ASTM F1863-2016 Standard Test Method for Measuring the Night Vision Goggle-Weighted Transmissivity of Transparent Parts《用于测量透明部件的夜视镜加权透射率的标准试验方法》.pdf
《ASTM F1863-2016 Standard Test Method for Measuring the Night Vision Goggle-Weighted Transmissivity of Transparent Parts《用于测量透明部件的夜视镜加权透射率的标准试验方法》.pdf》由会员分享,可在线阅读,更多相关《ASTM F1863-2016 Standard Test Method for Measuring the Night Vision Goggle-Weighted Transmissivity of Transparent Parts《用于测量透明部件的夜视镜加权透射率的标准试验方法》.pdf(6页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: F1863 16Standard Test Method forMeasuring the Night Vision Goggle-Weighted Transmissivityof Transparent Parts1This standard is issued under the fixed designation F1863; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, t
2、he year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.INTRODUCTIONTest Methods D1003 and F1316 apply to the transmissivity measurement of transparent materials,the former be
3、ing for small flat samples, and the latter for any materials including larger, curved piecessuch as aircraft transparencies. Additionally, in Test Method D1003, the transmissivity is measuredperpendicular to the surface of test sample and both test methods measure only in the visible lightspectral r
4、egion. Night vision goggles (NVGs) are being used in aircraft and other applications (forexample, marine navigation, driving) with increasing frequency. These devices amplify both visibleand near-infrared (NIR) spectral energy. Overall visual performance can be degraded if the observeruses the NVGs
5、while looking through a transparency that has poor transmissivity in the visible andNIR spectral regions. This test method describes both direct and analytical measurement techniquesthat determine the NVG-weighted transmissivity of transparent pieces including ones that are large,curved, or held at
6、the installed position.1. Scope1.1 This test method covers apparatuses and procedures thatare suitable for measuring the NVG-weighted transmissivity oftransparent parts including those that are large, thick, curved,or already installed. This test method is sensitive to transpar-encies that vary in t
7、ransmissivity as a function of wavelength.1.2 Since the transmissivity (or transmission coefficient) is aratio of two radiance values, it has no units. The units ofradiance recorded in the intermediate steps of this test methodare not critical; any recognized units of radiance (for example,watts/m2-
8、str) may be used, as long as it is consistent.21.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regu
9、latory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:3D1003 Test Method for Haze and Luminous Transmittanceof Transparent PlasticsE177 Practice for Use of the Terms Precision and Bias inASTM Test MethodsE691 Practice for Conducting an Interlaboratory Study toDetermine the Precis
10、ion of a Test MethodF1316 Test Method for Measuring the Transmissivity ofTransparent Parts3. Terminology3.1 Definitions:3.1.1 analytical test method, nthe test method that usesspectral transmissivity data of a transparent part collected bythe use of either spectrophotometric or spectroradiometricins
11、trumentation. The data are then examined using analyticmethods to determine the NVG-weighted transmissivity of thepart.1This test method is under the jurisdiction of ASTM Committee F07 onAerospace and Aircraft and is the direct responsibility of Subcommittee F07.08 onTransparent Enclosures and Mater
12、ials.Current edition approved April 1, 2016. Published April 2016. Originallyapproved in 1998. Last previous edition approved in 2010 as F1863 10. DOI:10.1520/F1863-16.2RCA Electro-Optics Handbook, RCA/Solid State Division/Electro Optics andDevices. Technical Series EOH-11. Lancaster, PA; 1974.3For
13、referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700,
14、West Conshohocken, PA 19428-2959. United States13.1.2 direct test method, nthe test method that uses theactual luminous output, as measured by a photometer, properlycoupled to the eyepiece of the test NVG. The NVG-weightedtransmissivity of the part is then determined by forming theratio of the NVG o
15、utput luminance with the transparent part inplace to the luminance output without the part.3.1.3 NVG-weighted spectral transmissivity, nthe spectraltransmissivity of a transparent part multiplied by the spectralsensitivity of a given NVG (see Fig. 1).3.1.4 NVG-weighted transmissivity (TNVG), nthe sp
16、ectraltransmissivity of a transparent part multiplied by the spectralsensitivity of a given NVG integrated with respect to wave-length (see Fig. 1, Eq 1 and Eq 2).3.1.5 NVG spectral sensitivity, nthe sensitivity of an NVGas a function of input wavelength.3.1.6 photometer, na device that measures lum
17、inous in-tensity or brightness by converting (weighting) the radiantintensity of an object using the relative sensitivity of the humanvisual system as defined by the photopic curve.2,43.1.7 photopic curve, nthe photopic curve is the spectralsensitivity of the human eye for daytime conditions as defi
18、nedby the Commission Internationale dEclairage (CIE) 1931standard observer.2,43.1.8 transmission coeffcient, nsee transmissivity.3.1.9 transmissivity, nthe transmissivity of a transparentmedium is the ratio of the luminance of an object measuredthrough the medium to the luminance of the same objectm
19、easured directly.4. Summary of Test Method4.1 General Test ConditionsThe test method shall beperformed in light-controlled area (for example, light-tightroom, darkened hangar, or outside at night away from stronglight sources). The ambient illumination must be very lowbecause of the extreme sensitiv
20、ity of the NVGs.Afixture holdsthe NVG and its objective lens is aimed at and focused on atarget. The target shall be either an evenly illuminated white,diffusely reflecting surface or a transilluminated screen (light-box). The illumination is provided by a white, incandescentlight source. Handle the
21、 samples carefully so as not to causeany damage. Do not clean them with any solvents. Usepart-specific, prescribed cleaning materials and methods.4.1.1 Direct Test MethodAttached directly to the eyepieceof the NVG is a photodetector. The measured field of view(FOV) shall be smaller than the uniforml
22、y illuminated portionof the target. The target illumination is adjusted so that theoutput of the NVGs is about 1.7 cd/m2(0.5 fL). This ensuresthat the NVG input level is sufficiently low that it does notactivate the NVG automatic gain control (AGC) circuitry. Theluminance output of the NVG is measur
23、ed with no transpar-ency in place and then repeated with the transparent material inplace between the light source and the NVG. The transmissiv-ity is equal to the NVG output luminance with the transparentmaterial in place divided by the NVG output luminancewithout the material (see Eq 1). The resul
24、t is the NVG-weighted transmissivity (TNVG) of the transparent material.4.1.2 Analytical Test MethodWithout the sample in place,measure the light sources spectral energy distribution from450 through 950 nm in 5-nm incremental steps. Place thesample into the spectrophotometer or spectroradiometer fix
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMF18632016STANDARDTESTMETHODFORMEASURINGTHENIGHTVISIONGOGGLEWEIGHTEDTRANSMISSIVITYOFTRANSPARENTPARTS
链接地址:http://www.mydoc123.com/p-535883.html