ASTM F1866-2007 Standard Specification for Poly (Vinyl Chloride) (PVC) Plastic Schedule 40 Drainage and DWV Fabricated Fittings《聚氯乙烯塑料壁厚40排水管和DWV加工配件的标准规范》.pdf
《ASTM F1866-2007 Standard Specification for Poly (Vinyl Chloride) (PVC) Plastic Schedule 40 Drainage and DWV Fabricated Fittings《聚氯乙烯塑料壁厚40排水管和DWV加工配件的标准规范》.pdf》由会员分享,可在线阅读,更多相关《ASTM F1866-2007 Standard Specification for Poly (Vinyl Chloride) (PVC) Plastic Schedule 40 Drainage and DWV Fabricated Fittings《聚氯乙烯塑料壁厚40排水管和DWV加工配件的标准规范》.pdf(5页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: F 1866 07An American National StandardStandard Specification forPoly (Vinyl Chloride) (PVC) Plastic Schedule 40 Drainageand DWV Fabricated Fittings1This standard is issued under the fixed designation F 1866; the number immediately following the designation indicates the year oforiginal
2、adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers requirements and test methodsfor fabricat
3、ed poly(vinyl chloride) (PVC) plastic schedule 40drainage and DWV fittings to be used with piping manufac-tured in accordance with Specification D 2665, D 1785, orF 891. These fabricated fittings are manufactured from pipe, orfrom a combination of pipe and injection molded parts.1.2 The requirements
4、 of this specification are to providefabricated PVC fittings suitable for drainage and venting ofsanitary waste systems, storm water systems, and certain otherliquid wastes. Fittings shall have solvent cement joints, gasketjoints or a combination thereof.1.3 The text of this specification references
5、 notes, footnotes,and appendixes that provide explanatory material. These notesand footnotes (excluding those in tables and figures) shall notbe considered as requirements of the specification.1.4 The values stated in inch-pound units are to be regardedas the standard. The values given in parenthese
6、s are providedfor information only.1.5 The following safety hazards caveat pertains only to thetest method portion, Section 10, of this specification. Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is the responsibility of the userof this stan
7、dard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.2. Referenced Documents2.1 ASTM Standards:2D 618 Practice for Conditioning Plastics for TestingD 1600 Terminology for Abbreviated Terms Relating toPlasticsD 1784 Specifica
8、tion for Rigid Poly(Vinyl Chloride) (PVC)Compounds and Chlorinated Poly(Vinyl Chloride)(CPVC) CompoundsD 1785 Specification for Poly(Vinyl Chloride) (PVC) Plas-tic Pipe, Schedules 40, 80, and 120D 2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD 2564 Specification for
9、 Solvent Cements for Poly(VinylChloride) (PVC) Plastic Piping SystemsD 2665 Specification for Poly(Vinyl Chloride) (PVC) Plas-tic Drain, Waste, and Vent Pipe and FittingsD 2855 Practice for Making Solvent-Cemented Joints withPoly(Vinyl Chloride) (PVC) Pipe and FittingsD 3212 Specification for Joints
10、 for Drain and Sewer PlasticPipes Using Flexible Elastomeric SealsF 412 Terminology Relating to Plastic Piping SystemsF 477 Specification for Elastomeric Seals (Gaskets) forJoining Plastic PipeF 656 Specification for Primers for Use in Solvent CementJoints of Poly(Vinyl Chloride) (PVC) Plastic Pipe
11、andFittingsF 891 Specification for Coextruded Poly(Vinyl Chloride)(PVC) Plastic Pipe With a Cellular CoreF 913 Specification for Thermoplastic Elastomeric Seals(Gaskets) for Joining Plastic Pipe3. Terminology3.1 Definitions: Definitions are in accordance with Termi-nology F 412, and abbreviations ar
12、e in accordance with Ter-minology D 1600, unless otherwise specified.4. Materials and Manufacture4.1 Basic MaterialsThe molded components for fabri-cated fittings shall be made of virgin or rework PVC com-pounds meeting or exceeding the requirements of Class 12454as defined in Specification D 1784.4
13、.1.1 The pipe shall be made of PVC that meets therequirements of the Materials Section of Specification D 1785or D 2665.4.2 GasketsElastomeric seals (gaskets) shall comply withthe requirements of Specification F 477 or F 913.1This standard is under the jurisdiction of Committee F17 on Plastic Piping
14、Systems and is the direct responsibility of Subcommittee F17.63 on DWV.Current edition approved June 15, 2007. Published July 2007. Originallyapproved in 1998. Last previous edition approved in 2005 as F 186605.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Cust
15、omer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.4.3 LubricantThe lubricant used for
16、 field assembly shallbe the type recommended by the manufacturer of the fitting.Prolonged exposure to the lubricant shall not damage thegasket, pipe, or fitting.5. General Requirements5.1 Fabrication Joint MaterialThe fabrication joint ma-terial or reinforcing overlays shall be of the type, strength
17、, andproperties suitable for intended fabrication. It is the decision ofthe manufacturer as to what material will be used. The PVCprimer shall meet the requirements of Specification F 656. ThePVC solvent cement shall meet the requirements of Specifica-tion D 2564.5.2 Heat Fusion WeldsFittings assemb
18、led using the heatfusion welding process shall meet all of the requirements ofthis specification.5.3 Pipe PerformancePipe that is used to fabricate fittingsshall meet all of the schedule 40 requirements of SpecificationD 1785 or D 2665.5.4 WaterwayFabricated fittings shall be constructed sothat pipe
19、 ends of branches do not project into the waterway ofthe fitting body.5.5 Gasketed Joint System The joint shall display noleakage when tested in accordance with the requirements ofSpecification D 3212 when assembled in accordance with thefitting manufacturers recommendations. All surfaces of thejoin
20、t that contact the gasket shall be smooth and free ofimperfections, ridges, fractures or cracks that could affect theseal.6. Dimensions and Permissible Variations6.1 Spigot DiameterThe outside diameter and out-of-roundness of the fitting spigot shall meet the requirements ofTable 1 when measured in
21、accordance with 10.1.16.2 Spigot LengthThe spigot length shall meet the re-quirements as given in Table 1 when measured in accordancewith 10.1.2.6.3 Wall ThicknessThe minimum wall thickness of thefitting shall meet the requirements of Table 1 when measured inaccordance with 10.1.3. In the case of fi
22、ttings fabricated frompipe sections, the thickness of the wall in the bell and brancharea shall be considered satisfactory if it was formed from pipemeeting those requirements.6.4 Solvent Cement Sockets:6.4.1 Socket DiameterThe inside diameter of the fittingsocket shall meet the requirements as spec
23、ified in Table 2 whenmeasured in accordance with 10.1.4.6.4.2 Socket DepthsThe socket depth shall meet therequirements as given in Table 2 when measured in accordancewith 10.1.5.6.5 Gasket Joint SocketsThe minimum depth and maxi-mum projection for gasket sockets, show in Fig. 1, shall meetthe dimens
24、ional values given in Table 3. Measurements shallbe made in accordance with Test Method D 2122. All otherdimensions shall be in accordance with the manufacturersspecifications.7. Properties7.1 Resistance to BendingFabricated fittings shall betested in accordance with 10.2. The bond shall not show an
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMF18662007STANDARDSPECIFICATIONFORPOLYVINYLCHLORIDEPVCPLASTICSCHEDULE40DRAINAGEANDDWVFABRICATEDFITTINGS
链接地址:http://www.mydoc123.com/p-535889.html