NAVY MIL-E-81512 (1)-1987 ENCODERS SHAFT POSITION TO DIGITAL CONTACT TYPE ALTITUDE REPORTING GENERAL SPECIFICATION FOR《一般规格数字轴转移接触式编码器海拔报告》.pdf

《NAVY MIL-E-81512 (1)-1987 ENCODERS SHAFT POSITION TO DIGITAL CONTACT TYPE ALTITUDE REPORTING GENERAL SPECIFICATION FOR《一般规格数字轴转移接触式编码器海拔报告》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-E-81512 (1)-1987 ENCODERS SHAFT POSITION TO DIGITAL CONTACT TYPE ALTITUDE REPORTING GENERAL SPECIFICATION FOR《一般规格数字轴转移接触式编码器海拔报告》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、MI L-E-81512 AMENDMENT 1 10 April 1987 MILITARY SPECIFICATION ENCODER, SHAFT ANGLE TO DIGITAL, CONTACT TYPE, ALTITUDE REPORTING; GENERAL SPECIFICATION FOR This amendment forms a part of military specification MIL-E-81512 dated 18 December 1968, and is approved for use by all Departments and Agencies

2、 of the Department of Defense. PAGE 4 3.2 Qualification. Delete and substitute the following: “3.2 First article. When specified in the contract or purchase order, a samle shall be sub.jected to first article inspection (see 4.3.1 and PAGE 13 4.3 Classification of tests. Delete “(a) Qualification“ a

3、nd substitute “(a) First 4.3.1 Qualification inspection. Delete and substitute the following: “4.3.1 First article. First article inspection sha laboratory acceptable to the Government (see 6.3) on produced with equipment and procedures normally used art i c 1 e. I 1 be performec at a sample units i

4、n production.“ , 4.3.1.1. Samples. Delete and substitute the following: “4.3.1.1 Samples. Samples submitted for first article testing shall be representam the manufacturer s normal producti.on. The first article test sample shall consist of a minimum of three (3) encoders, submitted as directed by t

5、he procuring activity.“ AMSC N/A FSC 5990 DISTRIBUTION STATEMENT A: Approved for public release; distribution is un1 imited. 1 of 2 . Licensed by Information Handling ServicesMI L-E-81512 AMENDMENT 1 PAGE 14 I 4.3.1.2 Test routine. I Change the word “qualification“ to “first article.“ 4.3.1.3 Change

6、s. Delete and substitute the following: “4.3.1.3 Changes. After samples have been submitted for first article testing, no changes shall be made in the materials, design, or manufac- turing processes without prior approval of the procuring activity.“ TABLE IV. Qualification Tests I Change table headi

7、ng from “Qualification Tests“ to “First Article Tests.“ PAGE 18 4.4.11.1 Electrical noise No, 1. I Change the word “qualification“ to “first article.“ PAGE 26 Add the following new paragraph: “6.3 First article. When a first article inspection is required, the item should be a first article sample a

8、s specified in 4.3.1.1. tracting officer should include specific instructions in acquisition documents regarding arrangements for examinations, approval of first article test results, and disposition of first articles. Invitation for bids should provide that the Government reserves the right to waiv

9、e the requirement for samples for first article inspection to those bidders offering a product which has previously been acquired or tested by the Government, and that bidders offering such products, who wish to rely on such production or test, must furnish evidence with the bid that prior Government approval is presently appropriate for the pending contract.“ The con- Custod i ans : Army - AR . Navy - AS . Air Force - 85 Review activities: Army - Navy - Air Force - DLA - ES r Preparing activity: Navy - AS (Project 5990-0331 ) 2 Licensed by Information Handling Services