NAVY MIL-T-1368 C (4)-2000 TUBE AND PIPE NICKEL-COPPER ALLOY SEAMLESS AND WELDED《铜镍合金无缝焊接管》.pdf
《NAVY MIL-T-1368 C (4)-2000 TUBE AND PIPE NICKEL-COPPER ALLOY SEAMLESS AND WELDED《铜镍合金无缝焊接管》.pdf》由会员分享,可在线阅读,更多相关《NAVY MIL-T-1368 C (4)-2000 TUBE AND PIPE NICKEL-COPPER ALLOY SEAMLESS AND WELDED《铜镍合金无缝焊接管》.pdf(4页珍藏版)》请在麦多课文档分享上搜索。
1、MIL-T-1368C Amendment 4 (SH) 12 December 2000 SUPERSEDING INT . AMENDMENT 3 (SH) 24 December 1980 USED IN LIEU OF AMENDMENT 2 21 February 1966 MILITARY SPECIFICATION TUBE AND PIPE, NICKEL-COPPER ALLOY, SEAMLESS AND WELDED This amendment is issued for use by the NAVAL SYSTEMS COMMAND, with Military S
2、pecification MIL-T-l368C, dated 2 June 1965. PAGE 6 Paragraph 3.5 Add after last sentence: “Pipe and tubes shall be specified in two dimensions only; for example, an outside diameter and average wall, or as inside diameter and average wall.” PAGE 7 4.1 Delete and substitute: “4.1 Responsibility for
3、inspection. Unless otherwise specified in the contract, the contractor is responsible for the performance of all inspection requirements as specified herein. Except, as otherwise specified in the contract, the contractor may use his own or any other facilities suitable for the performance of the ins
4、pection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. 4.1.1 Certif
5、ication of quality compliance. A certificate of quality compliance shall be prepared for each lot of material offered for acceptance (see 6.2.1). The certificate shall include actual data of specified chemical and mechanical tests. Qualitative results of nondestructive tests and other inspections or
6、 tests shall be recorded on the certificate. The certificate shall also state that each lot has been sampled, tested, and inspected in accordance with the specification and meets all specification requirements. The certificate shall be signed by a responsible representative of the contractor. “ Page
7、 1 of 4 FSC 4710 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-1368C Amendment 4 (SH) PAGE 8 Paragraph 4.3.2.1, line three: Insert a period after the word “analysis“, and delete, “approved by the contracting officer (see 6.2) .“ Paragraph 6.2
8、 (i) : Delete the line in its entirety. *Add the following: 6.2.1 Data requirements. When this specification is used in a procurement which incorporates a DD Form 1423 and invokes the provisions of 7-104.9(n) of the Defense Acquisition Regulations, the data requirements identified below will be deve
9、loped as specified by the Data Item Description (DD Form 1664) and delivered in accordance with the approved Contract Data Requirements List (DD Form 1423) incorporated into the contract. When the provisions of DAR 7- 104.9(n) are invoked, the procurement document will specify that the data specifie
10、d below is to be delivered by the contractor (use of the DID in this case is not required). Deliverable data required by this specification is cited in the following paragraph: PARAGRAPH DATA REOUIREMENT APPLICABLE DID 4.1.1 Certification of UDI-A-23264 Quality Compliance Certification Data/ Report
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- NAVYMILT1368C42000TUBEANDPIPENICKELCOPPERALLOYSEAMLESSANDWELDED 镍合金 无缝 焊接 PDF

链接地址:http://www.mydoc123.com/p-982489.html