PPI TN-4-2015 Odorants In Plastic Fuel Gas Distribution Systems.pdf

《PPI TN-4-2015 Odorants In Plastic Fuel Gas Distribution Systems.pdf》由会员分享，可在线阅读，更多相关《PPI TN-4-2015 Odorants In Plastic Fuel Gas Distribution Systems.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 Odorants In Plastic Fuel Gas Distribution Systems TN-4/2015 Foreword This report was developed and published with the technical help and financial support of the members of the PPI (Plastics Pipe Institute, Inc.). The members have shown their interest in quality products by assisting independent st

2、andards-making and user organizations in the development of standards, and also by developing reports on an industry-wide basis to help engineers, code officials, specifying groups, and users. The purpose of this Technical Note is to provide recommendations for the use of odorants in gas pipelines t

3、hat are manufactured of plastic materials. This report has been prepared by PPI as a service of the industry. The information in this report is offered in good faith and believed to be accurate at the time of its preparation, but is offered “as is” without any express or implied warranty, including

4、WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Any reference to or testing of a particular proprietary product should not be construed as an endorsement by PPI, which does not endorse the proprietary products or processes of any manufacturer. The information in this report is of

5、fered for consideration by industry members in fulfilling their own compliance responsibilities. PPI assumes no responsibility for compliance with applicable laws and regulations. PPI intends to revise this report from time to time, in response to comments and suggestions from users of the report. P

6、lease send suggestions of improvements to the address below. Information on other publications can be obtained by visiting the web site. The Plastics Pipe Institute, Inc. www.plasticpipe.org This Technical Note, TN-4, was first issued in 1971 and was revised in 1998, 1999, 2000, 2009, and June 2015.

7、 Copyright, The Plastics Pipe Institute, Inc. 2015 ODORANTS IN PLASTIC FUEL GAS DISTRIBUTION SYSTEMS 1. INTRODUCTION To enhance safety, the fuel gas industries add chemical compounds, with a unique odor, to alert the user if a leak occurs. This odor is designed to be readily detectable by smell when

8、 the fuel gas reaches a concentration in air of one-fifth of the lower explosive limit. CFR 192, Minimum Federal Safety Standards, paragraph 192.625 establishes requirements for odorization of fuel gases supplied through regulated distribution systems. National Fire Protection (NFPA) Bulletins, No.

9、58: Storage and Handling of Liquefied Petroleum Gases, and No. 59: Liquefied Petroleum Gases at Utility Gas Plants provide the requirements for odorization of LP Gas and LP-Air gases. For detailed information on current regulations review these documents. The compounds used as odorants usually consi

10、st of aliphatic mercaptans, such as propyl and tertiary butyl mercaptan, and sulfides, such as thiophene or dimethyl sulfide at ordinary temperatures. Most gas odorants are liquids at full concentrations under ambient conditions, and, in this state, might be harmful to some plastic pipe materials. H

11、owever, in the concentrations typically needed to odorize the gas being transported and distributed by pipeline, they are in the vapor state and cause no harm to plastic piping. 2. SCOPE This technical note provides recommendations when using odorants in fuel gas systems that contain plastic pipelin

12、es in whole or in part. 3. PROCEDURE The mercaptans and sulfides used as odorants are liquid hydrocarbons. Liquid hydrocarbons, in sufficient concentration, can swell and soften most plastic pipe materials. The appearance and fusibility of the plastic pipe may also be affected due to odorant saturat

13、ion. Odorants should never be introduced into a plastic pipe system in a concentrated liquid state. Also, liquid odorants in concentrate form should not be used to locate leaks in plastic pipelines. Odorants are typically carefully introduced either at odorization stations or, in some cases, by dire

14、ct injection of small amount into the distribution main in a liquid form which quickly vaporizes and mixes with the gas stream. Concentrations, in the gaseous form, should be low enough to prevent condensation at the lowest temperature and/or the highest pressure encountered in the system. When odor

15、ants are injected at nominal rates the concentration rarely exceeds 25 parts per million by weight in gaseous form. It must achieve a level in air of one-fifth of the lower explosive limit of natural gas to comply with Federal requirements. At this concentration, odorants are not harmful to plastic

16、pipe. Odor fade is unlikely to occur in plastic pipe systems due to the inert nature of plastic. If odor fade is a concern in plastic gas mains and service lines, as is possible in dead end mains made from steel, it may be necessary to pre-treat the piping with odorant in the same manner normally used to saturate mill scale and rust in steel pipe. If odor fade is noticed in plastic gas mains and service lines, additional odorants should be introduced in vapor phase, preferably in the gaseous form.