SAE AMS 4064F-2008 Aluminum Alloy Clad Two Sides Sheet 1 25Mn - 0 12Cu (No 12-0 Brazing Sheet) Annealed (UNS A83003)《1 25Mn 0 12Cu (No 12-0钎接金属片)退火的双面涂覆铝合金薄板材》.pdf

《SAE AMS 4064F-2008 Aluminum Alloy Clad Two Sides Sheet 1 25Mn - 0 12Cu (No 12-0 Brazing Sheet) Annealed (UNS A83003)《1 25Mn 0 12Cu (No 12-0钎接金属片)退火的双面涂覆铝合金薄板材》.pdf》由会员分享，可在线阅读，更多相关《SAE AMS 4064F-2008 Aluminum Alloy Clad Two Sides Sheet 1 25Mn - 0 12Cu (No 12-0 Brazing Sheet) Annealed (UNS A83003)《1 25Mn 0 12Cu (No 12-0钎接金属片)退火的双面涂覆铝合金薄板材》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、_SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising theref

2、rom, is the sole responsibility of the user.”SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions.Copyright 2013 SAE InternationalAll rights reserved. No part of this publication may b

3、e reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada)Tel: +1 724-776-4970 (outside USA)Fax

4、: 724-776-0790Email: CustomerServicesae.orgSAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedbackon this Technical Report, please visithttp:/www.sae.org/technical/standards/AMS4064FAEROSPACEMATERIALSPECIFICATIONAMS4064 REV. FIssued 1968-05Revised 2008-01Reaffirmed 2013-05Supers

5、eding AMS4064EAluminum Alloy, Clad Two Sides Sheet1.25Mn - 0.12Cu (No. 12-0 Brazing Sheet)Annealed(Compositions similar to UNS A83003)RATIONALEAMS4064F has been reaffirmed to comply with the SAE five-year review policy.1. SCOPE1.1 FormThis specification covers an aluminum alloy in the form of clad s

6、heet.1.2 ApplicationThis sheet has been used typically for brazed assemblies which are not subject to heat treatment after joining, but usage is not limited to such applications.2. APPLICABLE DOCUMENTSThe issue of the following documents in effect on the date of the purchase order forms a part of th

7、is specification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall

8、 apply.2.1 SAE PublicationsAvailable from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org.AMS 2355 Quality Assurance Sampling and Testing, Aluminum Alloys and Magnesium Alloys, Wrought Products

9、, Except Forging Stock, and Rolled, Forged, or Flash Welded Rings2.2 ASTM PublicationsAvailable from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.org.ASTM B 660 Packaging/Packing of Aluminum and Magnesium ProductsASTM B 666/B

10、 666M Identification Marking of Aluminum and Magnesium ProductsSAE AMS4064F Page 2 of 52.3 ANSI PublicationsAvailable from American National Standards Institute, 25 West 43rd Street, New York, NY 10036, Tel: 212-642-4900, www.ansi.org.ANSI H35.2 Dimensional Tolerances for Aluminum Mill ProductsANSI

11、H35.2M Dimensional Tolerances for Aluminum Mill Products (Metric)3. TECHNICAL REQUIREMENTS3.1 CompositionShall conform to the percentages by weight shown in Table 1 and Table 2, determined in accordance with AMS 2355.TABLE 1 - COMPOSITION, CORE (3003)Element min maxSiliconIronCopperManganeseZincOthe

12、r elements, eachOther elements, totalAluminum-0.051.0-remainder0.60.70.201.50.100.050.15TABLE 2 - COMPOSITION, CLADDING (4343)Element min maxSiliconIronCopperManganeseZincOther elements, eachOther elements, totalAluminum6.8-remainder8.20.80.250.100.200.050.153.2 ConditionAnnealed (See 8.5).3.3 Prope

13、rtiesSheet shall conform to the following requirements, determined on the mill produced size in accordance with AMS 2355.SAE AMS4064F Page 3 of 53.3.1 Tensile PropertiesShall be as shown in Table 3.TABLE 3A - TENSILE PROPERTIES, INCH/POUND UNITSNominal Thickness InchTensile Strengthksi, maxElongatio

14、n in2 inches or 4D%, min0.006 to 0.007, inclOver 0.007 to 0.012, inclOver 0.012 to 0.031, inclOver 0.031 to 0.050, inclOver 0.050 to 0.249, incl20.020.020.020.020.01215182023TABLE 3B - TENSILE PROPERTIES, SI UNITSNominal ThicknessMillimetersTensileStrengthMPa, maxElongation in50.8 mm or 4D%, min0.15

15、 to 0.18, inclOver 0.18 to 0.30, inclOver 0.30 to 0.79, inclOver 0.79 to 1.27, inclOver 1.27 to 6.32, incl13813813813813812151820233.3.2 BendingSheet shall withstand, without cracking, bending at room temperature flat on itself with axis of bend parallel to the directionof rolling.3.3.3 CladdingShal

16、l be applied to both faces of the core.3.3.3.1 Cladding ThicknessAfter rolling, the average cladding thickness shall be as shown in Table 4.TABLE 4 - AVERAGE CLADDING THICKNESSTotal Thicknessof Composite ProductInchTotal Thicknessof Composite ProductMillimetersAverageCladding ThicknessPer Side% ofTo

17、tal ThicknessUp to 0.063, inclOver 0.063 to 0.250, exclUp to 1.60, inclOver 1.60 to 6.35, excl8 to 124 to 63.4 QualitySheet, as received by purchaser, shall be uniform in quality and condition, sound, and free from foreign materials and from imperfections detrimental to usage of the sheet.3.5 Tolera

18、ncesShall conform to all applicable requirements of ANSI H35.2 or ANSI H35.2M.SAE AMS4064F Page 4 of 54. QUALITY ASSURANCE PROVISIONS4.1 Responsibility for InspectionThe vendor of sheet shall supply all samples for vendors tests and shall be responsible for the performance of all required tests. Pur

19、chaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that the sheet conforms to specified requirements.4.2 Classification of Tests4.2.1 Acceptance TestsComposition (3.1), tensile properties (3.3.1), and tolerances (3.5) are acceptance tests and, exce

20、pt for composition, shall be performed on each inspection lot.4.2.2 Periodic TestsBending (3.3.2) and cladding thickness (3.3.3.1) are periodic tests and shall be performed at a frequency selected by the vendor unless frequency of testing is specified by purchaser.4.3 Sampling and TestingShall be in

21、 accordance with AMS 2355.4.4 ReportsThe vendor of clad sheet shall furnish with each shipment a report stating that the sheet conforms to the composition and showing the results of tests on each inspection lot to determine conformance to the other acceptance test requirements and, when performed, t

22、o the periodic test requirements. This report shall include the purchase order number, inspection lot number, AMS 4064F, size, and quantity. This report shall also identify the producer, the product form, and the size of the mill product.4.5 Resampling and RetestingShall be in accordance with AMS 23

23、55.5. PREPARATION FOR DELIVERY5.1 IdentificationShall be in accordance with ASTM B 666/B 666M.5.2 Packaging5.2.1 Product shall be protected from damage during storage and shipment by a method determined by vendor unless specified by purchaser. Examples of typical protective methods include but are n

24、ot limited to interleaving with paper or oiling of the surfaces.5.2.2 Sheet shall be prepared for shipment in accordance with ASTM B 660 and in compliance with applicable rules and regulations pertaining to the handling, packaging, and transportation of the sheet to ensure carrier acceptance and saf

25、e delivery. 6. ACKNOWLEDGMENTA vendor shall include this specification number and its revision letter in all quotations and when acknowledging purchase orders.SAE AMS4064F Page 5 of 57. REJECTIONSSheet not conforming to this specification, or to modifications authorized by purchaser, will be subject

26、 to rejection.8. NOTES8.1 A change bar (|) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this specification. An (R) symbol to the left of the document title indicates a complet

27、e revision of the specification, including technical revisions. Change bars and (R) are not used in original publications, nor in specifications that contain editorial changes only.8.2 Terms used in AMS are clarified in ARP1917.8.3 Dimensions and properties in inch/pound units and the Fahrenheit tem

28、peratures are primary; dimensions and properties in SI units and the Celsius temperatures are shown as the approximate equivalents of the primary units and are presented only for information.8.4 Purchase documents should specify not less than the following:AMS 4064FSize of sheet desiredCondition, if

29、 other than Annealed (See 3.2 and 8.5)Quantity of sheet desired.8.5 This material is occasionally procured in the as-fabricated condition, similar to the H12 or H14 condition of other aluminum alloys, for ease of handling or other reasons. When so ordered, the mechanical properties presented inthis specification are not applicable.PREPARED BY AMS COMMITTEE “D“