NAVY MIL-S-24584-1978 STOPPERS CARPENTER AND ASSOCIATED BRIDLES (WIRE ROPE AND CHAIN LINK)《竖式离心和其他限制物(钢丝绳和链环)》.pdf

《NAVY MIL-S-24584-1978 STOPPERS CARPENTER AND ASSOCIATED BRIDLES (WIRE ROPE AND CHAIN LINK)《竖式离心和其他限制物(钢丝绳和链环)》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-S-24584-1978 STOPPERS CARPENTER AND ASSOCIATED BRIDLES (WIRE ROPE AND CHAIN LINK)《竖式离心和其他限制物(钢丝绳和链环)》.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-S-2454 r 40 m 777770b OLOLlLb 2 r-O/-Z After final proof load testing (see 3.3.2), each carpenter stopper and brldle assembly s all be inspected for conformance with 3.3.4. rope shall be inspected for conformance with 3.3.5. The gripped wire 4.3 Acceptance criteria. 4.3.1 Parts not meeting the r

2、equirements of this specification shall be rejected. 4.3.2 In addition to all other requirements, all tests shall be witnessed by a Govern- Retesting shall not be permitted. ment representative. 4 4 Ins ection of re aration for deliver The preservation-packaging, packing, and markin; sha* e inspecte

3、 - for compliance wit e requirements of section 5 of this specifi- cation; Licensed by Information Handling ServicesMXL-S-24584 (SH) 5r PREPARATION FOR DELIVERY (The preparation for delivery requirements specified herein apply only for direct Govern- ment acquisitions, For the extent of applicabilit

4、y of the preparation for delivery require- ments of referenced documents listed in section 2, see 6.3.) 5,1 Preservation-packaging. The preservation-packaging shall be level A or C, as specified lsee 6.2.1) 5,l.L.l Disassembl . Disassembly shall be confined to the removal of parts and comp- ncnbs-th

5、at: wouwe increase cubage, such as the bridle assembly that can be removed anii reinstalled without the use of special tools. packaged to afford protection against deterioration and damage ran the supply source to the inal destination including storage. Exposed unprotected metal surfaces of the carp

6、enter stopper and bridle assemblies requiring the application of a contact preservative in accord- ance with MIL-P-116 shall be cleaned, dried and coated with type P-1 or P-19 preservative conforming to the applicable cpecif ication listed in and applied in accordance with MIL-P-116. 5.1.1.2 Preserv

7、ative, The carpenter stoppers and bridle assemblies shall be preserved- 5.1.1.3 Packagin(t. 51.2 Level C. The carpenter stopper and bride assemblies shall be preserved-packaged Packaging of carpenter stopper and bridle assemblies is not required. to afford pretsctizn against deterioration and damage

8、 from the supply source to the initial destination. The contractor may use his standard practice providing it fulfills these re- quirements. 5.2 Paekinz. Packing shail be level A, B, or C as specified (see 6.2.1). 5.2.1 Lavol A/D. The carpenter stopper and bridle assemblies preserved-packaged as spe

9、cified (see S.2x shall be individually packed in woad or wood-cleated boxes conforming to PPP-B-621, class 2, 81: PPP-B-601, overseas, type. Container selection and box style shall bn, at tho option of the contractor, Interior blocking, bracing and anchoring to prevent movement: of tho asuembly with

10、in the box shall be in accordance with MEL-STD-1186. Box closure and flat strapping shall bo in accordance with the appendix to the applicable box specification. 5.2.2 Level c. The carpenter stopper and bridle assemblies preserved-packaged as specified (6=2,1), shall be packed in a manner to assure

11、carrier acceptance and safe delivery to daotinatisn at the lowest ratings of the carrier in compliance with Uniform Froight: CLanaification Rules or with National Motor Freight Classification Rules. aesembliaa, praaerved-packaged, and packed as specified herein for level A or CI shall be palletized

12、in accordance with NIL-STD-147, load type, as applicable. 5.2.3 FA1lotization. When specified (see 6.2.1) I the carpenter stopper and bridle 5.3 HarkLn In addition to any special marking required by the contract, (see 6.2.1) packages, + e lipping containers, and palletized loads, shall be marked in

13、accordance with SIIL-STR-129 6. NOTES 6.1 Intended use. Carpenter stoppers and associated bridle assemblies provide a means of gripping and Iioliffnll wire rope under load (see NAVCEA 0994-LP-000-3010 , 0994-LP-000-3020 , and 0994-LP-004-8010 for typical Navy use). strand right regular= type Ir gene

14、ra1 purpose, class 3, drawn galvanized or uncoated wire rope in accordance with RR-W-4 10. stoppers hav&c&S percent less than the lead of the carpenter stoppers wedge block halix, rope sizes 6.1.1 Gripped wire rs. Carpenter stoppers are designed for gripping and holding 6- 6.1.2 -Gri ed ro e pitch.

15、It is recommended that wire rope used with carpenter Additionally, the following table is furnished or the most frequently used wire 8 Licensed by Information Handling ServicesI MIL-S-24584 40 7777706 0104824 L M I 1-5/8 2 -1/4 2-1/2 5-53 16.875 16.250 6.2 Orderinq data. (a) Title, number and date o

16、f this specification. id) Gvernment furnished equipment, as required (see 3.6). (e) Whether the carpenter stopper (s) and associated bridle assembly shall be packaged levei A or C or packed level A/B .or C (see 5.1 and 5.2). (f) Palletization , if required (see 5.2.3) . (9) Special marking required

17、(see 5.3). the data-identified belo#, which are required to be developed by the contrctor, as specified on an approved Data Item Description (DD Form 1664), and which are required to be delivered to the Government. should be selected and SDecified on the aDDrOVed Contract Data Require- developed by

18、the contractor and required to be delivered to the Government should be selected from the list below and specified in the contract. Paragraph Data requirements Applicable DID Option 4.1.1 Certification data/report UD1 -A -2 3 2 6 4 - (Cories of data item descriptions required by the contractors in c

19、onnection with speci- invitation for bids or request for proposal shall apply.) 6.2.2.1 The data requirements of 6.2.2 and any task in section 3, 4, or 5 of the specification required to be performed, to meet a data requirement may be waived by the contracting/acquisition activity upon certification

20、 by the offeror that identical data were sutanitted by the offeror and accepted by the Government under a previous contract for identi- cal item acquired to this specification. This does not apply to specific data which may be required for each contract regardless of whether an identical item has been supplied previously (for example, test reports). by the contractor for incorporation into the equipment and lose their separate identity when the equipment is shipped. Preparing activity: *V.S. GOVERNMENT PRINTING OFFICE: 1978603-022134 9 Licensed by Information Handling Services