lated to the member bodies for voting.Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.Publication as an International Standard requires approval by at least 75 % of the national bodies casting a vote.International Standard ISO 5183-1 wa

13、s prepared by Technical Committee ISO/TC 44, Welding and alliedprocesses, Subcommittee SC 6, Resistance welding.ISO 5183 consists of the following parts, under the general title Resistance welding equipment Electrodeadaptors, male taper 1:10: Part 1: Conical fixing, taper 1:10 Part 2: Parallel shank

14、 fixing for end-thrust electrodesThis second edition is a revision of the first edition (ISO 5183-1:1988), which has been technically revised.Annexes A and B of this part of ISO 5183 are for information only.SANS 5183-1:2008This s tandard may only be used and printed by approved subscription and fre

15、emailing clients of the SABS . ISOISO 5183-1:1998(E)iiiIntroductionThis part of ISO 5183 is an updated edition of ISO 5183-1:1988 and is largely based on the former version.It is extended to adaptors with longer taper fits (type C) conforming to ISO 1089:1980, type B.These electrode adaptors are des

16、igned to be used when electrodes are mounted at an angle.SANS 5183-1:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .SANS 5183-1:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS

17、.INTERNATIONAL STANDARD ISO ISO 5183-1:1998(E)1Resistance welding equipment Electrode adaptors, maletaper 1:10 Part 1:Conical fixing, taper 1:101 ScopeThis part of ISO 5183 specifies the dimensions and tolerances of resistance spot welding electrode adaptors wherethe fixing element for the cap (see

18、ISO 5821) is a male taper of 1:10 and for which the electrode taper fits inconformance with ISO 1089.2 Normative referencesThe following standards contain provisions which, through reference in this text, constitute provisions of this part ofISO 5183. At the time of publication, the editions indicat

19、ed were valid. All standards are subject to revision, andparties to agreements based on this part of ISO 5183 are encouraged to investigate the possibility of applying themost recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently validInternational

20、Standards.ISO 5182:1991, Welding Materials for resistance welding electrodes and ancillary equipment.ISO 5821:1979, Resistance spot welding electrode caps.3 DimensionsThe dimensions shall be those given in figure 1, table 1 and table 2.4 DesignationThe designation of electrode adaptors which comply

21、with this part of ISO 5183 shall include the followinga) the description block (i. e. “spot welding electrode adaptor“);b) reference to this part of ISO 5183, i. e. ISO 5183-1;c) the type of electrode adaptor, according to figure 1;d) the diameter, d1, in millimetres;e) the length, l1, in millimetre

22、s;f) the material of which the electrode adaptor is made, in accordance with ISO 5182.EXAMPLEA type A spot welding electrode adaptor, of diameter d1= 16 mm, length l1= 58 mm and material type A 2/1, shall bedesignated as follows:Spot welding electrode adaptor ISO 5183-1 A - 16 58 A 2/1SANS 5183-1:20

23、08This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 5183-1:1998(E) ISO25 MaterialsThe material of which the electrode adaptor is made shall be in accordance with ISO 5182:1991, preferablygroup A, type 2.6 MarkingElectrode adaptors complying

24、 with this part of ISO 5183 shall be marked with the designation laid down in clause 4,but excluding the description block and the reference number of this part of ISO 5183, for example:A 16 58 A 2/1SANS 5183-1:2008This s tandard may only be used and printed by approved subscription and freemailing

25、clients of the SABS . ISOISO 5183-1:1998(E)3Dimensions in millimetresSurface roughness values in micrometres1) Cone diameter at the gauge plane.NOTE The adaptors of type A and B are designed to be held by electrode holders which conform to ISO 8430-1 and ISO 8430-2.The adaptors of type C are designe

26、d to fit in tapers according to ISO 1089.Figure 1 Electrode adaptorsSANS 5183-1:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 5183-1:1998(E) ISO4Table 1 Dimensions for adaptors type A and BDimensions in millimetresd1h11d21)d31)d4l2

27、0,5l3l4l1for l52)=31,5 40 50 63 80 100 125 (140) 160 (180) 20013 12,7 10 6,5 6,5 10 16 36 44,5 54,5 67,5 84,5 104,5 129,5 16 15,5 12 8 8 13 20 48 58 71 88 108 133 148 168 20 19 15 10,5 10 15 25 63 76 93 113 138 153 173 193 2131) Cone diameter at the gauge plane.2) Values shown in parentheses are non

28、-preferred sizes.Table 2 Dimensions for adaptors type CDimensions in millimetresd1h11d21)d31)d4l2 0,5l3l4l1for l52) =31,5 40 50 63 80 100 125 (140) 160 (180) 20013 12,7 10 6,5 6,5 10 25 45 53,5 63,5 76,5 93,5 113,5 138,5 16 15,5 12 8 8 13 31,5 59,5 69,5 82,5 99,5 119,5 144,5 159,5 179,5 20 19 15 10,

29、5 10 15 40 78 91 108 128 153 168 188 208 2281) Cone diameter at the gauge plane.2) Values shown in parentheses are non-preferred sizes.SANS 5183-1:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS . ISOISO 5183-1:1998(E)5Annex A(informative)

30、Flat dimensionsIf electrode adaptors are designed with flats for a wrench to thus enable easier release of the adaptor from a holder,the flat dimensions b and lf(see figure A.1) according to Table A.1 can be used.Figure A.1 Adaptors with flatsTable A.1 Flat dimensionsDimensions in millimetresd1h11bl

31、f13 11 716 13 820 17 8SANS 5183-1:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 5183-1:1998(E) ISO6Annex B(informative)Bibliography1 ISO 1089:1980, Electrode taper fits for spot welding equipment Dimensions.2 ISO 5183-2:1988, Resist

32、ance spot welding Electrode adaptors, male taper 1:10 Part 2: Parallel shank fixingfor end-thrust electrodes.3 ISO 8430-1:1988, Resistance spot welding Electrode holders Part 1: Taper fixing 1:10.4 ISO 8430-2:1988, Resistance spot welding Electrode holders Part 2: Morse taper fixing.SANS 5183-1:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .