NAVY MIL-STD-1323-388-1993 UNIT LOAD FOR UNDERWAY REPLENISHMENT FUZE FMU-143E B IN PA60 CONTAINER《FMU-143E B IN PA60容器导火管航行的负载》.pdf

《NAVY MIL-STD-1323-388-1993 UNIT LOAD FOR UNDERWAY REPLENISHMENT FUZE FMU-143E B IN PA60 CONTAINER《FMU-143E B IN PA60容器导火管航行的负载》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-STD-1323-388-1993 UNIT LOAD FOR UNDERWAY REPLENISHMENT FUZE FMU-143E B IN PA60 CONTAINER《FMU-143E B IN PA60容器导火管航行的负载》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-STD-1323 -388 = LL 0498b83 313 M,L-STD-,323-388 MILITARY STANDARD UNIT LOAD FOR UNDERWAY REPLENISHMENT IN PA60 CONTAINER FUZE, FMU-I43E/B (NAWI 19MAY lQ93 - NUMBER OF FUZES PER CONTAINER 2 NUMBER OF CONTAINERS PER UNIT LOAD NUMBER OF FUZES PER UNIT LOAD . 112 GROSS WEIGHT OF ONE CONTAINER . .21

2、LBS TARE WEIOHT OF ONE CONTAINER .7 LBS WEIGHT OF WOOD WNNAGE (APPOX.) . .59 LBS WEIGHT OF STEEL STRAPPING (APPROX ) WEIGHT OF STEEL PALLET .94 LBS GROSS WEIGHT OF UNIT LOAD 1.337LBS + CUBE 410CUFT .% 8 LBS FOR HAZARD CLASSIFICATION SEE SWo20-AC-sAF-G10/020/030 + DO NOT USE FOR SHIPPING WEIGHT T.O.

3、11A7-32-7 Do NOT STACK MORE THAN 4 UNiT LOADS HIGH IN STORAGE. TEST REPORT NUMBER 93052 , . AMSC NO. - N/A Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. . i . . !ALLETIUN6 PROCEDURE 4) CONSTRUCT END ASSEWES AS SHOWN IN DElAILC AND C 3) THREAD ONE

4、 10NGITlIDINAl STRAP ITFM 3, RFMIEEN THE 5th rrND 6th WIRES OF PALLET DECK, ITEM I. AS SHOWN IN DETAIL A REPEAT ON OPWSITE SIDE OF PALLET DECK 1HREAO A THIRD LONGITUDINAL STRAP. ITEM 3. BtTWEEN THE 111 ti AND lZ1H WIRE OF THE PALLET DECK. IfEM 1. AS SHOW IN DETAIL A. C POClTlOtJ DECK PANEL. ITEM 2,

5、ON PALLET DECK D) POSITION 56 CONTAINERS ON DECK PANEL, IlEM 2, AS SHOWN WITH EOUAL OVERHANG ON BOTH SIDES OF THE UNIT LOAD. BE SURE ALL Of THE CLOSURE UTCHES FACE THE SAME DIRECTION SEE SPECIAL NOTES ON PAGE 3 CONCERNING PARTIAL LAYERS OR UNIT Lmm E) POSITION COVER PANEL, ITEM 2. OVER TOP OF UNIT L

6、OAD n POSITION UTEAL STRIPPING. ITEM 4. UNDER THE PALLET DECK AND AROUND THE UN17 LOAD. TENSION AND SECURE UCH STRAP WITH ONE DOUBLE NOTCHED SEAL. ITEM 5 SECURE EACH STRAP WITH ONE DOUBLE NOTCHED SEAL, ITEM 5 10) HOLDING APPROPRIATE END ASSEMBLIES IN PLACE AS SHOWN, POSITION LONGITUDIWL STRAPS. ITEM

7、 3. WER THE UNIT LW TENSION *ND (H) At i STRAPPING SHALL BE STAPLED TO COMR PANELS. ITEM 2. IN LOCATIONS SHOWN WITH 3/4 STRAPPI% STAPES. nm 9. MARKING. IN AODITION TO ANY SPECIAl MARKING REOUIRED BY CONTRACT OR ORMR. THE UNm LOAD SHAU BE MARKED IN ACCORDMCE Wlf“ MIL-STD- WW , , KPALLETJZIN 6 PROCEDU

8、RE: (A) REMOVESAWS IA CUT AND REMOVE ALL STRAPPING AND LUMBER Ir (s) REMOVE CONTAINERS END ASSEMBLY - SEE DETAIL C I - -._ I 33 l I I t REF li Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STO-1 323-388 (NAVY 1 DETAIL 0 TO BE USED ON END OF UNI

9、T LOAD W/TH CLOSURE LATCHES I AC11 N HAI ILN!; III MS I ANI) ii 10 I NI) PANII IILM i;. Wllii NAUS AN1/00 CIAI1f.S ANY IIWlRUDINCi NAII O11 SIAILI LNIPS CHAI I RF Ci INCtiFD OVC I3 14 REF . To BE USED ON END OF UNIT LOAD wmour CLOSURE LATCHES d REF R PL SPECIAL NOTES FOR PARTIAL LAYERS UNIT LOAD (A)

10、 WHEN THERE ARE NOT ENOUGH LOADED CONTAINERS TO COMPLETE A LAYER (28 CONTAINERS), EMW CONTAINERS MAY BE USED TO FILL IN THE VOID SPACES (81 EMPN CONTAINERS SHALL BE POSITIONED AT THE CENTER OF THE UYER IN ORDER THAT THE UNIT LOADS CENTER OF GRAWTY REMAINS AS CLOSE TO THE CENTER OF THE PALLET AS POSS

11、IBLE DETAIL D SHOWS. AS AN EXAMPLE. THE REQUIRED CONFIGURATION WHEN SIX EMPTY CONTAINERS ARE NEEDED TO COMPLETE A LAYER (C) IN A TWO-LAVER HIGH UNIT LOAD, EMPTY BOXES SHALL ONLY BE PLACED IN THE UPPER LAYER (0) EMPN BOXES SHALL BE CLEARLY MARKED THAT THEY ARE EMPTY DETAIL 0 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-