REG UFGS-12 32 00-2013 MANUFACTURED WOOD CASEWORK.pdf

《REG UFGS-12 32 00-2013 MANUFACTURED WOOD CASEWORK.pdf》由会员分享，可在线阅读，更多相关《REG UFGS-12 32 00-2013 MANUFACTURED WOOD CASEWORK.pdf（21页珍藏版）》请在麦多课文档分享上搜索。

1、*USACE / NAVFAC / AFCESA / NASA UFGS-12 32 00 (November 2013)-Preparing Activity: NASA SupersedingUFGS-12 32 00 (May 2009)UNIFIED FACILITIES GUIDE SPECIFICATIONSReferences are in agreement with UMRL dated October 2013*SECTION TABLE OF CONTENTSDIVISION 12 - FURNISHINGSSECTION 12 32 00MANUFACTURED WOO

2、D CASEWORK11/13PART 1 GENERAL1.1 REFERENCES1.2 SUBMITTALS1.3 MAINTENANCE MATERIAL SUBMITTALS1.4 QUALITY ASSURANCE1.5 DELIVERY, STORAGE, AND HANDLINGPART 2 PRODUCTS2.1 SYSTEM DESIGN2.2 FABRICATION2.2.1 Wood Cabinet Fabrication2.2.1.1 High-Pressure Decorative Laminate (HPDL)2.2.1.1.1 Countertops2.2.1.

3、1.2 Vertical Surfaces2.2.1.1.3 Backing Sheet2.2.1.1.4 Cabinet Liner2.2.1.2 Hardwood Plywood2.2.1.3 Hardwood2.2.1.4 Softwood Plywood2.2.1.4.1 Countertops2.2.1.4.2 Elsewhere2.2.1.5 Hardboard2.2.1.6 Steel for Cabinets2.2.1.7 Sinks , Lavatories and Fittings2.2.2 Particle Board Cabinet Fabrication2.2.3 P

4、lywood Cabinet Fabrication2.2.4 Melamine Cabinet Fabrication2.2.5 Laminate Cabinet Fabrication2.2.6 Miscellaneous Cabinets2.2.6.1 Combination Sink-and-Base Cabinet2.2.6.2 Special Purpose Cabinets2.3 MANUFACTURED UNITS2.3.1 Cabinets2.3.1.1 Frame Type CabinetsSECTION 12 32 00 Page 1Provided by IHSNot

5、for ResaleNo reproduction or networking permitted without license from IHS-,-,-2.3.1.2 Frameless Type Cabinets2.3.2 Finish2.3.2.1 Cabinet Finish2.3.2.2 Melamine Laminated Interior Cabinet Finish2.3.2.3 Backer Sheets2.3.3 Color, Texture, And Pattern2.4 MATERIALS2.5 ACCESSORIES AND HARDWAREPART 3 EXEC

6、UTION3.1 INSTALLATION3.1.1 Field Finishing Of Wood Cabinets3.1.2 Cabinet Installation3.2 CLEANING3.3 INSPECTION- End of Section Table of Contents -SECTION 12 32 00 Page 2Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-*USACE / NAVFAC / AFCESA / NASA

7、UFGS-12 32 00 (November 2013)-Preparing Activity: NASA SupersedingUFGS-12 32 00 (May 2009)UNIFIED FACILITIES GUIDE SPECIFICATIONSReferences are in agreement with UMRL dated October 2013*SECTION 12 32 00MANUFACTURED WOOD CASEWORK11/13*NOTE: This guide specification covers the requirements for wood ca

8、sework.Use this guide specification in conjunction with and coordinate with the referenced sections.Adhere to UFC 1-300-02 Unified Facilities Guide Specifications (UFGS) Format Standard when editing this guide specification or preparing new project specification sections. Edit this guide specificati

9、on for project specific requirements by adding, deleting, or revising text. For bracketed items, choose applicable items(s) or insert appropriate information.Remove information and requirements not required in respective project, whether or not brackets are present.Comments, suggestions and recommen

10、ded changes for this guide specification are welcome and should be submitted as a Criteria Change Request (CCR).*PART 1 GENERAL1.1 REFERENCES*NOTE: This paragraph is used to list the publications cited in the text of the guide specification. The publications are referred to in the text by basic desi

11、gnation only and listed in this paragraph by organization, designation, date, and title.Use the Reference Wizards Check Reference feature when you add a RID outside of the Sections Reference Article to automatically place the reference in the Reference Article. Also use the Reference Wizards Check R

12、eference feature to update SECTION 12 32 00 Page 3Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-the issue dates.References not used in the text will automatically be deleted from this section of the project specification when you choose to reconcil

13、e references in the publish print process.*The publications listed below form a part of this specification to the extent referenced. The publications are referred to within the text by the basic designation only.AMERICAN HARDBOARD ASSOCIATION (AHA)AHA A135.4 (1995; R 2004) Basic HardboardAPA - THE E

14、NGINEERED WOOD ASSOCIATION (APA)APA E30 (2011) Engineered Wood Construction GuideAPA EWCG (2011) Engineered Wood Construction Guide: Building Requirements and Related Panel SystemsAPA PS 1 (2009) Structural Plywood (with Typical APA Trademarks)ASME INTERNATIONAL (ASME)ASME B18.6.1 (1981; R 2008) Woo

15、d Screws (Inch Series)ASTM INTERNATIONAL (ASTM)ASTM A1008/A1008M (2012a) Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy and High-Strength Low-Alloy with Improved Formability, Solution Hardened, and Bake HardenedASTM A167 (1999; R 2009) Standard Spec

16、ification for Stainless and Heat-Resisting Chromium-Nickel Steel Plate, Sheet, and StripASTM A325 (2010; E 2013) Standard Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile StrengthASTM A325M (2013) Standard Specification for Structural Bolts, Steel, Heat Treated, 8

17、30 MPa Minimum Tensile Strength (Metric)ASTM C1036 (2010; E 2012) Standard Specification for Flat GlassASTM D13 (2002) Standard Specification for Spirits of TurpentineASTM D4689 (2012) Standard Specification for SECTION 12 32 00 Page 4Provided by IHSNot for ResaleNo reproduction or networking permit

18、ted without license from IHS-,-,-Adhesive, Casein-TypeASTM D4690 (2012) Standard Specification for Urea Formaldehyde Resin AdhesivesASTM F594 (2009; E 2011) Standard Specification for Stainless Steel NutsASTM F836M (2002; R 2010) Standard Specification for Style 1 Stainless Steel Metric NutsBUILDERS

19、 HARDWARE MANUFACTURERS ASSOCIATION (BHMA)ANSI/BHMA A156.9 (2010) Cabinet HardwareCOMPOSITE PANEL ASSOCIATION (CPA)CPA A208.1 (2009) ParticleboardCPA A208.2 (2009) Medium Density Fiberboard (MDF) for Interior ApplicationsHARDWOOD PLYWOOD AND VENEER ASSOCIATION (HPVA)HPVA HP-1 (2009) American Nationa

20、l Standard for Hardwood and Decorative PlywoodKITCHEN CABINET MANUFACTURERS ASSOCIATION (KCMA)KCMA A161.1 (2000) Performance Notice 1) Bolt, Toggle: and Expansion Sleeve, ScrewFS FF-S-325 (Basic; Int Amd 3; Notices 3, 4) Shield, Expansion; Nail, Expansion; and Nail, Drive Screw (Devices, Anchoring,

21、Masonry)SECTION 12 32 00 Page 5Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-FS MM-L-736 (Rev D; Notice 1) Lumber; HardwoodFS MM-L-751 (Rev H) Lumber; SoftwoodFS TT-C-490 (Rev F; Am 1) Cleaning Methods for Ferrous Surfaces and Pretreatments for Org

22、anic CoatingsFS TT-C-520 (Rev B; Notice 1) Coating Compound, Bituminous, Solvent Type, Underbody (for Motor Vehicles)FS TT-E-489 (Rev J; Notice 2) Enamel, Alkyd, Glass, Low VOC ContentFS TT-E-491 (Rev C; Notice 1) Enamel; Gloss, Synthetic (for Metal and Wood Furniture)FS TT-F-336 (Rev E; Notice 1) F

23、iller, Wood, PasteFS TT-V-121 (Rev H; Notice 1) Varnish, Spar, Water-ResistingFS WW-P-541 (Rev E; Am 1; Notice 1) Plumbing Fixtures1.2 SUBMITTALS*NOTE: Review Submittal Description (SD) definitions in Section 01 33 00 SUBMITTAL PROCEDURES and edit the following list to reflect only the submittals re

24、quired for the project.The Guide Specification technical editors have designated those items that require Government approval, due to their complexity or criticality, with a “G.“ Generally, other submittal items can be reviewed by the Contractors Quality Control System. Only add a “G” to an item, if

25、 the submittal is sufficiently important or complex in context of the project.For submittals requiring Government approval on Army projects, a code of up to three characters within the submittal tags may be used following the “G“ designation to indicate the approving authority. Codes for Army projec

26、ts using the Resident Management System (RMS) are: “AE“ for Architect-Engineer; “DO“ for District Office (Engineering Division or other organization in the District Office); “AO“ for Area Office; “RO“ for Resident Office; and “PO“ for Project Office. Codes following the “G“ typically are not used fo

27、r Navy, Air Force, and NASA projects.Choose the first bracketed item for Navy, Air Force and NASA projects, or choose the second bracketed item for Army projects.SECTION 12 32 00 Page 6Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-*Government appro

28、val is required for submittals with a “G“ designation; submittals not having a “G“ designation are for Contractor Quality Control approval.for information only. When used, a designation following the “G“ designation identifies the office that will review the submittal for the Government. Submit the

29、following in accordance with Section 01 33 00 SUBMITTAL PROCEDURES:SD-02 Shop DrawingsFabrication; G; G, _Installation Drawings; G; G, _SD-03 Product DataCabinets; G; G, _Corrosion-Resistant Steel; G; G, _Plywood; G; G, _Medium Density Fiberboard (MDF); G; G, _Hardwood; G; G, _Hardwood Plywood; G; G

30、, _Glass; G; G, _Adhesives; G; G, _Filler Material; G; G, _Particle Board; G; G, _Turpentine; G; G, _Varnish; G; G, _Fasteners; G; G, _Steel Sinks; G; G, _Service Fixtures; G; G, _Accessories and Hardware; G; G, _Softwoods; G; G, _Plastic Laminate; G; G, _Countertops; G; G, _SD-04 SamplesAccessories

31、 and Hardware; G; G, _SECTION 12 32 00 Page 7Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Manufacturers Standard Color Charts; G; G, _SD-07 CertificatesCorrosion-Resistant Steel; G; G, _Plywood; G; G, _Hardwood; G; G, _Glass; G; G, _Adhesives; G;

32、G, _Filler Material; G; G, _Particle Board; G; G, _Turpentine; G; G, _Varnish; G; G, _Fasteners; G; G, _Steel Sinks; G; G, _Service Fixtures; G; G, _Accessories and Hardware; G; G, _SD-08 Manufacturers InstructionsManufacturers Instructions; G; G, _1.3 MAINTENANCE MATERIAL SUBMITTALSSubmit manufactu

33、rers instructions for wood and metal cabinet systems including special provisions required to install equipment components and system packages. Special notices to detail impedances, hazards and safety precautions.1.4 QUALITY ASSURANCESubmit manufacturers standard color charts for wood and metal cabi

34、nets showing the manufacturers recommended color and finish selections.1.5 DELIVERY, STORAGE, AND HANDLINGDeliver, handle, and store cabinets in a manner that prevents damage or deformity. Provide temporary skids under units weighing more than _ kilogram pounds.PART 2 PRODUCTS2.1 SYSTEM DESIGNProvid

35、e wood cabinets, factory-fabricated and finished in the manufacturers standard sizes and finishes of the type, design, and configuration indicated. Construct cabinets as specified meeting the SECTION 12 32 00 Page 8Provided by IHSNot for ResaleNo reproduction or networking permitted without license

36、from IHS-,-,-requirements of KCMA A161.1. Wall and base cabinet assemblies to consist of individual units joined into continuous sections. Use fastenings that permit removal and replacement of individual units without affecting the remainder of the installation. Provide counters with watertight sink

37、 rim when indicated, and removable drawers equipped with position stops to avoid accidental complete withdrawals. Fix or adjust shelves as indicated.2.2 FABRICATION2.2.1 Wood Cabinet FabricationConstruct wall and base cabinets with frame fronts and solid ends, or frame construction throughout. Provi

38、de 20 by 40 millimeter 3/4-by 1-1/2-inch kiln-dried hardwood framing members, using mortise and tenon, dovetailed, grove and lapped, biscuit and dado, or doweled, with glue assembly. Brace top and bottom corners with hardwood blocks that are glued with water-resistant glue and nailed in place. Provi

39、de base cabinets with an integral toe space at least 65 millimeter 2-1/2 inches deep and 100 millimeter 4-inches high. Mount drawers on metal guides hardwood guides renewable plastic fiber guides. Provide fixed removable and adjustable shelving, as indicated.Minimum thicknesses of materials for fram

40、e-front, solid-end cabinet construction is as follows:a. Backs and bottoms of base cabinets and tops of wall cabinets: 3 millimeter 1/8-inch tempered hardboard. Brace bottoms with wood members glued in place.b. Cabinet ends: 15 millimeter 1/2-inch hardwood-veneer plywoodc. Doors: 20 millimeter 3/4-i

41、nch hardwood softwood plywood, solid hollow core doorsd. Drawer fronts: 20 millimeter 3/4-inch hardwoode. Drawer bottoms: 4.76 millimeter 3/16-inch plywood or tempered hardboard. Drawer bottoms over 380 millimeter 1 foot 3 inches wide will be braced with wood members glued in place.f. Drawer sides a

42、nd backs: 15 millimeter 1/2-inch hardwoodg. Interior partitions or dividers: 15 millimeter 1/2-inch fir plywood, Grade A-A hardwoodh. Shelves: Grade A-B plywood, supported on ends and 600 millimeter 24 inches on centersi. Adjustable shelves: 20 millimeter 3/4-inch plywoodj. Base cabinet shelves: 16

43、millimeter 5/8-inch plywoodk. Wall cabinet shelves: 15 millimeter 1/2-inch plywood glued-up solid wood 6 millimeter 1/4-inch plywood with a solid-wood frameMinimum thicknesses of materials for frame-type cabinet construction is as follows:a. Cabinet ends: 6 millimeter 1/4-inch hardwood plywoodSECTIO

44、N 12 32 00 Page 9Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-b. Backs, bottoms, partitions, and dividers: 4 millimeter 3/16-inch tempered hardboard in a frameProvide materials for other components as specified.2.2.1.1 High-Pressure Decorative Laminate (HPDL)ANSI/NEMA LD 3, satin finish, unless otherwise indicated.2.2.1.1.1 CountertopsPF 42, satin finish.2.2.1.1.2 Vertical SurfacesGP 28 or PF 30, satin finish.2.2.1.1.3 Backing SheetBK 20.2.2.1.1.4 Cabinet LinerCL 20.2.2.