SAE AMS 1450A-1986 Disinfectant (Insecticide) Aircraft《飞机用消毒剂(杀虫剂)》.pdf

《SAE AMS 1450A-1986 Disinfectant (Insecticide) Aircraft《飞机用消毒剂(杀虫剂)》.pdf》由会员分享，可在线阅读，更多相关《SAE AMS 1450A-1986 Disinfectant (Insecticide) Aircraft《飞机用消毒剂(杀虫剂)》.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and enginee ring sciences. The use of this report is entirelyvoluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefr

2、om, is the sole responsibility of the user.”SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invit es your written comments and suggestions.Copyright 1998 Society of Automotive Engineers, Inc.All rights reserved. Printed in U.

3、S.A.QUESTIONS REGARDING THIS DOCUMENT: (724) 772-7161 FAX: (724) 776-0243TO PLACE A DOCUMENT ORDER: (724) 776-4970 FAX: (724) 776-0790SAE WEB ADDRESS: http:/www.sae.org400 Commonwealth Drive, Warrendale, PA 15096-0001AEROS PACE MATERIAL SPECIFIC ATIONSubmitted for recognition as an American National

4、 StandardAMS 1450AIssued Jan 1979Revised JAN 1986Reaffirmed JUN 1998Superseding AMS 1450Disinsectant (Insecticide), Aircraft1. SCOPE:1.1 Form: This specification covers insecticides for use in disinsection of aircraft as required on international passenger flights.1.2 Application: Primarily as disin

5、sectant of aircraft where required by the U.S. Department of Agriculture, the World Health Organization, or member states.2. APPLICABLE DOCUMENTS: The following publications form a part of this specification to the extent specified herein. The latest issue of Aerospace Material Specifications and Ae

6、rospace Recommended Practices shall apply. The applicable issue of other documents shall be as specified in AMS 2350.2.1 SAE Publications: Available from SAE, 400 Commonwealth Drive, Warrendale, PA 15096.AMS 2350 Standards and Test MethodsAMS 2820 Aerosol PackagingAMS 2825 Material Safety Data Sheet

7、sAMS 4049 Aluminum Alloy Sheet and Plate, Alclad, 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (Alclad 7075; -T6 Sheet, -T651 Plate)ARP1512 Corrosion of Aluminum Alloys by Aircraft Maintenance Chemicals, Sandwich TestAMS 1450A SAE AMS 1450A- 2 -2.2 ASTM Publications: Available from ASTM, 100 Barr Harbor Drive, We

8、st Conshohocken, PA 19428-2959.ASTM D 56 Flash Point by Tag Closed TesterASTM D 891 Specific Gravity of Industrial Aromatic Hydrocarbons and Related MaterialsASTM D 1078 Distillation Range of Volatile Organic LiquidsASTM D 1353 Nonvolatile Matter in Volatile Solvents for Use in Paint, Varnish, Lacqu

9、er, and Related ProductsASTM D 1568 Sampling and Chemical Analysis of Alkylbenzene SulfonatesASTM F 483 Total Immersion Corrosion Test for Aircraft Maintenance ChemicalsASTM F 484 Stress Crazing of Acrylic Plastics in Contact with Liquid or Semi-Liquid CompoundsASTM F 502 Effects of Cleaning and Che

10、mical Maintenance Materials on Painted Aircraft SurfacesASTM F 503 Preparing Aircraft Cleaning Compounds, Liquid Type, For Storage Stability Testing2.3 U.S. Government Publications: Available from DODSSP, Subscription Services Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.MIL-P-

11、83310 Plastic Sheet, Polycarbonate, TransparentMIL-STD-794 Parts and Equipment, Procedures for Packaging and Packing of3. TECHNICAL REQUIREMENTS: 3.1 Composition: Shall be optional with the manufacturer, shall meet the requirements of 3.1.1, shall be nonflammable up to 65 C (150 F), and shall be a u

12、niform mixture meeting the requirements of 3.2.3.1.1 Disinsectant shall comply with registration, efficiacy, toxicological, and other requirements of:World Health Organization and member states as requiredUnited States Environmental Protection AgencyUnited States Department of AgricultureUnited Stat

13、es Public Health Service3.2 Properties: Disinsectant shall conform to the following requirements; tests shall be performed in accordance with specified test methods on the disinsectant supplied in concentrated form:AMS 1450A SAE AMS 1450A- 3 -3.2.1 Flash Point: Disinsectant shall exhibit no flash po

14、int, determined in accordance with ASTM D 56.3.2.2 Residue: Two 2 x 6 in. (50 x 150 mm) panels of AMS 4049 aluminum alloy shall be cleaned with acetone and immersed in a sufficient quantity of the disinsectant to cover approximately one-half of the panel. After the disinsectant has been applied, the

15、 panels shall be placed at 45 deg from horizontal in an oven maintained at 38C 1 (100F 2) for 30 min. 1, removed from the oven, rinsed with room-temperature methyl ethyl ketone, and allowed to dry. The treated and untreated areas of the panel shall be visually examined and compared for the presence

16、of residue and stains.3.2.3 Corrosion of Metal Surfaces: 3.2.3.1 Sandwich Corrosion: Specimens of AMS 4049 aluminum alloy, after test, shall show a rating not worse than 1, determined in accordance with ARP1512.3.2.3.2 Total Immersion Corrosion: Disinsectant shall neither show evidence of pitting of

17、 the panels nor cause a weight change greater than 0.3 mg/cm 2 per 24 hr for any panel of AMS 4049 aluminum alloy, determined in accordance with ASTM F 483.3.2.4 Temperature Stability: Disinsectant shall show no chemical or physical deterioration, including evidence of discoloration, layering, or ot

18、her change denoting loss of stability, after exposure of120 hr 1 at 2 C 3 (35 F 5).3.2.5 Effect on Painted Surfaces: Disinsectant shall neither decrease the paint film hardness by more than two pencil hardness levels nor shall it produce any streaking, discoloration, or blistering of the paint film,

19、 determined in accordance with ASTM F 502.3.2.6 Effect on Transparent Plastics: Disinsectant shall not craze, stain, or discolor Type C acrylic plastic, determined in accordance with ASTM F 484. Disinsectant shall not craze, stain, or discolor MIL-P-83310 polycarbonate plastic or polysulfone plastic

20、, determined in accordance with test procedures specified in ASTM F 484 on specimens stressed for 30 min. 2 to an outer fiber stress of 3,000 psi (20 MPa).3.2.7 Specific Gravity: Shall be within 0.005 of the qualification value established as in 4.4.1, determined in accordance with ASTM D 891.AMS 14

21、50A SAE AMS 1450A- 4 -3.2.8 Distillation Range: Shall be determined in accordance with ASTM D 1078 and the following points reported:Initial Boiling Point -10% -20% -30% -40% -50% -60% -70% -80% -90% -Dry Point -3.2.9 Nonvolatile Matter: Shall be determined in accordance with ASTM D 1353 and the res

22、ults reported.3.2.10 Storage Stability: 3.2.10.1 Short-Time Test: Disinsectant shall remain homogeneous and free of lumps and skin formation and shall show no evidence of layering, separation, settling, or crystallization, determined on samples subjected to five freeze-thaw cycles as in 3.2.10.1.1.3

23、.2.10.1.1 Two 6-oz (175-mL) samples of the disinsectant shall be placed in 8-oz (250-mL) clear glass bottles and sealed and, from that time until test is completed, shall be handled so as to minimize movement of the sample. Samples shall be exposed for not less than 12 hr at-23C 1 (-10F 2). At the e

24、nd of the 12-hr period, remove sample to a room-temperature environment, and allow to thaw completely. This shall constitute one freeze-thaw cycle.3.2.10.1.2 Long-Time Storage: Disinsectant shall be stable and shall not deliquesce or otherwise deteriorate to the extent that the disinsectant will not

25、 meet the other properties of 3.2 when stored in shipping container or use package for not less than 12 months from date of receipt by purchaser, determined in accordance with ASTM F 503.3.3 Quality: Disinsectant, as received by purchaser, shall be uniform, shall show no separation or layering, and

26、shall be free from foreign materials detrimental to usage of the disinsectant.4. QUALITY ASSURANCE PROVISIONS: 4.1 Responsibility for Inspection: The vendor of disinsectant shall supply all samples of vendors tests and shall be responsible for performing all required tests. Results of such tests sha

27、ll be reported to the purchaser as required by 4.5. Purchaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that the disinsectant conforms to the requirements of this specification.AMS 1450A SAE AMS 1450A- 5 -4.2 Classification of Tests: 4.2.1 Accept

28、ance Tests: Tests to determine conformance to requirements for flash point (3.2.1) and effect on plastics (3.2.6) are classified as acceptance tests and shall be performed on each lot.4.2.2 Periodic Tests: Tests to determine conformance to requirements for residue (3.2.2), corrosion of metal surface

29、s (3.2.3), temperature stability (3.2.4), effect on painted surfaces (3.2.5), specific gravity (3.2.7), distillation range (3.2.8), nonvolatile matter (3.2.9), and storage stability (3.2.10.1) are classified as periodic tests and shall be performed at a frequency selected by the manufacturer unless

30、frequency of testing is specified by purchaser.4.2.3 Preproduction Tests: Tests to determine conformance to all technical requirements of this specification except long-time storage stability (3.2.10.2) are classified as preproduction tests and shall be performed prior to or on the initial shipment

31、of disinsectant to a purchaser, when a change in material, processing, or both requires reapproval as in 4.4.2, and when purchaser deems confirmatory testing to be required.4.2.3.1 For direct U.S. Military procurement, substantiating test data and, when requested, preproduction test material shall b

32、e submitted to the cognizant agency as directed by the procuring activity, the contracting officer, or the request for procurement.4.3 Sampling: Shall be in accordance with ASTM D 1568; a lot shall be all disinsectant produced in a continuous series of operations from the same batches of ingredients

33、 and presented for manufacturers inspection at one time.4.3.1 When a statistical sampling plan and acceptance quality level (AQL) have been agreed upon by purchaser and vendor, sampling shall be in accordance with such plan in lieu of sampling as in 4.3 and the report of 4.5 shall state that such pl

34、an was used.4.4 Approval: 4.4.1 Disinsectant shall be approved by purchaser before disinsectant for production use is supplied, unless such approval be waived by purchaser. Results of tests on production disinsectant shall be essentially equivalent to those on the approved sample.4.4.2 Vendor shall

35、use ingredients, manufacturing procedures, and methods of inspection on production disinsectant which are essentially the same as those used on the approved sample disinsectant. If necessary to make any change in ingredients or in manufacturing procedures, vendor shall submit for reapproval a statem

36、ent of the proposed changes in material, processing, or both and, when requested, sample disinsectant. Production disinsectant made by the revised procedure shall not be shipped prior to receipt of reapproval.AMS 1450A SAE AMS 1450A- 6 -4.5 Reports: Unless waived by purchaser, the vendor of disinsec

37、tant shall furnish with each shipment a report showing the results of tests to determine conformance to the acceptance test requirements and, when performed, to the periodic test requirements and stating that the disinsectant conforms to the other technical requirements of this specification. This r

38、eport shall include the purchase order number, lot number, AMS 1405A, manufacturers identification, and quantity.4.5.1 A material safety data sheet conforming to AMS 2825, or equivalent, shall be supplied to each purchaser prior to, or concurrent with, the report of preproduction test results or, if

39、 preproduction testing be waived by purchaser, concurrent with the first shipment of disinsectant for production use. Each request for modification of disinsectant formulation shall be accompanied by a revised data sheet for the proposed formulation.4.6 Resampling and Retesting: If any sample used i

40、n the above tests fails to meet the specified requirements, disposition of the disinsectant may be based on the results of testing three additional samples for each original nonconforming sample. Failure of any retest sample to meet the specified requirements shall be cause for rejection of the disi

41、nsectant represented and no additional testing shall be permitted. Results of all tests shall be reported.5. PREPARATION FOR DELIVERY: 5.1 Identification: Each exterior container shall be legibly marked with not less than AMS 1450A, purchase order number, manufacturers identification, lot number, an

42、d quantity.5.2 Packaging: 5.2.1 Disinsectant shall be packaged in containers of a type and size agreed upon by purchaser and vendor. When supplied in aerosol form, packaging shall conform to AMS 2820.5.2.2 Containers of disinsectant shall be prepared for shipment in accordance with commercial practi

43、ce and in compliance with applicable rules and regulations pertaining to the handling, packaging, and transportation of the disinsectant to ensure carrier acceptance and safe delivery. Packaging shall conform to carrier rules and regulations applicable to the mode of transportation.5.2.3 For direct

44、U.S. Military procurement, packaging shall be in accordance with MIL-STD-794, Level A or Level C, as specified in the request for procurement. Commercial packaging as in 5.2.1 and 5.2.2 will be acceptable if it meets the requirements of Level C.6. ACKNOWLEDGMENT: A vendor shall mention this specific

45、ation number and its revision letter in all quotations and when acknowledging purchase orders.AMS 1450A SAE AMS 1450A- 7 -7. REJECTIONS: Disinsectant not conforming to this specification or to modifications authorized by purchaser will be subject to rejection.8. NOTES:8.1 The change bar ( l ) locate

46、d in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this specification. An (R) symbol to the left of the document title indicates a complete revision of the specification.8.2 Dimensions an

47、d properties in inch/pound units and the Celsius temperatures are primary; dimensions and properties in SI units and the Fahrenheit temperatures are shown as the approximate equivalents of the primary units and are presented only for information.8.3 For direct U.S. Military procurement, purchase doc

48、uments should specify not less than the following:Title, number, and date of this specificationType and size of containers desiredQuantity of disinsectant desiredApplicable level of packaging (See 5.2.3)8.4 Disinsectant meeting the requirements of this specification has been classified under Federal Supply Classification (FSC) 6840.PREPARED UNDER THE JURISDICTION OF AMS COMMITTEE “J”