SAE AS 25065A-2011 Ferrule Flexible Conduit Radio Frequency Shielding《无线电频率屏蔽的柔性导线管套圈》.pdf

《SAE AS 25065A-2011 Ferrule Flexible Conduit Radio Frequency Shielding《无线电频率屏蔽的柔性导线管套圈》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 25065A-2011 Ferrule Flexible Conduit Radio Frequency Shielding《无线电频率屏蔽的柔性导线管套圈》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARD (R) FERRULE, FLEXIBLE CONDUIT, RADIO FREQUENCY SHIELDING AS25065Copyright 2010 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, reco

2、rding, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2004-04REVISED 2011-07THIRD ANGLE PROJEC

3、TION CUSTODIAN: AE-8/AE-8A REV.AFEDERAL SUPPLY CLASS 5975 AS25065SHEET 1 OF 2REV. APROCUREMENT SPECIFICATION: NONESAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirely voluntary, andit

4、s applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay bereaffirmed, revised, orcancelled. SAE invites yourwrittencomments andsuggesti

5、ons. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS25065ARATIONALE REQUIRED TO CLARIFY DRAWINGS AND ADDRESS REFERENCES NOTICE AS25065 PROVIDES PIECE PARTS FOR AS25067 CONDUIT ASSEMBLIES, REQUIRES NO QUALIFICATION, AND HAS NO

6、PROCUREMENT SPECIFICATION FIGURE 1 AS25065-2 COLLAR AND NUT ASSEMBLY FOR AS25067 CONDUIT ASSEMBLIES TABLE 1 AS25065 COLLAR AND NUT DIMENSIONS DASH NO.CONDUITSIZE NOMINAL A DIA B DIA C DIA D DIA E.0005 F.0002 G RSPHER MS25065 MAX MIN MAX MIN MAX MIN MAX MIN FERRULE PART NO. COLLAR PART NO. -2 3/16 .4

7、25 .452 .438 .433 .393 .383 .173 .168 .130 .3640 .250 .257 -24 -25 Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS25065SHEET 2 OF 2REV. A(R) FERRULE, FLEXIBLE CONDUIT, RADIO FRE

8、QUENCY SHIELDING FIGURE 2 AS25065 FERRULE TABLE 2 AS25065 FERRULE DIMENSIONS DASHNO. CONDUIT SIZENOMINAL A DIA B DIA C DIA D DIA E.005 F.0002 DIA G RSPHERMAX MIN MAX MIN MAX MIN MAX MIN -3 3/16 .576 .571 .500 .495 .393 .383 .173 .168 .130.4900 .250.346-4 1/4 .445 .440 .235 .230 -5 5/16 .638 .633 .56

9、3 .558 .522 .518 .313 .308 .5300 .375 -6 3/8 .692 .687 .625 .620 .573 .566 .360 .355 .6040 .380.427 -8 1/2 .817 .812 .758 .753 .716 .712 .485 .480 .7290 .515 -10 5/8 .942 .937 .883 .878 .841 .837 .610 .605 .8540 .604 -12 3/4 1.123 1.118 1.057 1.052 .978 .972 .735 .732 1.0340 .440.731 -16 1 1.373 1.3

10、67 1.307 1.302 1.264 1.260 .985 .980 1.2840 .908 -18 1-1/8 1.567 1.562 1.500 1.495 1.423 1.417 1.141 1.136 .162 1.4790 1.046 -22 1-3/8 1.805 1.801 1.741 1.736 1.696 1.692 1.355 1.350 .193 1.6910 .500 1.195 WARNINGTHIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT L

11、OCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. REQUIREMENTS 1. DIMENSION ARE IN INCHES UNLESS OTHERWISE SPECIFIED, TOLERANCES: DECIMALS .010, ANGLES 2 DEGREES. 2. MATERIAL: FERRULE AND COLLAR; BRASS IN ACCORDANCE WITH ASTM-B121, -B36, -B16, B16M, AND B124 COMP 11, 1/2 HARD AS APPLICAB

12、LE. 3. FINISH: CADMIUM PLATE, SPECIFICATION AMS-QQ-P-416, TYPE 1, CLASS 2. 4. WORKMANSHIP: REMOVE ALL BURRS AND SHARP EDGES 5. PART NUMBER EXAMPLE MS25065- 2I I_ COLLAR AND NUT ASSEMBLY I_ CONDUIT FERRULE SPECIFICATION NUMBER 6. A CHANGE BAR (|) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF T

13、HE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-